2005 Dodge Truck Dakota TRANSMISSION SOLENOID/TRS

Download The transmission solenoid/TRS assembly is internal to the transmission and mounted on the valve body assembly. The assembly consists of six solenoids that control hydraulic pressure to the six friction elements (transmission clutches), and the torque converter clutch. The pressure control solenoid is located on the side of the solenoid/TRS assembly. The solenoid/TRS assembly also contains five pressure switches that feed information to the TCM. OPERATION SOLENOIDS Solenoids are used to control the L/R, 2C, 4C, OD, and UD friction elements. The reverse clutch is controlled by line pressure and the position of the manual valve in the valve body. All the solenoids are contained within the Solenoid and Pressure Switch Assembly. The solenoid and pressure switch assembly contains one additional solenoid, Multi-Select (MS), which serves primarily to provide 2nd and 3rd gear limp-in operation. The solenoids receive electrical power from the Transmission Control Relay through a single wire. The TCM energizes or operates the solenoids individually by grounding the return wire of the solenoid as necessary.… Read More

1999 Ford EXPLORER TRANSMISSION SLIPPING SHIFT/DELAYED

Download FORD: 1999 EXPLORER, RANGER MERCURY: 1999 MOUNTAINEER 6. Inspect the fluid pan for major contamination. ISSUE Slipping transmission shifts and/or delayed or no •If contamination is minimal, clean the main transmission engagements may occur on some control, but do not replace. vehicles. The Electronic Pressure Control (EPC) •If major contamination is present, perform solenoid may cause stress on the attaching bracket. normal transmission overhaul as required, This stress causes the bracket to break and the including main control replacement. Pay EPC solenoid to back out of its bore causing line particular attention to the condition of the pressure to drop too low or fluctuate, allowing friction plates. Repair as required. friction clutches to slip. 7. After repairs are completed, verify concern has ACTION been fixed. Diagnose and inspect for damaged EPC attachment PART NUMBER PART NAME bracket, and replace the bracket and EPC solenoid with new bracket and revised EPC solenoid.… Read More

General Motors Accessories Headrest DVD System Display Monitor Inoperative

Download Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps.… Read More

2003 Cadillac Escalade Code C0660 will reset.

Download Vehicle Application: 2003 Cadillac Escalade 5.3L, Vin T, USA/Canada 2005 Chevrolet Suburban 1500 LS 5.3L, GAS, Vin T 2003 Cadillac Escalade EXT 6.0L 2005 GMC Yukon XL 1500 Slt 5.3L, FLEX, Vin Z 2005 Chevrolet Suburban 1500 LS 5.3L, FLEX, Vin Z Customer Concern: Code C0660 will reset. Tests/Procedures: 1. Check the RTD fuse located in the underhood fuse block. 2. Check for Battery Voltage (B+) on the Orange wire at the automatic level control air compressor pin F. 3. If less than B+ at pin F, check for a wiring and connection problem between the air compressor and the underhood fuse block. 4. Disconnect the compressor leveling module connector and check the resistance from the positive battery voltage circuit of the exhaust solenoid valve and the control circuit of the exhaust solenoid valve. Should be 30-90 ohms. 5. Check for B+ on the Dark Blue wire pin B at the air compressor with the exhaust solenoid commanded off.… Read More

2001 PEUGEOT 306 SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS

Download ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, driver’s side. CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard, driver’s side. POWER SUPPLY + 30: connect to the 2 mm2 RED wire located at the position nr. 1 in the 15 way black connector of the central unit of the central locking placed under the central tunnel. – 31: connect directly to the car body. As alternative, connect directly to the negative pole of the battery. IGNITION WIRE + 15/54: connect to the wire located at the position nr. 5 of the 15 way black connector of the central unit of the central locking placed under the central tunnel. DIRECTION INDICATORS Connect to the WHITE wire at the position nr. 10 and to the BEIGE wire at the position nr. 2 located in the 15 way black connector of the central unit of the central locking placed under the central tunnel.… Read More

Honda/Acura Kit 60815 Air Lift 1000 System Manual Installation Instructions

Download
PREPARING THE VEHICLE: 1. Jack up the rear of the vehicle or raise on a hoist. Support the frame with safety stands so that the wheels hang (fig. 1). Remove the wheels. 2. Position a floor jack at the connecting point of the lower control arm (under the attaching flange bolt) and knuckle (fig. 2). 3. Remove the flange bolt that connects the lower control arm to the knuckle. THE LOWER CONTROL ARM IS UNDER PRESSURE FROM THE COIL SPRING. USE CAUTION DURING THIS STEP FOR SAFETY PURPOSES. 4. Lower the floor jack gradually until tension is released and the coil spring can be removed. It may be necessary to remove the lower shock bolt in order for the lower control arm to move far enough to remove the coil spring. 5. Remove the coil spring. 6. Unbolt and discard the jounce bumper and mounting bolt (fig. 2).
INSTALLING THE AIR SPRING: 1.… Read More

TSB 4 WHEEL DRIVE/ALL WHEEL DRIVE WITH CONTROL TRAC

Download FORD: 1997-2008 Expedition, Explorer 2006-2008 F-150 2007-2008 Explorer Sport Trac 2008 F-150 LINCOLN: 1998-2008 Navigator 2003-2005 Aviator MERCURY: 2005 Mountaineer 2006-2008 Mountaineer. ISSUE: Various 1997-2008 vehicles equipped with either 4 wheel drive or all wheel drive and equipped with control trac may exhibit a shudder on acceleration/deceleration, binding in slow speed turns or noise from the front driveline and/or transfer case. The shudder/binding will occur with the vehicle being operated in the awd/auto 4×4 mode. The shudder/binding may be due to incorrect tire circumference or improper tire inflation pressures. ACTION: Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE 1. Review the tire label for correct tire size and tire inflation pressures located at the B-Pillar of the driver’s door. 2. If the tire size does not match the label, this procedure does not apply, follow normal Workshop Manual (WSM) diagnostics. 3. If the tire size is correct, ensure tire pressures are within specifications.… Read More

1997-2001 Acura Integra Type-R Racing Intake Manifold

Download Part # 307-05-0290 Racing Intake Manifold for • 1999-2000 Honda Civic Si • 1997-2001 Acura Integra Type-R • 1992-1993 Acura Integra GSR • 1994-1997 Honda Del Sol DOHC VTEC. Removal 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt manifold bracket from engine block and intake manifold. This bracket will not be used in assembly and installation. Remove intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors.… Read More

DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected

Download DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected Refer to Engine Controls Routing Diagram, EVAP Control System Overview . System Description This DTC tests the evaporative emission (EVAP) system for a small leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the vacuum decay rate. At an appropriate time, the control module turns the EVAP canister purge valve ON and the EVAP vent valve ON. This allows the engine to draw a vacuum on the EVAP system. At a calibrated time, or vacuum level, the control module turns the EVAP canister purge valve OFF, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum decay. If the control module detects a leak larger than a calibrated amount, this DTC sets. The following table illustrates the relationship between the ON and OFF states, and the Open or Closed states of the EVAP canister purge and vent valves.… Read More