1993 Ford Escort FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH)

Download 1993 Ford Escort G – TESTS W/CODES – EEC-IV (1.9L)’ ’1993 ENGINE PERFORMANCE Ford Motor Co. – Self-Diagnostics – EEC-IV. CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH) Diagnostic Aids When ignition switch is in the ON or START position, the PCM connects FUEL PUMP circuit (PCM terminal No. 22) to ground. The fuel pump relay is energized and electrical current flows to the fuel pump. If PCM does not receive ignition PIP signal within 2 seconds, FUEL PUMP circuit is opened and fuel pump operation is terminated. Perform this test when instructed by QUICK TEST or CIRCUIT TEST AA. This test is only intended to diagnose: * Fuel pump relay. * Inertia Fuel Shutoff (IFS) switch. * Wiring harness circuits (B+, VPWR, FUEL PUMP, GND and POWER-TO-PUMP). * Faulty Powertrain Control Module (PCM). Fig. 31: Fuel Pump Monitor Circuit Diagram (Escort & Tracer) 1)Code 87/556: Check VPWR To Fuel Pump Relay Code 87/556 indicates a fuel pump primary circuit failure.… Read More

2000-2002 Audi TT Part RD3025p Cold Air Intake System

Download Note: Disconnect the negative battery terminal before starting this installation. 1. Remove the air intake box and air intake duct that leads to the mass air flow sensor. 2. Slip the 2 3/4″ straight hose over the mass air flow sensor use two clamps and tighten the clamp on the mass air flow sensor. (See fig. 2) 3. Take the vibra-mount and screw it into the bracket located on the side of the strut tower mount. (See fig. 3) Removing the head lamp and the front bumper. 4. Remove the 3 m6 bolts located on the extended plastic arms on the head lamp. (See fig. 4) You will also disconnect the three harness clips located on the back side of the head lamp. (See fig. 5) 5. In order to remove the bumper you need to peel back the splash guards in the wheel well. Unscrew two m6 nuts on each side of the frame located behind the splash guards.… Read More

1994 Mercury Cougar XR7 INTERIOR FUSE PANEL IDENTIFICATION

Download 1994 Mercury Cougar XR7 FUSES & CIRCUIT BREAKERS 1989-95 FUSES & CIRCUIT BREAKERS Ford Motor Co. INTERIOR FUSE PANEL IDENTIFICATION (1994-95 MODELS) On all models, the fuse panel is located under the instrument panel, left of the steering column. Fuse & Circuit Breaker Identification 1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid 9 – 10 Amp Main ABS Relay, ABS Module 10 – 10 Amp OBD-II Test Connector 11 – Not Used 12 – 5 Amp Illumination Of: Cluster, Phone Switch, Rear Defrost Switch, A/C Switch (Manual), PRNDL Indicator, Ashtray, EATC, Clock, Radio 13 – 20 Amp Cigarette Lighter, Flash-To-Pass 14 – 15 Amp Speed Control Module, ABS Module, BrakeShift Interlock, High Mount Brakelight, Brakelights, Flashers 15 – 5 Amp Cluster (Gauges), Cluster (ABS & Airbag Warning), Warning Chime, Autolight Sensor 16 – 10 Amp Integrated Module, Sport Voltmeter, Speed Control, Remote Keyless Entry, Anti-Theft, Power Window/Door Lock Switch Illumination, Radio, CD Changer, Power Antenna, Clock 17 – 30 Amp Wiper/Washer System 18 – 20 Amp Power Door Locks, Decklid Release, Fuel Door Release, Power Seats, Power Lumbar, Booster 19 – 20 Amp Power Window Motors, Moon Roof Motor UNDERHOOD FUSE PANEL IDENTIFICATION (1994 MODELS) The “high-current” fuse panel is located in the engine compartment on the L/H fender apron.… Read More

