wheree is the fuse for the auto level control on a 1992 eldorado

You search Auto repair manual PDF about wheree is the fuse for the auto level control on a 1992 eldorado, search results will appear below. If search results do not exist, please search by others keyword.

PEUGEOT 407 e253 CAR ALARM CONTROL UNIT

Filed Under (Peugeot) by admin on 01-01-2014

Download
LOCATION OF THE CAR ALARM CONTROL UNIT Compact control units and sirens: place under the bonnet on the wheel box on the driver’s side. Modular control units and accessories: place under the dashboard on the driver’s side. CAR ALARM SUPPLY Positive: Connect the Can Bus connector in the kit of accessories supplied with the e253 (see instructions for its connection in following pages). Power is taken from the Red wire (Pos. 1). Negative: Connect the Can Bus connector in the kit of accessories supplied with the e253 (see instructions for its connection in following pages). Earth is taken using the Black wire (pos. 2) IMMOBILISER Starter Motor: Cut the White wire (Pos 3) in the Black 3-pin connector under the steering wheel. ODOMETER Connect to pos 26 (Wire N° 6739) in the black 40 way connector (green part) on the BSI control unit or directly to the ABS control unit under the bonnet next to the battery in pos.… Read More

1988-1991 Honda Civic Si FUSES and CIRCUIT BREAKERS

Filed Under (Honda) by admin on 17-12-2013

Download IDENTIFICATION FUSE PANEL LOCATION The fuse box is located under dashboard on driver’s side. Underhood fuse panel is located in engine compartment beside battery. Cars equipped with anti-lock brake system have a third fuse box for ABS in front of the engine compartment on passenger’s side. FUSE PANEL IDENTIFICATION (1988-91) Fuse & Circuit Breaker Identification z 1 – 10 Amp Integrated Control Unit, Combination Switch, Gauge Assembly, Back-Up Lights Switch, Shift Position Console Switch, Clock (1990) , Shift Lock Solenoid (1990) , Interlock Control Unit (1990) Automatic Seat Belts (If Equipped) z 2 – 10 Amp Starter Solenoid, PGM-FI Main Relay, PGM-FI Electronic Control Unit, Integrated Control Unit z 3 – 20 Amp Power Door Locks (If Equipped) z 4 – 10 Amp Right Headlight High Beam, High Beam Indicator Light, Daytime Running Lights Relay (Canada) z 5 – 10 Amp Left Headlight High Beam z 6 – 30 Amp Sun Roof Motor (If Equipped) z 7 – 10 Amp Rear Lights (Canada Only) z 8 – 10 Amp Integrated Control Unit, Interior & Exterior Lighting z 9 – Blank z 10 – 10 Amp Left Headlight Low Beam z 11 – 10 Amp Right Headlight Low Beam z 12 – 15 Amp Integrated Control Unit, Luggage Compartment Light, Dome Light, Ignition Switch, Clock, Radio, Cigarette Lighter z 13 – 15/20 Amp Power Windows, Windshield Wipers & Washer, Sun Roof Relay (1990), Integrated Control Unit (Canada), Combination Switch (1990 CRX) z 14 – 10 Amp Gauge Assembly, Engine Sensors & Controls, PGM-FI Main Relay (Wagon & CRX Only), PGM-FI ECU (Wagon & CRX Only), Fuel Pump (Wagon & CRX Only), ELD Unit (Wagon & CRX Only), EACV (Wagon & CRX Only) z 15 – 15 Amp Cooling Fan Motor (Except 4WD A/T Wagon), Cooling Fan Relay z 16 – 10 Amp Daytime Running Lights (Canada Only) z 17 – 10 Amp Radio, Cigarette Lighter Relay (1990 only) z 18 – 10 Amp Rear Window Defogger, Power Door Mirrors, Air Conditioning z 19 – 30 Amp Blower Motor z 20 – 20 Amp Right Front Power Window z 21 – 20 Amp Left Front Power Window z 22 – 20 Amp Right Rear Power Window z 23 – 20 Amp Left Rear Power Window UNDERHOOD FUSE PANEL IDENTIFICATION (1988-91)Fuse & Circuit Breaker Identification z 1 – 60 Amp Power Distribution z 2 – 50 Amp Dash Fuse Box z 3 – 40 Amp Dash Fuse Box, Exterior Lighting z 4 – 10 Amp PGM-FI Electronic Control Unit, Hazard Lights, A/T Control Unit (Wagon), Integrated Control Unit (1990), Automatic Shoulder Belts (1990) z 5 – 15 Amp Horns, Brakelights, A/T Control Unit (Wagon Only), Key Interlock Solenoid (A/T Only), Seat Belt Retractors (1990) z 6 – 20 Amp Rear Window Defogger z 7 – 15 Amp PGM-FI Main Relay z 8 – 15 Amp A/C Compressor Clutch, Condenser Fan Relay… Read More

