2005 Toyota Truck Sienna Tire Monitor System – Information/Reinitialization

Download TIRE PRESSURE WARNING SYSTEM INFORMATION AND RE-INITIALIZATION Models ’04 – ’05 Highlander, RAV4, Sienna, & Solara, ’05 Scion tC October 7, 2004 TSB REVISION NOTICE : Previous versions of this TSB should be discarded. Introduction This service bulletin provides the proper procedures for normal maintenance re- initialization of the indirect Tire Pressure Warning System (TPWS). When performing service that requires tire rotation or tire replacement, suspension component replacement or alignments, the Tire Pressure Warning System must be re-initialized. During initialization, the Tire Pressure Warning System, located within the ABS or Skid Control ECU, learns the tire sizes from rotational speeds and resonance frequencies. Once the system has initialized, if tire pressures drop, the TPWS light will illuminate. If the initialization of the Tire Pressure Warning System is not conducted correctly, the low tire message indicator on the combination meter display may illuminate without a noticeable change in tire pressure. Always initialize the system using the procedures listed in this TSB.… Read More

Audi A4 Saloon Fitting instructions Electrical installation kit

Download Part 8E5 055 203 G. Vehicle model: Audi A4 Saloon and Avant, RHD, 7-pin. Install electrical kit 1. Disconnect battery. 2. Remove the following covers and panelling, as necessary: • In the boot – Boot floor cover – Loading sill cover – Left side panel • Along the right hand side of the vehicle – Scuff plates, driver’s side – Right panelling by the steering column – Fuse box cover 3. Remove the cover from the 40 mm hole in the floor panel, below the left tail light (Fig. 1/5). Note In vehicles with tyre pressure check: remove the 4-pin plug from the tyre pressure monitoring unit at the back right on the bumper. Unlock the black outer housing on this plug, open the green secondary lock and unclip the three cables. Remove the hole grommet 4B0 971 908 from this cable loom. On the towing hitch cable set, expose the second opening of the hole grommet 4B0 971 908, feed the cable set for the tyre pressure check and seal it correctly.… Read More

1999-2003 FORD SUPER DUTY F SERIES HIGH PRESSURE OIL PUMP LEAK

Download FORD: 1998-2003 E SERIES 1999-2003 SUPER DUTY F SERIES 2000-2003 EXCURSION, F-650, F-750 This article supersedes TSB 03-21-50 to update the WARNING service procedure and illustration. DO NOT REMOVE OR ATTEMPT TO REPAIR A LEAK AT THE PLUG PICTURED IN LOWER LEFT ISSUE CORNER OF FIGURE 1, OR DAMAGE TO THE Some 1998-2003 E-Series, 1999-2003 Super Duty, PUMP WILL RESULT. 2000-2003 Excursion, and 2000-2003 F650/750 1998-2003 E-SERIES HIGH PRESSURE OIL vehicles equipped with a 7.3L Diesel engine may PUMP ACCESS PROCEDURE (DISASSEMBLY) exhibit an oil leak at the high pressure oil pump outlet fittings and/or end plug (see Figure 1). The 1. Remove the Intake Air Resonator. For leak may appear to be a rear main crankshaft seal, additional information, refer to Section 303-12 in oil pan gasket, or other engine oil leak due to the the appropriate Workshop Manual. drain hole machined in the crankcase valley which allows any oil in the valley to run down the back of 2.… Read More

2001 Lincoln LS Workshop Manual

Download Cooling System Draining, Filling and Bleeding. Draining WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap. CAUTION: The coolant must be recovered in a suitable, clean container for reuse. If the coolant is contaminated it must be recycled or disposed of correctly. CAUTION: Care must be taken to ensure the accessory drive belt does not become contaminated with engine coolant.… Read More

2005 Dodge Truck Dakota TRANSMISSION SOLENOID/TRS

Download The transmission solenoid/TRS assembly is internal to the transmission and mounted on the valve body assembly. The assembly consists of six solenoids that control hydraulic pressure to the six friction elements (transmission clutches), and the torque converter clutch. The pressure control solenoid is located on the side of the solenoid/TRS assembly. The solenoid/TRS assembly also contains five pressure switches that feed information to the TCM. OPERATION SOLENOIDS Solenoids are used to control the L/R, 2C, 4C, OD, and UD friction elements. The reverse clutch is controlled by line pressure and the position of the manual valve in the valve body. All the solenoids are contained within the Solenoid and Pressure Switch Assembly. The solenoid and pressure switch assembly contains one additional solenoid, Multi-Select (MS), which serves primarily to provide 2nd and 3rd gear limp-in operation. The solenoids receive electrical power from the Transmission Control Relay through a single wire. The TCM energizes or operates the solenoids individually by grounding the return wire of the solenoid as necessary.… Read More

