2004 Chevrolet Monte Carlo SS ACCESSORIES & EQUIPMENT Theft Deterrent

Download SCHEMATIC AND ROUTING DIAGRAMS THEFT DETERRENT SYSTEM SCHEMATICS Refer to System Wiring Diagrams . COMPONENT LOCATOR THEFT DETERRENT SYSTEM COMPONENT VIEWS Fig. 1: Passlock(tm) Sensor Connector, Left Center of Instrument Panel Courtesy of GENERAL MOTORS CORP. Callouts For Fig. 1 THEFT DETERRENT SYSTEM CONNECTOR END VIEWS Passlock Sensor Terminal Identification DIAGNOSTIC STARTING POINT – THEFT DETERRENT Begin the system diagnosis with Diagnostic System Check – Theft Deterrent . The Diagnostic System Check will provide the following information: * The identification of the control module(s) which command the system. * The ability of the control module(s) to communicate through the serial data circuit. * The identification of any stored diagnostic trouble codes (DTCs) and their status. The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and where the procedure is located. DIAGNOSTIC SYSTEM CHECK – THEFT DETERRENT Test Description The number(s) below refer to the step number(s) on the diagnostic table.… Read More

Information on Error Codes on Radio Display – Their Cause and Corrective Action

Download odels: 1995-1996 Buick Roadmaster 1995-1999 Buick LeSabre 1995-2004 Buick Century, Regal 1995-2005 Buick Park Avenue 1996-1999 Buick Riviera, Skylark 2004-2005 Buick Rainier 1995-1999 Chevrolet Lumina, Monte Carlo, Fullsize Pickup Models (Old Style) 1995-2005 Chevrolet Blazer 1996 Chevrolet Lumina APV 1996-1999 Chevrolet Cavalier 1996-2000 Chevrolet Express Van 1996-2002 Chevrolet Astro Van 1997-2002 Chevrolet Camaro 1997-2003 Chevrolet Malibu 1997-2005 Chevrolet Corvette, Venture 2000-2005 Chevrolet Silverado 2002-2005 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2005 Chevrolet SSR 2004-2005 Chevrolet Classic, Colorado 1995-1999 GMC Fullsize Pickup Models (Old Style) 1995-2002 GMC Jimmy 1996-2000 GMC Savana Van 1996-2002 GMC Safari Van 2000-2005 GMC Sierra 2002-2005 GMC Envoy, Envoy XL 2004-2005 GMC Canyon, Envoy XUV 1995-1999 Oldsmobile Aurora, Eighty Eight 1995-1997 Oldsmobile Cutlass Supreme 1999-2004 Oldsmobile Alero 1998-2002 Oldsmobile Intrigue 1995-1996 Oldsmobile Ninety Eight 1996-1999 Oldsmobile Achieva 1996-2004 Oldsmobile Bravada, Silhouette 1995-1999 Pontiac Bonneville, Sunfire 1995-2002 Pontiac Firebird 1995-2005 Pontiac Grand Prix 1996-1997 Pontiac Trans Sport 1996-2000 Pontiac Grand Am 1997-2005 Pontiac Montana 2003-2005 HUMMER H2.… Read More

Service 4WD Light Illuminated, DTC C0374 Set (Inspect Wiring Harness to Transfer Case Speed Sensors, Replace Wiring Harness)

Download Models: 2004-2007 Buick Rainier 2003-2006 Chevrolet Avalanche, Suburban, Tahoe 2003-2007 Chevrolet Silverado Classic, TrailBlazer, TrailBlazer EXT 2003-2006 GMC Yukon, Yukon XL 2003-2007 GMC Envoy, Envoy XL, Sierra Classic 2003-2004 Oldsmobile Bravada 2005-2007 Saab 9-7X with Four Wheel Drive or All-Wheel Drive and Active All-Wheel Drive (RPO NP4) or Active Two-Speed (RPO NP8) Transfer Case. Condition Some customers may comment on intermittent illumination of the Service 4WD light. Upon investigation, the technician may find DTC C0374 set. The customer may also comment on intermittent erratic operation of the 4WD or AWD system after driving through rain/snow or simply going through a car wash. Cause The speed sensor signal may have become corrupted. Possible openings in the speed sensor wire insulation (twisted pairs) can allow water intrusion. Also, wire connections contaminated by water may result in short circuits and erroneous speed sensor readings. This most often occurs on the rear speed sensor circuit.… Read More

1996-2000 Honda Civic D16Y8 Performer X Turbocharging System Manual Installation Instructions

Download
Description: The Edelbrock Performer X Turbocharging System is a complete Turbo Kit that gives 1996-2000 Honda Civic SOHC VTEC D16Y8 owners a 60-70 horsepower increase from turbocharging. The Garrett T-28 ball bearing turbo comes pre-assembled as one unit with a Ni-resist cast exhaust manifold and exhaust elbow, and inlet oil and water lines for the simplest possible installation. The system includes a high-performance Performer X intake manifold with four additional injectors and a separate electronic controller to add fuel and retard spark under boosted conditions. The Edelbrock Exhaust manifold and elbow are designed for maximum flow and high velocity for quicker turbo spool-up. We have included an intercooler, blow-off valve, windshield pillar mount boost gauge, o-ring sealed compressor flanges, a turbo oil supply adapter, and pre-assembled Russell oil, water, and fuel lines to make this one of the most complete kits on the market.
INSTALLATION INSTRUCTIONS Initial Parts Removal and Intercooler Installation (See factory service manual for procedures where noted) 1.… Read More

