2002-2005 Audi A4 Intake Kit Installation Instructions

Download Kit Part # 51/54-10322. Complete kit. Make sure you have all the components before you begin your installation. Complete stock intake. a. Remove two screws holding factory fresh air duct in place. b. Pull fresh air duct out of vehicle and save for later use a. Remove two screws holding top half of airbox in place. b. Loosen clamp holding factory tube in place. c. Unplug MAF Sensor Remove top half of factory airbox. Remove clamp holding top breather filter on factory tube. Remove clamps holding second breather from top of factory tube. Save elbow for later use. Remove clamps holding third breather filter from top of factory tube. Plug can be disconnected for ease of removal. Loosen clamp holding fourth breather down from top of tube with slotted screwdriver. Loosen clamp at turbo and Last breather tube. Pull factory tube out of vehicle. Pull off front grill near Passenger side fog lamp.… Read More

Audi A4 Bluetooth Hands Free Kit Installation Instruction

Download Audi A3 (8P) Sportback, Cabrio Audi A4 (8E) B6, B7 Audi A6 (4B)* Audi TT (8J) Roadster, Coupe´ Audi A4 (8K) Audi A5 (8T) Bluetooth Hands Free Kit Installation Instruction. Installation instruction – A3 (8P), A4 (8E), A6 (4B), TT Please remove the head unit using suitable tools, after removing disconnect the necessary wiring. With a plug & play connection you will complete the fitting of the hands free kit. Please see scheme below. Unlock the connection and put the delivered wiring between the head unit and the connector coming from the vehicle. Wire the loom for the interface connection towards the glove box. Find a suitable location for the interface box within the vehicle. Make sure you will reach the interface at any time (regarding to software updates). ATTENTION: Does the vehicle have airbags fitted along the A-column it is essential to wire the loom for the microphone BEHIND the airbag.… Read More

2000 Audi A4 Quattro oxygen sensor Bank 1 sensor 1 malfunction

Download 2000 Audi A4 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ, USA/Canada 2000 Audi A6 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ Customer Concern: MIL on, DTC P0130 – 16514 – oxygen sensor Bank 1 sensor 1 malfunction; P0150 – 16534 – oxygen sensor Bank 2 sensor 1 malfunction. Engine has extended crank time after sitting for more than a few hours. Tests/Procedures: 1. Trouble Code P0130 (16514) indicates an electrical malfunction with the Bank1, Sensor 1 Oxygen Sensor (O2). Connect a full function Audi compatible scan tool. Enter address menu 01 “Engine Electronics”. Enter functions menu 08 “Read Measuring Value Block”. Enter display group 041. Check specified values in fields 1. Field 1 displays Oxygen Sensor (O2) Bank 1, Sensor 1 (B1S1) heater circuit resistance. Specification is 0.0 to 0.9 Kohm. Note: If the O2′s have not yet reached their operating temperature, there will be no indication in display field 1.… Read More

1996-2001 Audi A4 Quattro Part 57- 0515 INSTALLATION INSTRUCTIONS

Download Audi A4 2.4/2.8L V6 1995-2001 Audi A4 Quattro 2.8L V6 1996-2001 Audi A6 2.4/2.8L V6 1997-2002 Audi A6 Quattro 2.8L V6 1997-2001 1. Remove the cover from the air box assembly. (Fig. 1) 2. Unclip the electrical connector from the Mass Air Sensor (MAS). (Fig. 2) 3. Unclip and remove the intake hose from the MAS. (Fig. 3) 4. Unclip the evap control valve from the air box. (Fig. 4) 5. Unclip the wiring from the air box (Fig. 5) 6. Unbolt the air box mounting bolt. (Fig. 6) 7. Disconnect the auxiliary air pump hose from the front of the air box. (Under the intake scoop) 8. Carefully lift and remove the complete air box assembly from the vehicle. (Fig. 7) 9. Unbolt and remove the MAS from the air box. (Fig. 8) 10. Fit the MAS adaptor to the MAS using the hardware provided. (Fig. 9) 11. Refit the MAS to the intake hose using the original hose clip.… Read More

