workshop manual citroen jumpy

You search Auto repair manual PDF about workshop manual citroen jumpy, search results will appear below. If search results do not exist, please search by others keyword.

2007 Fiat Scudo/Citroen Jumpy/Peugeot Expert Bosal Part 034931 Fittimg Instructions

Filed Under (Peugeot) by admin on 10-02-2014

Download
The vehicle manufacturer’s specifications regarding trailer load and nose weight are decisive for driving. For the max. trailer weight of your car please refer to the owner’s manual or your car homologation documents, the values specified for the towing hitch must not be exceeded. Formula for D-Value: Max. trailerweight (kg) x Max. permissible weight towing vehicle (kg) 9,81 Max. trailerweight (kg) + Max. permissible weight towing vehicle (kg) 1000 The fixing points specified as standard must be observed. National guidelines concerning official approval of accessories must be observed. These installation and operating instructions must be enclosed with the vehicle papers. Bosal cannot be held responsible for any defects in the product caused by fault or by any injudicious use whatever of the user or a person he is liable for. (sect. 185, art. 2 N.B.W.) All our products are controlled upon dispatch with a weight control system. In the case of missing parts we can only accept a request of replacement with the weight control sticker.… Read More

1999 Ford Contour/Mystique Timing Belt Workshop Manual

Filed Under (Ford) by admin on 01-01-2014

Download 1. CAUTION: The maximum amount by which the engine management system will adjust the camshaft timing (VCT control unit) is limited to two degrees. As a result of this an extremely high degree of accuracy is required for any work which affects the valve timing. NOTE: The locations of engine mountings and engine support insulators are described looking from the transaxle to the engine. NOTE: Operation steps which only apply to certain model variants and therefore do not apply to all vehicles are clearly marked. Disconnect the battery ground cable. 2. Raise and support the vehicle. For additional information, refer to Section 100-02 . 3. Loosen the right-hand front wheel nuts. 4. Remove the right-hand front wheel. 5. Remove the engine underschield (if equipped). 6. Remove the right-hand front splash shield. 7. NOTE: Mark the accessory drive belt direction if the belt is to be reused. Remove the accessory drive belt.… Read More

2000 Ford Super Duty 250-550/ Excursion/F-53 Motorhome Chassis Workshop Manual

Filed Under (Ford) by admin on 21-02-2014

Download 1. Remove the exterior mirror mounting hole cover. 2. If equipped, remove the window regulator handle. 1. Position the window regulator handle cover aside. 2. Remove the window regulator handle screw and regulator handle. 3. If equipped, remove the window control switch plate. ? Disconnect the window control switch electrical connectors and if equipped, the memory set switch electrical connector. 4. If equipped, remove the front door trim panel reflector or the courtesy lamp lens. 5. Remove the screws. 6. CAUTION: Do not pull directly outward on front door trim panel, as damage will occur. NOTE: Remove the front door trim panel by pulling it straight upward. Lift and remove the front door trim panel. 7. If equipped, twist the courtesy lamp connector one half turn and remove it from the front door trim panel. 8. CAUTION: Insert the lower panel tabs first or they can break when installing the front door trim panel.… Read More

2001 Lincoln LS Workshop Manual

Filed Under (Lincoln) by admin on 01-01-2014

Download Cooling System Draining, Filling and Bleeding. Draining WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap. CAUTION: The coolant must be recovered in a suitable, clean container for reuse. If the coolant is contaminated it must be recycled or disposed of correctly. CAUTION: Care must be taken to ensure the accessory drive belt does not become contaminated with engine coolant.… Read More

2002 Ford Explorer/Mountaineer Workshop Manual

Filed Under (Ford) by admin on 01-01-2014

Download CAUTION: Since the engine is not free-wheeling, timing procedures must be followed exactly or piston and valve damage may occur. 1. Remove the engine front cover (6019). For additional information, refer to Engine Front Cover in this section. 2. NOTE: Procedure is for either RH or LH ignition coil (12029); LH ignition coil is shown. Disconnect the ignition coil electrical connector and remove the retaining bolt. 3. Tilt the coil away from the fuel injection supply manifold. 4. Remove the ignition coil. 5. NOTE: Remove any foreign material from the spark plug wells with compressed air before removing the spark plugs. Remove the spark plugs. 6. Position the lobe of the camshaft up. 7. Install the special tool between the valve spring coils to prevent valve stem seal damage. 8. NOTE: The roller followers are positional. Mark the followers for installation in their original locations. NOTE: The last three roller followers must be removed with special service tool 303-581.… Read More

