2000-2002 Infiniti G20 MIL “ON” REAR O2 SENSOR DTC P0138/P0139/P0140

Download If a 2000 to 2002 G20 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed).… Read More

1999-2001 Infiniti Q45 (FY33) MIL “ON” REAR O2 SENSOR DTC

Download 1999-2001 Q45 (FY33) SERVICE INFORMATION If a 1999, 2000, or 2001 Q45 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) • P0158 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Max. Voltage Monitoring) • P0159 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Response Monitoring) • P0160 Heated Oxygen Sensor 2 (Rear) (Bank 2) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies.… Read More

Vehicles Equipped with a Webasto Sunroof System

Download Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada.… Read More

2001 PEUGEOT 306 SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS

Download ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, driver’s side. CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard, driver’s side. POWER SUPPLY + 30: connect to the 2 mm2 RED wire located at the position nr. 1 in the 15 way black connector of the central unit of the central locking placed under the central tunnel. – 31: connect directly to the car body. As alternative, connect directly to the negative pole of the battery. IGNITION WIRE + 15/54: connect to the wire located at the position nr. 5 of the 15 way black connector of the central unit of the central locking placed under the central tunnel. DIRECTION INDICATORS Connect to the WHITE wire at the position nr. 10 and to the BEIGE wire at the position nr. 2 located in the 15 way black connector of the central unit of the central locking placed under the central tunnel.… Read More

Information on Error Codes on Radio Display – Their Cause and Corrective Action

Download odels: 1995-1996 Buick Roadmaster 1995-1999 Buick LeSabre 1995-2004 Buick Century, Regal 1995-2005 Buick Park Avenue 1996-1999 Buick Riviera, Skylark 2004-2005 Buick Rainier 1995-1999 Chevrolet Lumina, Monte Carlo, Fullsize Pickup Models (Old Style) 1995-2005 Chevrolet Blazer 1996 Chevrolet Lumina APV 1996-1999 Chevrolet Cavalier 1996-2000 Chevrolet Express Van 1996-2002 Chevrolet Astro Van 1997-2002 Chevrolet Camaro 1997-2003 Chevrolet Malibu 1997-2005 Chevrolet Corvette, Venture 2000-2005 Chevrolet Silverado 2002-2005 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2005 Chevrolet SSR 2004-2005 Chevrolet Classic, Colorado 1995-1999 GMC Fullsize Pickup Models (Old Style) 1995-2002 GMC Jimmy 1996-2000 GMC Savana Van 1996-2002 GMC Safari Van 2000-2005 GMC Sierra 2002-2005 GMC Envoy, Envoy XL 2004-2005 GMC Canyon, Envoy XUV 1995-1999 Oldsmobile Aurora, Eighty Eight 1995-1997 Oldsmobile Cutlass Supreme 1999-2004 Oldsmobile Alero 1998-2002 Oldsmobile Intrigue 1995-1996 Oldsmobile Ninety Eight 1996-1999 Oldsmobile Achieva 1996-2004 Oldsmobile Bravada, Silhouette 1995-1999 Pontiac Bonneville, Sunfire 1995-2002 Pontiac Firebird 1995-2005 Pontiac Grand Prix 1996-1997 Pontiac Trans Sport 1996-2000 Pontiac Grand Am 1997-2005 Pontiac Montana 2003-2005 HUMMER H2.… Read More

