video how to install brake light switch 2004 hyundai accent gl

You search Auto repair manual PDF about video how to install brake light switch 2004 hyundai accent gl, search results will appear below. If search results do not exist, please search by others keyword.

2000-2004 Audi TT Coupe Brake System

Filed Under (Audi) by admin on 31-12-2013

  Download 2000-2004 Audi TT Coupe Brake System

Download Audi TT Coupe 2000-2004, Audi TT Roadster 2001-2004 – Brake System. ABS/ESP ITT Mark 20 system components, removing and installing Brake light switch (square housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once. Removing – Remove storage compartment on driver’s side. Repair Manual, Body Interior, Repair Group 68; Storage compartments, covers – Unplug electrical connector. – Remove brake light switch -1- by turning counter-clockwise through 90. Installing Install in reverse sequence; note the following points: – Pull brake light switch plunger fully out. – Press brake pedal down as far as possible by hand. – Guide switch through installation hole and secure by turning 90 clockwise -arrows-. – Release brake pedal. – Make sure proper function of brake lights when brake pedal is pressed and released. Brake light switch (round housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once.… Read More

  Download 2000-2004 Audi TT Coupe Brake System

2003 Volvo S40 Replacing The Rear Brake Pads

Filed Under (Volvo) by admin on 29-12-2013

  Download 2003 Volvo S40 Replacing The Rear Brake Pads

Download 2003 Volvo S40 L4-1.9L Turbo VIN 27 B4204T4 Vehicle Level Brakes and Traction Control Disc Brake System Brake Pad Service and Repair Rear Brake Pads. Replacing The Rear Brake Pads Special Tools: 999 5782, 951 2834 General CAUTION: Replace the brake pads when the minimum thickness is 2 mm . Removing the rear brake pads Remove * the hub cap and the wheel * the retaining clip and the brake hose from the support * the upper bolt from the locating pin for the brake caliper . Twist the brake caliper backwards. Remove the brake pads. NOTE: Do not depress the brake pedal while the brake pads are removed. Checking and cleaning the rear brake calipers. Clean brake pad contact surfaces in the brake caliper and on the caliper mounting. Check the dirt guard for the piston. Replace the dirt guard if it is worn. Recondition the brake caliper if the dirt guard is defective.… Read More

  Download 2003 Volvo S40 Replacing The Rear Brake Pads

2007 Volkswagen Rabbit Brake pads, removing and installing

Filed Under (Volkswagen (VW)) by admin on 09-12-2013

  Download 2007 Volkswagen Rabbit Brake pads, removing and installing

Download 2007 Volkswagen Rabbit BRAKES Brake System. Brake pads, removing and installing Special tools, testers and auxiliary items required. Brake pads, removing When removing, mark brake pads that will be used again. Install in the same position, otherwise braking effect will be uneven! * Remove wheels. * Disconnect connector – 1 – for brake pad wear indicator. * Remove caps – arrows -. * Loosen both guide pins – arrows – and remove from brake caliper. * Remove brake caliper and secure with wire so that the weight of the brake caliper does not burden or damage the brake hose. * Remove brake pads from brake caliper. Cleaning: * Thoroughly clean contact surfaces for brake pads at brake carrier, remove corrosion. * Clean brake caliper. Use only appropriate solvents for cleaning brake caliper. Brake pads, installing Before pressing piston into cylinder using piston resetting tool, brake fluid must be extracted from brake fluid reservoir.… Read More

  Download 2007 Volkswagen Rabbit Brake pads, removing and installing

2004 Ford Expedition/Navigator Brake Pads REMOVAL AND INSTALLATION

Filed Under (Ford) by admin on 28-12-2013

  Download 2004 Ford Expedition/Navigator Brake Pads REMOVAL AND INSTALLATION

Download NOTE: Verify if the anchor housing spring has 1. CAUTION: Install a new lining if worn 1 end with 2 tabs. If yes, the LH side anchor to or past the specified thickness above the housing spring must be installed with the metal backing plate or rivets. Install new 2-tabbed end in the upper brake caliper cavity. pads in complete axle sets. For the LH brake caliper, release the lower If necessary, using a suitable suction device, portion of the anchor housing spring. remove the brake fluid in the master cylinder •Apply force at the center of the anchor reservoir until it is half filled. housing spring and pull outward at the bottom of the anchor housing spring to 2. Remove the wheel and tire assembly. For remove it from the lower brake caliper additional information, refer to Section 204-04. cavity. 3. Inspect the brake pads for wear or contamination.… Read More