Audi RS4 Quattro Part 57-0574 INSTALLATION INSTRUCTIONS

Download Audi RS4 Quattro 2.7L V6 ‘Bi-Turbo’ Apr’00- 1. Disconnect the negative terminal from the battery. 2. Remove the plastic cover from the air box assembly. (Fig. 1) 3. Remove the air box feed pipe from between the air box lid & slam panel intake scoop. (Fig. 2) 4. Unclip & remove the electrical harness plug from the MAS (Mass Air Sensor). (Fig. 3) 5. Unclip & remove the intake hose from the MAS. (Fig. 4) 6. Unclip the 3 hoses from the top of the air box assembly. (Fig. 5) 7. Unbolt & remove the two ignition amplifiers from the top of the air box lid. (Fig. 6) 8. Unclip & remove the air box lid & filter from the vehicle. (Fig. 7) 9. Remove the small vacuum tube from the hose located at the base of the air box assembly. (Fig. 8) 10. Remove the bolt securing the air box assembly to the inner wing & carefully remove the assembly from the vehicle.… Read More

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Download Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) #05-07-30-031: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) – (Nov 11, 2005) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case.… Read More

2000-2003 AUDI A6 QUATTRO BRACKETRON PHONE MOUNT

Download AUDI A4, S4, QUATTRO (2000-2002) AUDI A6 QUATTRO (2000-2003) AUDI ALLROAD QUATTRO (2001-2003). NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT . All phone mount instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.TOOLS NEEDED: Two (2) sets of Audi DIN Radio Removal Tools, (Btron Part # SIT-102 One (1) Flat Headed Screwdriver or Dash Trim Tool (Btron Part # SIT-104), 5/16″ socket and driver . PARTS INCLUDED: One phone mount and instructions. LOCATION OF MOUNT: To the Right of the Radio. Installation Instructions 1. Locate four slots on the face of the radio. Insert four Audi DIN tools in these four slots until you hear or feel the tools click or lock. Note: There is a rubber seal that wraps around the radio between the radio and the dash pad.… Read More

Audi S4 Supercharged HyperFlow Induction System

Download Step 1- Remove OEM induction connector The factory induction system is on the passenger front corner of the car (right side). Shown in Figure 1. Figure 2- Remove the intake runner connector by pulling it away from the intake box first. Then Remove the remainder from the front of the intake area. Figure 3 shows the piece removed. This piece is not reused with the HyperFlow. Step 2- Free up main airbox connections. Figure 4, undo the reusable clamp on the intake hose near the airbox. Step 2- Continued, free up airbox connections. Figure 5- Undo the hose clip on the small box of the intake pipe near the firewall. Figure 6- Disconnect the vacuum line from the rear of the intake tube by pulling it off the barb. Step 3- Removal of factory intake tube. Figure 7- Using your 7mm nut driver or socket set loosen the band clamp on the intake tube at the throttle body.… Read More

2000 Chevy Truck S10/T10 Transfer Case Replacement

Download 2000 Chevy Truck S10/T10 Blazer 4WD V6-4.3L VIN W Vehicle Level Transmission and Drivetrain Transfer Case Service and Repair NVG 233/243-NP1 Transfer Case Replacement. Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 7. Remove any wiring harness from the transfer case. 8. Support the transfer case with a transmission jack. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case. 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case.… Read More

2008 Audi A4 Custom Body Side Molding PART FE-AUDI-A4 INSTALLATION INSTRUCTIONS

Download FOR: 2008 + Audi A4. PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION 1. LOCATION ( See Diagram below ): Using masking tape, run the tape as seen in Diagram below from POINT A to POINT B. Press tape against the vehicle, making sure that the tape is straight from POINT A to POINT B. 2. CLEAN AND PREP : For proper installation of Custom Body Side Molding, clean the surface where the molding is to be installed using the alcohol pads enclosed. Wipe off excess residue with a clean cloth. Apply PRO- BOND ADHESIVE PROMOTOR in the crush swab self-applicator. Squeeze the applicator until you feel the applicator “crush”. The applicator will become wet on the end and is ready for use. Quickly apply a thin coat of PRO-BOND below the masking tape line, no further than 1 ¼” below the tape. Be careful not to go lower than 1 ¼” because PRO-BOND could dull the paint surface.… Read More