2003 Chevy Truck TrailBlazer Water Pump Replacement

Download 1. Drain the coolant. 2. Remove the fan and shroud. 3. Remove the drive belt . 4. Using the J 41240, secure the water pump pulley and remove the water pump pulley bolts. 5. Remove the J 41240. 6. Remove the water pump pulley. 7. Loosen and remove the water pump bolts. 8. Remove the water pump. 9. Clean and inspect the water pump. 10. Discard and replace the gasket. Installation Procedure 1. Install a new water pump gasket. 2. Install the water pump and secure the water pump with the bolts. Tighten * On the initial pass, tighten the bolts to 4 Nm (35 lb in). * On the final pass, tighten the bolts to 10 Nm (89 lb in). 3. Install the water pump pulley. 4. Install the water pump pulley bolts. 5. Using the J 41240, secure the water pump pulley while tightening the water pump pulley bolts.… Read More

1988-1991 Honda Civic Si FUSES and CIRCUIT BREAKERS

Download IDENTIFICATION FUSE PANEL LOCATION The fuse box is located under dashboard on driver’s side. Underhood fuse panel is located in engine compartment beside battery. Cars equipped with anti-lock brake system have a third fuse box for ABS in front of the engine compartment on passenger’s side. FUSE PANEL IDENTIFICATION (1988-91) Fuse & Circuit Breaker Identification z 1 – 10 Amp Integrated Control Unit, Combination Switch, Gauge Assembly, Back-Up Lights Switch, Shift Position Console Switch, Clock (1990) , Shift Lock Solenoid (1990) , Interlock Control Unit (1990) Automatic Seat Belts (If Equipped) z 2 – 10 Amp Starter Solenoid, PGM-FI Main Relay, PGM-FI Electronic Control Unit, Integrated Control Unit z 3 – 20 Amp Power Door Locks (If Equipped) z 4 – 10 Amp Right Headlight High Beam, High Beam Indicator Light, Daytime Running Lights Relay (Canada) z 5 – 10 Amp Left Headlight High Beam z 6 – 30 Amp Sun Roof Motor (If Equipped) z 7 – 10 Amp Rear Lights (Canada Only) z 8 – 10 Amp Integrated Control Unit, Interior & Exterior Lighting z 9 – Blank z 10 – 10 Amp Left Headlight Low Beam z 11 – 10 Amp Right Headlight Low Beam z 12 – 15 Amp Integrated Control Unit, Luggage Compartment Light, Dome Light, Ignition Switch, Clock, Radio, Cigarette Lighter z 13 – 15/20 Amp Power Windows, Windshield Wipers & Washer, Sun Roof Relay (1990), Integrated Control Unit (Canada), Combination Switch (1990 CRX) z 14 – 10 Amp Gauge Assembly, Engine Sensors & Controls, PGM-FI Main Relay (Wagon & CRX Only), PGM-FI ECU (Wagon & CRX Only), Fuel Pump (Wagon & CRX Only), ELD Unit (Wagon & CRX Only), EACV (Wagon & CRX Only) z 15 – 15 Amp Cooling Fan Motor (Except 4WD A/T Wagon), Cooling Fan Relay z 16 – 10 Amp Daytime Running Lights (Canada Only) z 17 – 10 Amp Radio, Cigarette Lighter Relay (1990 only) z 18 – 10 Amp Rear Window Defogger, Power Door Mirrors, Air Conditioning z 19 – 30 Amp Blower Motor z 20 – 20 Amp Right Front Power Window z 21 – 20 Amp Left Front Power Window z 22 – 20 Amp Right Rear Power Window z 23 – 20 Amp Left Rear Power Window UNDERHOOD FUSE PANEL IDENTIFICATION (1988-91)Fuse & Circuit Breaker Identification z 1 – 60 Amp Power Distribution z 2 – 50 Amp Dash Fuse Box z 3 – 40 Amp Dash Fuse Box, Exterior Lighting z 4 – 10 Amp PGM-FI Electronic Control Unit, Hazard Lights, A/T Control Unit (Wagon), Integrated Control Unit (1990), Automatic Shoulder Belts (1990) z 5 – 15 Amp Horns, Brakelights, A/T Control Unit (Wagon Only), Key Interlock Solenoid (A/T Only), Seat Belt Retractors (1990) z 6 – 20 Amp Rear Window Defogger z 7 – 15 Amp PGM-FI Main Relay z 8 – 15 Amp A/C Compressor Clutch, Condenser Fan Relay… Read More

