where is the bank 2 oxygen sensor on a 2002 kia sedona

You search Auto repair manual PDF about where is the bank 2 oxygen sensor on a 2002 kia sedona, search results will appear below. If search results do not exist, please search by others keyword.

2000 Audi A4 Quattro oxygen sensor Bank 1 sensor 1 malfunction

Filed Under (Audi) by admin on 01-01-2014

Download 2000 Audi A4 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ, USA/Canada 2000 Audi A6 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ Customer Concern: MIL on, DTC P0130 – 16514 – oxygen sensor Bank 1 sensor 1 malfunction; P0150 – 16534 – oxygen sensor Bank 2 sensor 1 malfunction. Engine has extended crank time after sitting for more than a few hours. Tests/Procedures: 1. Trouble Code P0130 (16514) indicates an electrical malfunction with the Bank1, Sensor 1 Oxygen Sensor (O2). Connect a full function Audi compatible scan tool. Enter address menu 01 “Engine Electronics”. Enter functions menu 08 “Read Measuring Value Block”. Enter display group 041. Check specified values in fields 1. Field 1 displays Oxygen Sensor (O2) Bank 1, Sensor 1 (B1S1) heater circuit resistance. Specification is 0.0 to 0.9 Kohm. Note: If the O2′s have not yet reached their operating temperature, there will be no indication in display field 1.… Read More

2001 Infiniti QX4 Direct-Hit – Hotline Archive Detail

Filed Under (Infiniti) by admin on 16-12-2013

Download Vehicle Application: 2001 Infiniti QX4 3.5L, USA/Canada 2002 Nissan Pathfinder 3.5L, USA/Canada 2001 Nissan Pathfinder 3.5L, USA/Canada2003 Infiniti QX4 3.5L, USA/Canada Customer Concern: The check engine light is on with a trouble code P1140. Tests/Procedures: 1. Check the right side (passenger side) Intake Valve Timing Control Position (IVTCP) sensor for 12 volts on the Black/White wire. 2. Check the IVTCP sensor for a good ground on the Black wire. 3. Scope the Yellow/Green signal wire and look for a square wave signal of around 8 volts. Check the pattern of the right side sensor and if unsure of the pattern, compare it to the left bank sensor. Potential Causes: IVTCP Sensor Wiring — IVTCP sensor wiring/connection. Tech Tips: This code is for the right (passenger) bank IVTCP Sensor or sensor circuit. The right and left bank sensors can be swapped from side to side to see if the code will follow the sensor.… Read More

2000-2002 Infiniti G20 MIL “ON” REAR O2 SENSOR DTC P0138/P0139/P0140

Filed Under (Infiniti) by admin on 03-02-2014

Download If a 2000 to 2002 G20 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed).… Read More

1999-2001 Infiniti Q45 (FY33) MIL “ON” REAR O2 SENSOR DTC

Filed Under (Infiniti) by admin on 10-01-2014

Download 1999-2001 Q45 (FY33) SERVICE INFORMATION If a 1999, 2000, or 2001 Q45 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) • P0158 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Max. Voltage Monitoring) • P0159 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Response Monitoring) • P0160 Heated Oxygen Sensor 2 (Rear) (Bank 2) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies.… Read More

Sorento/Sedona Throttle Position Sensor W/3.5L Engine

Filed Under (Kia) by admin on 09-12-2013

Download provides information related to the Throttle Position Sensor (TPS) for Sorento & Sedona models. Some Sorento & Sedona vehicles may exhibit diagnostic trouble codes P0121 and/or P1121. This condition mainly occurs in high ambient or desert areas, and can be related to the occasional increase in contact resistance due to excessive wear of the inner elements of the TP sensor. This bulletin describes the proper service and adjustment procedure for replacing the TP Sensor. – Effective Vehicle Information 2003-2006 Sorento 3.5L 2002-2005 Sedona 3.5L – Parts Information Part Name Previous Part No. New Part No. Throttle Position Sensor 35102 39000 35102 39000FFF – Service Procedure Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly.… Read More

2002-2004 Acura RSX AEM EMS System Installation Instructions

Filed Under (Acura) by admin on 07-02-2014

Download EMS P/N 30-1030 and 30-1030U 2001-2005 Honda Civic 2002-2004 Acura RSX 2002-2004 Honda CR-V. Relocating the Stock ECU 1) Referring to the pictures below, locate the vehicle’s stock ECU. 2) Disconnect the negative battery cable. 3) Disconnect the electrical connectors from the stock ECU. Avoid excessive stress or pulling on the wires, as this may damage the harness. Do not cut any of the wires in the factory harness to remove them. 4) Unscrew all mounting hardware and remove the stock ECU. 5) Relocate the stock ECU in a spot that best suits your needs. Extra Velcro is supplied if needed. Installing the AEM EMS 1) Using the supplied Velcro, secure the EMS in the stock location. 2) This EMS was designed from the USDM Honda/Acura ECU harness. Some non USDM Hondas do not have an immobilizer and their Fuel Pump output is at Pin E10 rather than E1 like the USDM vehicles.… Read More