2003 Cadillac Escalade Code C0660 will reset.

Filed Under (Cadillac) by admin on 20-12-2013

Download Vehicle Application: 2003 Cadillac Escalade 5.3L, Vin T, USA/Canada 2005 Chevrolet Suburban 1500 LS 5.3L, GAS, Vin T 2003 Cadillac Escalade EXT 6.0L 2005 GMC Yukon XL 1500 Slt 5.3L, FLEX, Vin Z 2005 Chevrolet Suburban 1500 LS 5.3L, FLEX, Vin Z Customer Concern: Code C0660 will reset. Tests/Procedures: 1. Check the RTD fuse located in the underhood fuse block. 2. Check for Battery Voltage (B+) on the Orange wire at the automatic level control air compressor pin F. 3. If less than B+ at pin F, check for a wiring and connection problem between the air compressor and the underhood fuse block. 4. Disconnect the compressor leveling module connector and check the resistance from the positive battery voltage circuit of the exhaust solenoid valve and the control circuit of the exhaust solenoid valve. Should be 30-90 ohms. 5. Check for B+ on the Dark Blue wire pin B at the air compressor with the exhaust solenoid commanded off.… Read More

Honda/Acura Kit 60815 Air Lift 1000 System Manual Installation Instructions

Filed Under (Acura) by admin on 26-11-2013

Download
PREPARING THE VEHICLE: 1. Jack up the rear of the vehicle or raise on a hoist. Support the frame with safety stands so that the wheels hang (fig. 1). Remove the wheels. 2. Position a floor jack at the connecting point of the lower control arm (under the attaching flange bolt) and knuckle (fig. 2). 3. Remove the flange bolt that connects the lower control arm to the knuckle. THE LOWER CONTROL ARM IS UNDER PRESSURE FROM THE COIL SPRING. USE CAUTION DURING THIS STEP FOR SAFETY PURPOSES. 4. Lower the floor jack gradually until tension is released and the coil spring can be removed. It may be necessary to remove the lower shock bolt in order for the lower control arm to move far enough to remove the coil spring. 5. Remove the coil spring. 6. Unbolt and discard the jounce bumper and mounting bolt (fig. 2).
INSTALLING THE AIR SPRING: 1.… Read More

2002 Volvo XC70 Rear Wheel Hub Replacing

Filed Under (Volvo) by admin on 31-12-2013

Download 2002 Volvo XC70 L5-2.4L Turbo VIN 58 B5244T3 Vehicle Level Transmission and Drivetrain Drive Axles, Bearings and Joints Wheel Hub Service and Repair Rear Wheel Hub, Replacing. Special tools: 951 2050 Raise the car Remove the rear wheel the screw for the drive shaft / wheel hub. Removing the rear wheel hub. Remove the brake caliper mounting screws. Hang the caliper up with a piece of wire the locating pin for the brake disc the brake disc the ABS-cable holder the ABS sensor. Hang up the sensor using a piece of wire. Remove the spring strut from the lower control arm Note: the spring strut is slightly compressed. Remove the anti-roll bar from the upper control arm Use a Torx wrench as a counterhold so that the rubber boot is not damaged. Remove the tie rod from the wheel spindle. Angle the tie rod upwards so that the inner mounting for the control arm is exposed the screw holding the lower mounting for the control arm to the sub-frame.… Read More