2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More

AUDI/VW FSI WATER/METHANOL INJECTION SYSTEM INSTALLATION INSTRUCTIONS

Download PART #20012 2.0T FSI WATER/METHANOL INJECTION SYSTEM FOR ALL VW AND AUDI 2.0T FSI. Installation – Mechanical Step 1 Reservoir Install ? Remove front bumper to gain access to washer reservoir. ? Drill 9/16″ hole in desired bulkhead location. Note that the bulkhead can be positioned horizontally to direct the tube toward the pump. ? Remove one nut from and turn the remaining nut until it is at the very end of the bulkhead. ? Feed red tubing through the 9/16″ hole and out the top of the reservoir. ? Attach red tubing to the bulkhead on the side opposite the nut. ? Pull the tube through the bulkhead hole until the bulkhead seats against the inside of the reservoir. ? Apply liberal amount of E6000® sealant around bulkhead. ? Slide the nut you had previously removed up onto the tube and thread it onto the bulkhead. ? While pulling firmly on the red tubing, tighten the outer nut using a 17mm socket (only needs to be hand tight).… Read More

2005 PEUGEOT 407 SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS

Download
GENERAL CONNECTIONS FOR INSTALLATION ALARM/SIREN POSITION Position the compact alarms and the sirens under the dashboard driver’s side. Pass the cables using the original fairlead located behind the servobrake group. POWER SUPPLY +30: connect to the 3 mm2 YELLOW wire, at the position nr. 2, of the 2 way grey/black connector, on the coming out of the anterior part of the “BSI” central. As alternative it is possible to connect to a 8 mm2 threaded pin located in the anterior part of the fuse box. -31: connect directly to one of the ground terminals located under the dashboard, driver’s side. IGNITION WIRE +15/54: connect to 1 mm2 LEIGHT BLUE wire marked “77C”, in the grey connector located inside the tinned box in the engine compartment, driver’s side. DIRECTION INDICATORSConnection right direction indicator Connect to the 0,75 mm2 GREY wire marked 2345, in the black connector marked “GRIS” located inside the tinned box in the engine compartment, driver’s side.… Read More

2000-2007 Ford Taurus ERRATIC FLUID LEVEL READING ON TRANSAXLE DIPSTICK

Download Ford : 2000-2007 Taurus 2000-2003 Windstar 2004-2007 Freestar MERCURY: 2000-2005 Sable 2004-2007 Monterey. ISSUE: Some 2000-2007 Taurus, 2000-2005 Sable, 2000-2003 Windstar, and 2004-2007 Freestar/Monterey vehicles, equipped with a 4F50N, AX4N, or AX4S transaxle, may exhibit an erratic fluid level reading on the transaxle dipstick and possible leaks around the filler tube and grommet. The condition may be due to a restricted transaxle vent. ACTION: Repair the transaxle vent restriction by replacing the transaxle vent with a 90° vent stem, small hose clamp, two (2) tie raps, and 24″ (61 cm) of 5/16″ (8 mm) vacuum hose. The 5/16″ (8 mm) vacuum hose will be routed from the 90° vent on the transaxle back to the cowl area, next to the brake master cylinder and tie rapped in place with the end of the hose facing down. Refer to the following Service Procedures. SERVICE PROCEDURE 1. Disconnect the mass air flow (MAF) sensor electrical connector.… Read More

2001 PEUGEOT 306 SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS

Download ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, driver’s side. CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard, driver’s side. POWER SUPPLY + 30: connect to the 2 mm2 RED wire located at the position nr. 1 in the 15 way black connector of the central unit of the central locking placed under the central tunnel. – 31: connect directly to the car body. As alternative, connect directly to the negative pole of the battery. IGNITION WIRE + 15/54: connect to the wire located at the position nr. 5 of the 15 way black connector of the central unit of the central locking placed under the central tunnel. DIRECTION INDICATORS Connect to the WHITE wire at the position nr. 10 and to the BEIGE wire at the position nr. 2 located in the 15 way black connector of the central unit of the central locking placed under the central tunnel.… Read More