2002 Cadillac DeVille DHS V8-4.6L VIN Y

Filed Under (Cadillac) by admin on 31-12-2013

Download 2002 Cadillac DeVille DHS V8-4.6L VIN Y Recall – Fuel Tank Pressure Sensor Malfunction. Product Safety – Fuel Tank Pressure Sensor # 03038A – (03/17/2004) 03038A — Fuel Tank Pressure Sensor 2002-2003 Cadillac DeVille, Seville Equipped with V8 (4.6L) Engine (LD8/L37) 2002-2003 Oldsmobile Aurora Equipped with V8 (4.0L) Engine (L47) 2002-2003 Pontiac Bonneville SSEi This bulletin is being revised to remove the parts restriction on the fuel tank and eliminate the need for the recall identification label. Please discard bulletin 03035, issued October 2003. Condition General Motors has decided that a defect which relates to motor vehicle safety exists in certain 2002-2003 model year Cadillac DeVille and Seville vehicles equipped with a V8 (4.6L) engine (LD8/L37), Oldsmobile Aurora vehicles equipped with a V8 (4.0L) engine (L47), and Pontiac Bonneville SSEi vehicles. The fuel tank pressure sensors in these vehicles are unusually susceptible to malfunctions. If the sensor malfunctions, excessive vacuum can be applied to the fuel tank during self-diagnostic testing.… Read More

2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR

Filed Under (Ford) by admin on 14-02-2014

Download SELF-DIAGNOSTICS – EEC-V (DIESEL) -2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR. Perform this test when directed by QUICK TEST. This test is intended to diagnose: Exhaust Backpressure (EBP) Sensor • Wiring Harness Circuits (SIG RTN, VREF & EBP Signal) • Powertrain Control Module (PCM) • 1) DTC P0470 This DTC indicates PCM detected EBP sensor malfunction during KOEO ON-DEMAND SELF-TEST. Possible causes for this DTC are: Faulty EBP Sensor • Open Or Shorted Circuit • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. If EBP reading is less than 18.5 psi, clear DTCs. Repeat KOEO ON-DEMAND SELF-TEST . If DTC is still present, replace PCM. If EBP reading is 18.5 psi or more, go to next step. 2) Check Signal Ground Circuit Turn ignition off. Disconnect EBP sensor connector. Sensor is located on top front of engine.… Read More

2002 Saturn SL DTC P0122

Filed Under (Saturn) by admin on 31-03-2014

Download The throttle position (TP) sensor is a potentiometer that varies resistance according to changes in throttle plate position. The powertrain control module (PCM) measures the signal voltage from the TP sensor which is a reduced value of the PCM 5-volt reference. The voltage ranges from 0.4 (+/-0.2) volts at 0% throttle position to 4.7 volts at wide open throttle. DTC P0122 sets when the TP sensor signal voltage at the PCM is below the calibrated voltage value. DTC Parameters DTC P0122 will set if TP sensor voltage is less than 0.2 volts when: z The condition exists for longer than 10 seconds. z The ignition is ON. DTC P0122 diagnostic runs continuously with ignition ON. DTC P0122 is a type A DTC. Diagnostic Aids Important If DTC P1635 is set, diagnose that DTC first. 2002 Saturn SL
To locate an intermittent problem, use a scan tool to monitor TP SENSOR voltage with ignition ON, engine OFF.… Read More

2002 Crown Victoria/Grand Marquis Fuel Injection Supply Manifold

Filed Under (Ford) by admin on 20-02-2014

Download Fuel Charging and Controls 2002 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION. Removal All vehicles WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel-related components. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in personal injury. WARNING: Fuel in the fuel system remains under high pressure even when the engine is not running. Before working on or disconnecting any of the fuel lines or fuel system components, the fuel system pressure must be relieved. Failure to follow these instructions may result in personal injury. 1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 . 2. Relieve the fuel pressure. For additional information, refer to Section 310-00A (Gasoline) or Section 310-00B (Natural Gas). 3. Disconnect the fuel lines. For additional information, refer to Section 310-00A (Gasoline) or Section 310-00B (Natural Gas).… Read More

You might also likeclose