". Please use another keyword if these document aren't what you look for.
Filed Under (Acura) by Doe Namblas on 24-11-2013
Download (Honda Accord/Acura TSX). INSTALLATION: 1. Access the wiring on the back of the sunroof control switch. For most Hondas/Acuras this involves removing the panel directly under the steering wheel and the plastic piece under the dash. It should then be possible to push the sunroof switch pod out of the dash from behind. 2. Secure the module behind the dash panel using the included wire ties. 3. Locate a switched ignition source – this typically can be found at the ignition switch. ELECTRICAL CONNECTIONS: Due to the harsh environment found in vehicles, KP Technologies recommends always soldering and securely taping EVERY connection. In order for the “One Touch” feature to work with the “VENT” position of the sunroof it is necessary to install two diodes. To install the diodes the “OPEN” and “CLOSE” sunroof wires must be cut. If the “One Touch” feature is only required for the “OPEN” and “CLOSE” it may not necessary to cut any wires (depending on the installers method of splicing).… Read More
Download Acura TSX ONE TOUCH SUNROOF MODULE INSTALLATION MANUAL
Filed Under (Volkswagen (VW)) by Doe Namblas on 02-01-2014
Download Steering column, assembly WARNING:Special safety precautions and some different procedures apply to vehicles equipped with airbags CAUTION:Before working on the electrical system: Obtain radio anti-theft code. Ignition OFF ! Disconnect battery Ground (GND) strap. Note: After reconnecting battery: Activate vehicle equipment such as radio, clock and power windows as per service procedures and/or Owner’s Manual. On vehicles equipped with OBD II, activate readiness code. Refer to Powertrain Management, Computers and Control Systems, Testing and Inspection, Procedures See: Powertrain Management/Computers and Control Systems/Testing and Inspection For further information on the steering column assembly, refer to Steering and Suspension, Steering, Steering Column, Service and Repair. 1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig.… Read More
Download 2000 Volkswagen Cabrio Ignition Switch: Service and Repair
Filed Under (Cadillac) by Doe Namblas on 06-04-2014
Download . Circuit Description The torque converter clutch (TCC) brake switch is used to indicate the status of the brake pedal (applied or released). If the PCM detects an open TCC brake switch (stuck ON) during accelerations, then DTC P0719 sets. DTC P0719 is a type C DTC. Conditions for Running the DTC * No VSS DTCs P0502 or P0503. * DTC P0719 has not passed this ignition cycle. Conditions for Setting the DTC The TCC brake switch input is at 0 volts for 15 minutes and the following conditions occur 8 times without a status change on the TCC brake input: * The vehicle speed is less than 8 km/h (5 mph). * The vehicle accelerates to 32 km/h (20 mph) within 2-6 seconds. * Then the vehicle speed remains above 32 km/h (20 mph) for 6 seconds. Action Taken When the DTC Sets * The PCM does not illuminate the malfunction indicator lamp (MIL).… Read More
Download 2000 Cadillac DeVille Brake Switch Circuit Low Input
Filed Under (Buick) by Doe Namblas on 05-01-2014
Download BUICK Century 1997-99 LeSabre 1995-99 1 Park Avenue 1995-99 Regal 1995-99 Riviera 1996-99 Roadmaster 1995-96 Skylark 1996-98 CHEVROLET Impala 2000 Venture 2000 OLDSMOBILE Achieva 1996-98 Aurora 1995-99 Bravada 1998-99 Cutlass 1998-99 Cutlass Supreme 1995-97 Eighty-Eight 1994-99 Intrigue 1998-99 LSS 1996-99 Ninety-Eight 1994-96 Regency 1997-98 Silhouette 2000 PONTIAC Montana 2000 Sunfire 2000. BUICK LeSabre / Park Avenue 1995-99 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the plastic trim piece to the left of the glove box and (1) Phillips screw exposed. Unsnap the top edge of the knee bolster panel. Remove (1) Phillips screw from the panel. Remove the ashtray cluster and (2) Phillips screws from each side. Unclip the entire dash trim bezel and remove. Remove (3) 9/32″ hex-head screws securing the factory head unit and disconnect the wiring. Skip to the Installation Instructions for ALL VEHICLES on Page #6. CHEVROLET Impala 2000 Disconnect the negative battery terminal to prevent an accidental short circuit.… Read More
Download 1997-1999 Buick Century/Regal 99-2001 AW-200GM INSTALLATION INSTRUCTIONS
Filed Under (Other Manuals) by Doe Namblas on 16-03-2014
Download Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada.… Read More
Download Vehicles Equipped with a Webasto Sunroof System
Filed Under (Buick) by Doe Namblas on 02-01-2014
Download Tools Required z J 28467-90A Engine Support Adapters z J 28467-B Universal Engine Support Fixture z J 36462-A Engine Support Adapter Leg Set 1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical. 2. Carefully disconnect the throttle body air inlet duct. 3. Remove the engine mount struts from the engine. Refer to Engine Mount Strut Replacement . 4. Remove the drive belt. Refer to Drive Belt Replacement . 5. Install the J 28467-90A , the J 28467-B and the J 36462-A . Do not raise the engine. Refer to Engine Support Fixture . 6. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 7. Disconnect the three-way catalytic converter pipe from the right exhaust manifold. Refer to Catalytic Converter Replacement in Engine Exhaust. 8. Remove the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.… Read More
Download 2000 Buick Regal Oil Pan Replacement
Filed Under (Acura) by Doe Namblas on 24-11-2013
Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More
Download 2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module
Filed Under (Audi) by Doe Namblas on 31-12-2013
Download Audi TT Coupe 2000-2004, Audi TT Roadster 2001-2004 – Brake System. ABS/ESP ITT Mark 20 system components, removing and installing Brake light switch (square housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once. Removing – Remove storage compartment on driver’s side. Repair Manual, Body Interior, Repair Group 68; Storage compartments, covers – Unplug electrical connector. – Remove brake light switch -1- by turning counter-clockwise through 90. Installing Install in reverse sequence; note the following points: – Pull brake light switch plunger fully out. – Press brake pedal down as far as possible by hand. – Guide switch through installation hole and secure by turning 90 clockwise -arrows-. – Release brake pedal. – Make sure proper function of brake lights when brake pedal is pressed and released. Brake light switch (round housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once.… Read More
Download 2000-2004 Audi TT Coupe Brake System
Filed Under (Honda) by Doe Namblas on 27-02-2014
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More
Download 1997 Honda Civic Alarms Fitting Wiring Diagram Manual Instructions
Filed Under (Buick) by Doe Namblas on 31-12-2013
Download 2004 Buick LeSabre | LeSabre (VIN H) Service Manual. Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) Condition Some customers may comment on shaking/vibration in the steering wheel, floor or seat while driving at highway speeds (typically between 60-72 mph (96-115 km/h)) on smooth roads. Cause These specific vehicles may be sensitive to various rotating mass assemblies, especially if they are considered to be out-of-balance. Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights 3.… Read More
Download 2004 Buick LeSabre Shake/Vibration in Steering Wheel