2000 Lincoln LS Workshop Manual Halfshaft

Filed Under (Ford) by admin on 02-01-2014

Download 1. CAUTION: Do not begin this procedure unless: ? a new rear axle wheel hub retainer is available. ? a new axle circlip (4B422) is available. ? you have read Halfshaft Handling in this section. NOTE: This procedure applies to both the LH and RH halfshafts. Raise and support the vehicle. For additional information, refer to Section 100-02. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-04. 3. Remove and discard the rear axle wheel hub retainer. 4. Remove the rear brake anti-lock sensor. For additional information, refer to Section 206- 09A. 5. Remove the brake disc. For additional information, refer to Section 206-04. 6. Remove the nut and bolt. 7. Using the special tools, press the outboard CV joint until it is loose in the hub. 8. CAUTION: Do not over-angulate the outboard CV joint or damage the boot. While raising the knuckle, remove the CV joint from the hub.… Read More

2002 Ford Escort Cooling System Draining, Filling and Bleeding Workshop Manual

Filed Under (Ford) by admin on 25-01-2014

Download Draining 1. Bring the engine to normal operating temperature and turn the engine off. With the cooling system under pressure, inspect cooling system hoses and clamped hose connections for leaks, excessive deterioration or contact wear. Inspect radiator installation retention. Note any discrepancies and proceed. 2. WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap.… Read More

2004 Ford F-Super Duty 250-550/Excursion Workshop Manual

Filed Under (Ford) by admin on 07-03-2014

Download 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04. 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate. 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00. Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. CAUTION: Due to the fit of the splines, the hub lock will be difficult to remove.… Read More

2002 Crown Victoria/Grand Marquis Workshop Manual

Filed Under (Ford) by admin on 31-12-2013

Download Adjust the blower motor setting to LO and then to HI. * Does the blower motor operate correctly? Yes REPAIR circuit 515 (OG/RD) for a short to ground. TEST the system for normal operation. No GO to R2 . R2 CHECK THE BLOWER MOTOR SPEED CONTROL Blower Motor Speed Control C1308 EATC Module C228b * Does the blower motor operate? Yes INSTALL a new blower motor speed control. TEST the system for normal operation. No GO to R3 . R3 CHECK THE BLOWER MOTOR SPEED CONTROL CIRCUITS FOR AN OPEN Blower Motor Speed Control C1308 Measure the resistance between the blower motor speed control C1308: * pin 1, circuit 269 (LB/OG) and the EATC module C228b pin 10. * pin 2, circuit 752 (YE/RD) and the EATC module C228b pin 23. * pin 3, circuit 754 (LG/WH) and the EATC module C228b pin 24. * Are the resistances less than 5 ohms?… Read More

1998 Ford Ranger Workshop Manual

Filed Under (Ford) by admin on 03-12-2013

Download Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Engine Stand 014-00232 or equivalent 1. Relieve the fuel pressure. For additional information, refer to Section 310-00 . 2. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 . 3. Drain the engine cooling system. For additional information, refer to Section 303-03 . 4. Remove the hood (16612). 5. Remove the air cleaner outlet tube (9B659). For additional information, refer to Section 303-12 . 6. Remove the accelerator control splash shield (9E766). 7. Remove the upper radiator hose (8260). 8. Remove the lower radiator hose (8286). 9. Remove the two bolts and position the fan shroud (8146) on the fan blade (8600). 10. Remove the water pump pulley, fan and shroud; refer to Section 303-03 . 11. Disconnect the radiator overflow tube. 2. On vehicles equipped with automatic transmissions, disconnect the transmission cooler lines. 13. Disconnect the mass air flow sensor.… Read More

You might also likeclose