1996 Ford Taurus With AXOD-E (AX4S)

Download 1996 Ford Taurus V6-182 3.0L Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Valve Body Service and Repair Removal and Installation With AXOD-E (AX4S) REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor.… Read More

1996 Honda XR250 Dual Sport Kit Manual Installation Instructions

Download
Remove the seat, side panels, radiator shrouds, and gas tank. If you are color blind or even think you might be a little color blind, now is the time to get someone to assist you. Successful installation of the kit requires good color recognition. You want to go riding this weekend, don’t you? 3. Unplug the green and blue taillight wires from the stock wiring harness, remove the taillight lens, and remove the taillight socket and wiring. 4. Unplug the headlight from the stock wiring harness and remove. 5. Remove the kill switch. Unplug the black/white wire and the black wire from the connector near the base of the odometer. 6. Locate the AC voltage regulator found mounted on the front top edge of the airbox as shown in Photo 1. Unplug the regulator from the wiring harness and remove regulator (Leave the U-bolt attached to the airbox and save the bolt for a later step) .… Read More

1996-2001 Audi A4 Quattro Part 57- 0515 INSTALLATION INSTRUCTIONS

Download Audi A4 2.4/2.8L V6 1995-2001 Audi A4 Quattro 2.8L V6 1996-2001 Audi A6 2.4/2.8L V6 1997-2002 Audi A6 Quattro 2.8L V6 1997-2001 1. Remove the cover from the air box assembly. (Fig. 1) 2. Unclip the electrical connector from the Mass Air Sensor (MAS). (Fig. 2) 3. Unclip and remove the intake hose from the MAS. (Fig. 3) 4. Unclip the evap control valve from the air box. (Fig. 4) 5. Unclip the wiring from the air box (Fig. 5) 6. Unbolt the air box mounting bolt. (Fig. 6) 7. Disconnect the auxiliary air pump hose from the front of the air box. (Under the intake scoop) 8. Carefully lift and remove the complete air box assembly from the vehicle. (Fig. 7) 9. Unbolt and remove the MAS from the air box. (Fig. 8) 10. Fit the MAS adaptor to the MAS using the hardware provided. (Fig. 9) 11. Refit the MAS to the intake hose using the original hose clip.… Read More

2005 Ford Mustang GT Roush Fog Lamp Wiring Harness Installation Instructions

Download 1. SAFETY REQUIREMENTS STOP! READ IMPORTANT SAFETY CAUTIONS AND WARNINGS BEFORE PROCEEDING. IMPORTANT SAFETY NOTICE Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the actual installation. 1. Always wear safety glasses for eye protection. 2. Place ignition switch in the OFF position. 3. Always apply the parking brake when working on a vehicle. 4. Block the front and rear tire surface to prevent unexpected vehicle movement. 5. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide. 6. Do not smoke or use flammable items near or around the fuel system. 7. Use chemicals and cleaners in well-ventilated areas. 8. Batteries produce explosive gases, which can cause personal injury.… Read More

How to bypass the VATS (PASSKey II) system in a late model GM vehicle

DownloadPontiac 1994-1996 Grand Prix 1992-1999 Bonneville 1993-2002 Firebird/Trans Am/Firehawk Buick 1994-1996 Regal 1992-1999 LeSabre 1991-1996 Park Avenue 1991-1996 Roadmaster Oldsmobile 1994-1997 Cutlass Supreme 1992-1999 Eighty Eight/LSS/Ninety Eight/Regency 1991-1996 Custom Cruiser Wagon Chevrolet 1995-1999 Monte Carlo 1995-2001 Lumina 1993-2002 Camaro 1986(?)-1996 Corvette (C4) Cadillac 1991-1996 Fleetwood 1992-1997(?) Seville/STS/DeVille Any other GM Vehicles with the VATS or PASSKey II system (If your ignition key looks like the one pictured below.) Alright, let’s begin the madness: 1. Take your DMM, set it to measure Ohms (use the 20k setting.) Measure the resistance across the pellet of the ignition key. Place one probe on the silver part of one side of the pellet, and the other probe on the other side. Write this value down. 2. Purchase a resistor or resistors that add up to the value measured in step 1. Radio Shack is a great place to go for the resistors, heat shrink tubing, and the “bullet-style” solderless connectors.… Read More

1996-1998 Honda Civic EX Bomz Racing Air Intake Manual Installation

Download
Removal of Factory Intake 1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. 2. Loosen the clamp on the intake tube at the throttle body. 3. Loosen and remove the two bolts that secure the airbox. 4. Disconnect the air temperature sensor electrical connection. 5. Remove the crankcase vent tube from the stock intake tube. 6. Remove the complete air intake assembly. 7. Loosen and remove the bolt that secures the wiring harness bracket to it’s support bracket. Install of Intake 8. Install the reducer onto the intake tube. 9. Install the intake tube onto the throttle body and secure it with the clamp. 10. Remove the air temperature sensor from the stock intake tube. 11. Install the air temperature into the grommet on the intake tube. 12. Insert the crankcase vent tube into the second grommet on the intake tube. 13. Reconnect the air temperature sensor electrical connection.… Read More