1995 Oldsmobile Cutlass Supreme DTC 77

Download Direct-Hit 1995 Oldsmobile Cutlass Supreme 3.1L Test Details Hotline Archive # 97688 Confirmed Fix Vehicle Application: 1993 Chevrolet Camaro 3.4L 1995 Chevrolet Camaro 3.4L, Vin S 1994 Buick Skylark Custom 3.1L, Vin M, Eng Cfg V6 1995 Chevrolet Lumina 3.1L 1994 Chevrolet Corsica 3.1L, Vin M, Eng Cfg V6 1995 Pontiac Grand AM SE 3.1L, Vin M, Eng Cfg V6 1994 Oldsmobile Cutlass Supreme S 3.1L, Vin M 1995 Pontiac Grand Prix SE 3.1L Customer Concern: DTC 77. Tests/Procedures: 1. Remove the throttle body, and inspect the Exhaust Gas Recirculation Valve (EGR) port in the intake plenum. 2. The passage plugs at the bottom where it dumps into the plenum. 3. Best to use an old speedometer cable in a drill to run inside the passage to knock all the carbon out. Potential Causes: Restricted Exhaust Gas Recirculation (EGR) Passages Tech Tips: When an EGR solenoid is activated by the Powertrain Control Module (PCM), the PCM monitors the change in the Manifold Absolute Pressure (MAP) reading.… Read More

2005 PEUGEOT 407 SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS

Download
GENERAL CONNECTIONS FOR INSTALLATION ALARM/SIREN POSITION Position the compact alarms and the sirens under the dashboard driver’s side. Pass the cables using the original fairlead located behind the servobrake group. POWER SUPPLY +30: connect to the 3 mm2 YELLOW wire, at the position nr. 2, of the 2 way grey/black connector, on the coming out of the anterior part of the “BSI” central. As alternative it is possible to connect to a 8 mm2 threaded pin located in the anterior part of the fuse box. -31: connect directly to one of the ground terminals located under the dashboard, driver’s side. IGNITION WIRE +15/54: connect to 1 mm2 LEIGHT BLUE wire marked “77C”, in the grey connector located inside the tinned box in the engine compartment, driver’s side. DIRECTION INDICATORSConnection right direction indicator Connect to the 0,75 mm2 GREY wire marked 2345, in the black connector marked “GRIS” located inside the tinned box in the engine compartment, driver’s side.… Read More

2000-2002 Audi TT Part RD3025p Cold Air Intake System

Download Note: Disconnect the negative battery terminal before starting this installation. 1. Remove the air intake box and air intake duct that leads to the mass air flow sensor. 2. Slip the 2 3/4″ straight hose over the mass air flow sensor use two clamps and tighten the clamp on the mass air flow sensor. (See fig. 2) 3. Take the vibra-mount and screw it into the bracket located on the side of the strut tower mount. (See fig. 3) Removing the head lamp and the front bumper. 4. Remove the 3 m6 bolts located on the extended plastic arms on the head lamp. (See fig. 4) You will also disconnect the three harness clips located on the back side of the head lamp. (See fig. 5) 5. In order to remove the bumper you need to peel back the splash guards in the wheel well. Unscrew two m6 nuts on each side of the frame located behind the splash guards.… Read More

2003-2004 Honda Accord V6 REPAIR PROCEDURE

Download MIL Comes On With DTC P2195 or P2197 (Supersedes 04-038, dated August 10, 2004, to update the information marked with the black bars) SYMPTOM The MIL is on, and DTC P2195 (rear air fuel ratio sensor signal stuck lean) or P2197 (front air fuel ratio sensor signal stuck lean) is set. PROBABLE CAUSE The ECM/PCM software incorrectly interprets sensor inputs, causing the codes to set. REPAIR PROCEDURE NOTE: •Before you update an ECM/PCM, make sure the battery in the vehicle is fully charged. •To prevent ECM/PCM damage, do not operate anything electrical (audio system, brakes, A/C, power windows, moonroof, etc.) during the update. 1. If not already done, load the May 2004 or later i N CD onto the i N master terminal. Loading instructions are included with the CD. 2. Update the ECM/PCM software with the HIM. For updating instructions, refer to Programming the HIM and Updating an ECM/PCM With a Programmed HIM in Service Bulletin 01-023, Updating Control Units/Modules .… Read More

2003 BMW 325I Sport Wagon Check engine light on and fault codes stored

Download 2002 BMW 325I 2.5L 2003 BMW 325I Sport Wagon 2.5L, Eng Des M54, USA Customer Concern: Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible.… Read More