1994 Mercury Cougar XR7 INTERIOR FUSE PANEL IDENTIFICATION

Filed Under (Ford) by admin on 26-04-2013

Download 1994 Mercury Cougar XR7 FUSES & CIRCUIT BREAKERS 1989-95 FUSES & CIRCUIT BREAKERS Ford Motor Co. INTERIOR FUSE PANEL IDENTIFICATION (1994-95 MODELS) On all models, the fuse panel is located under the instrument panel, left of the steering column. Fuse & Circuit Breaker Identification 1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid 9 – 10 Amp Main ABS Relay, ABS Module 10 – 10 Amp OBD-II Test Connector 11 – Not Used 12 – 5 Amp Illumination Of: Cluster, Phone Switch, Rear Defrost Switch, A/C Switch (Manual), PRNDL Indicator, Ashtray, EATC, Clock, Radio 13 – 20 Amp Cigarette Lighter, Flash-To-Pass 14 – 15 Amp Speed Control Module, ABS Module, BrakeShift Interlock, High Mount Brakelight, Brakelights, Flashers 15 – 5 Amp Cluster (Gauges), Cluster (ABS & Airbag Warning), Warning Chime, Autolight Sensor 16 – 10 Amp Integrated Module, Sport Voltmeter, Speed Control, Remote Keyless Entry, Anti-Theft, Power Window/Door Lock Switch Illumination, Radio, CD Changer, Power Antenna, Clock 17 – 30 Amp Wiper/Washer System 18 – 20 Amp Power Door Locks, Decklid Release, Fuel Door Release, Power Seats, Power Lumbar, Booster 19 – 20 Amp Power Window Motors, Moon Roof Motor UNDERHOOD FUSE PANEL IDENTIFICATION (1994 MODELS) The “high-current” fuse panel is located in the engine compartment on the L/H fender apron.… Read More

DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected

Filed Under (Other Manuals) by admin on 17-01-2014

Download DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected Refer to Engine Controls Routing Diagram, EVAP Control System Overview . System Description This DTC tests the evaporative emission (EVAP) system for a small leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the vacuum decay rate. At an appropriate time, the control module turns the EVAP canister purge valve ON and the EVAP vent valve ON. This allows the engine to draw a vacuum on the EVAP system. At a calibrated time, or vacuum level, the control module turns the EVAP canister purge valve OFF, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum decay. If the control module detects a leak larger than a calibrated amount, this DTC sets. The following table illustrates the relationship between the ON and OFF states, and the Open or Closed states of the EVAP canister purge and vent valves.… Read More

1990-1998 GM Cadillac Deville Ignition Lock Cylinder REMOVAL & INSTALLATION

Filed Under (Cadillac) by admin on 28-03-2014

Download When performing service around Supplemental Inflatable Restraint (SIR) system components or wiring, the SIR system must be disabled. Failure to do so could result in possible air bag deployment, personal injury, or unneeded SIR system repairs. Catera Disconnect the negative battery cable. 1. Remove the steering wheel. 2. Remove the inflatable restraint steering wheel module coil. 3. Insert a small pointed awl or wire into the ignition lock cylinder release pinhole. 4. Pull out the ignition lock cylinder. 5.Fig. Insert a pointed tool into the release pin hole To install: Install the lock cylinder. Look into the hole that receives the lock cylinder on the lower RH side in order to locate the locking lever. 1. Carefully push down on the locking lever using a small flat-bladed tool until an audible click is heard. 2. Place the lock cylinder into the empty hole. 3. 6. Install the inflatable restraint steering wheel module coil.… Read More

2001 Oldsmobile Alero V6-3.4L VIN E Service and Repair

Filed Under (Oldsmobile) by admin on 01-01-2014

Download 2001 Oldsmobile Alero V6-3.4L VIN E Service and RepairThe fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid. Inspect The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F) . CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe. The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid. WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole.… Read More

Compact Exhaust Brake and/or Optional Torque Converter Controller for 7.3L PowerStroke Turbo-Diesel

Filed Under (Ford) by admin on 28-12-2013

Download Exhaust Brake and/or Torque Converter Controller Kit Contents • Integrated Control Module. • Harness with labeled connections for a hassle-free install. Every possible convenience was included in the harnessing to ensure an easy installation experience. • Small Parts Bag. A baggie containing fuse taps, taps, connectors, and zip-ties and such has been included to aid your installation. • Optional Plug in Kits for your model year and make vehicle (if purchased with unit) (may also be purchased after initial sale) Tools Required: • A good DMM or DVOM (Multimeter) for probing circuits. A test light will do in a pinch, but remember that test lights can be misleading if not understood or used properly. • A good quality wire stripping/cutting/crimping tool. Your installation will only be as good as the tools used! • A wire fish (coat hanger) for running wires in tough to reach locations or through the firewall if necessary.… Read More

You might also likeclose