2000 Honda Accord EX Coupe Repair Instructions

Download Applies To: 1998-00 Accord L4 – See VEHICLES AFFECTED MIL Comes On With DTCs P0171 and/or P0172 (Supersedes 00-018, dated March 14, 2000) SYMPTOM The MIL (Malfunction Indicator Lamp) comes on with DTCs P0171 (Fuel System Too Lean) and/or P0172 (Fuel System Too Rich) stored in the ECM/PCM . PROBABLE CAUSE Moisture in the fuel pressure regulator. VEHICLES AFFECTED 1998-99 2-door: ALL 1998-99 4-door: ALL 2000 2-door:From VIN 1HGCG3. . .YA000001 thru YA000919 2000 4-door:From VIN 1HGCG6. . .YA000001 thru YA002332 From VIN 1HGCG5. . .YA000001 thru YA012613 From VIN JHMCG5. . .YC000001 thru YC000015 VIN JHMCG6. . .YC000001 CORRECTIVE ACTION Replace the fuel pressure regulator, and reroute the fuel pressure regulator vacuum line. PARTS INFORMATION Fuel Pressure Regulator (All):P/N 16740-PAA-A01, H/C 5429048 Fuel Pressure Regulator Tube Kit A (M/T with cruise control):P/N 06168-PAA-A10, H/C 6383186 Fuel Pressure Regulator Tube Kit B (A/T with cruise control):P/N 06168-PAA-A60, H/C 6383160 Fuel Pressure Regulator Tube Kit C (M/T without cruise control):P/N 06168-PAB- A00, H/C 6383194 Fuel Pressure Regulator Tube Kit D (A/T without cruise control):P/N 06168-PAB- A50, H/C 6383178 REPAIR PROCEDURE 1.… Read More

Acura Integra Fuel Pressure Gauge Set Installation Instructions

Download

Honda Civic/CRX/del Sol Acura Integra/NSX – Eagle Talon Mitsubishi Eclipse – Plymouth Laser Part Number 46054. INSTALLATION The fuel pressure tap on the late model Honda Civic/CRX/del Sol, Acura Integra/NSX, Mitsubishi Eclipse, Eagle Talon & Plymouth Laser is located on top of the fuel filter which is mounted on the passenger side firewall (driver’s side for the NSX). We suggest the vehicle be allowed to cool for a while before you begin since you will be working around the fuel system. CAUTION: THE FUEL SYSTEM CONTAINS FUEL UNDER HIGH PRESSURE EVEN WHEN THE ENGINE IS NOT RUNNING. BEFORE DISCONNECTING A FUEL LINE, WRAP THE FITTING WITH A RAG TO PREVENT FUEL SPRAY. Remove the fuel pump fuse from the fusebox. Try starting the vehicle several times until it will not remain running. This will help relieve pressure in the fuel system. (NOTE: For some vehicles it may be helpful to remove the battery).… Read More

2002 Ford Escort Cooling System Draining, Filling and Bleeding Workshop Manual

Download Draining 1. Bring the engine to normal operating temperature and turn the engine off. With the cooling system under pressure, inspect cooling system hoses and clamped hose connections for leaks, excessive deterioration or contact wear. Inspect radiator installation retention. Note any discrepancies and proceed. 2. WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap.… Read More

2001 Ford Lincoln LS Intake Manifold Upper

Download 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01. 2. Drain the engine cooling system. For additional information, refer to Section 303-03 . 3. Remove the engine appearance cover. 4. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 5. Disconnect the throttle position (TP) sensor and the idle air control (IAC) solenoid electrical connectors. 6. Disconnect the accelerator and speed control cables. 7. Remove the cable bracket. 1. Remove the bolts. 2. Remove the bracket. 8. Disconnect the throttle body hoses. 1. Disconnect the coolant hoses. 2. Disconnect the positive crankcase ventilation (PCV) hose. 3. Disconnect the vapor purge hose. 9. Disconnect the vacuum hose. 10. Disconnect the EGR to exhaust manifold tube nut. 11. Remove the cowl vent screen. For additional information, refer to Section 501-02 . 12. Remove the brace. 13. Remove the vacuum hoses from the mounting bracket.… Read More

Steering Vibration/Shudder During Parking Manuever

Download Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville. Condition Some customers may comment on a steering vibration, shudder or moan noise when steering during parking maneuvers on dry pavement. Correction Install a new power steering pressure (inlet) hose assembly on the following vehicles: Install a new power steering pressure (inlet) and return (outlet) hose assembly on the following vehicles: Diagnosis Important: In diagnosing the above listed vehicles, do not overlook other obvious repairs prior to replacing the hose(s). 1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions.… Read More