  Download 2004 Ford Expedition/Navigator Brake Pads REMOVAL AND INSTALLATION

HONDA CRF-150 Installation Maintenance Instructions Guide

Filed Under (Honda) by admin on 20-01-2014

  Download HONDA CRF-150 Installation Maintenance Instructions Guide

Download Do not zip tie anything until you are done. Step1: Remove headlight, seat and gas tank. You may have to move the kill switch to the right side of the handlebars if you don’t have enough room on the left side. Step 2: Partially install the headlight assembly using the top right heavy-duty zip tie only to hold it in place temporarily. You will need to plug wires to this assembly and if you put all the bands on you will not be able to make the connections. Step 3: Install handlebar switch on clutch side. You will need to move clutch perch to the right (about ½ inch to 1 inch) to make room for the switch. The clutch adjuster should just miss the handlebar switch. The switch plugs into the circuit board on the bottom of the headlight using the 8-pin plug (the only unused 8-pin one on the circuit board) Step 4: With the front wheel turned all the way to the right, run all wires down the left side of the bike.… Read More

  Download HONDA CRF-150 Installation Maintenance Instructions Guide

Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery

Filed Under (Other Manuals) by admin on 26-12-2013

  Download Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery

Download Models: 2004 Buick Rainier 2000-2004 Cadillac Escalade 2002-2004 Cadillac Escalade EXT 2003-2004 Cadillac Escalade ESV 1998-2004 Chevrolet Blazer, S-10 Pickup 1999-2004 Chevrolet Silverado 2000-2004 Chevrolet Suburban, Tahoe 2002-2004 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2004 Chevrolet Express 1998-2004 GMC Jimmy/Envoy, Sonoma 1999-2004 GMC Sierra 2000-2004 GMC Yukon, Yukon XL 2002-2004 GMC Envoy, Envoy XL 2003-2004 GMC Savana 2004 GMC Envoy XUV 1998-2004 Oldsmobile Bravada 2003-2004 HUMMER H2. #04-06-03-002: Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery – (Feb 5, 2004) When diagnosing a concern regarding an intermittent vehicle no crank or dead battery, technicians should remove and reinstall the ignition switch using the Ignition Switch Replacement procedure in the Steering Wheel and Column section of SI. The ignition switch may have been misindexed in the steering column during a previous replacement . If the ignition switch is misindexed in one direction, the ignition switch circuits will not be completely open when the ignition switch is in the OFF position with the key removed.… Read More

  Download Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery

2004 F250 4×4 XLT Sport Crew Cab Super Duty Auxiliary Switch Install

Filed Under (Ford) by admin on 01-01-2014

  Download 2004 F250 4×4 XLT Sport Crew Cab Super Duty Auxiliary Switch Install

Download TOOLS & PARTS I USED – Carling illuminated rocker switch part number V1D2GHNB-AAC00-000 (three of these) – Carling illuminated rocker switch momentary part number V2D2GHNB-AAC00-000 – Round rocker switch – “attitude” switch found on ebay (two of these) – Carling 3-switch mount part number VM3-01 – Carling single switch mount part number VMS-01 – Ford Wiper Shaker system part number A8FCS-17526-A – Slim Line truck cap light (ebay) – superbrightleds.com part number WLED-WHP5 LED – inline 1/4″ x 1-1/4″ fuse holder – Radio Shack part number 270-1217 – inline blade type fuse holder – part number HHG (three of these) – SPDT Automotive Relay part number AZ9731-1C-12DC1 (two of these) – 20 amp blade type fuse
- 5 position terminal strip (two of these) – 4.5″ x 3.5″ x 1.5″ plastic enclosure – 10AWG wire (~10 feet) – 12AWG wire (several feet, various colors) – 16AWG wire (several feet, various colors) – 1N4001 diode – misc crimp terminals – Dremel tool & accessories – Cordless drill – 3/4″ wood drill bit – 1/8″ drill bit – soldering iron & solder – Xacto knife blade tip for soldering iron – Digital multimeter – Clamp-on DC ammeter – Handheld infrared thermometer – various sizes of heat shrink tubing – normal hand tools (wire strippers, cutters, crimpers, screwdrivers, etc) – socket set – Brother P-Touch label maker – 3/4″ label cartridge – black on white – 3/4″ label cartridge – black on clear PROCEDURE First, in order to accommodate these new circuits, I decided to upgrade the power availability in the cab.… Read More

  Download 2004 F250 4×4 XLT Sport Crew Cab Super Duty Auxiliary Switch Install

2000 Cadillac DeVille Brake Switch Circuit Low Input

Filed Under (Cadillac) by admin on 06-04-2014

  Download 2000 Cadillac DeVille Brake Switch Circuit Low Input

Download . Circuit Description The torque converter clutch (TCC) brake switch is used to indicate the status of the brake pedal (applied or released). If the PCM detects an open TCC brake switch (stuck ON) during accelerations, then DTC P0719 sets. DTC P0719 is a type C DTC. Conditions for Running the DTC * No VSS DTCs P0502 or P0503. * DTC P0719 has not passed this ignition cycle. Conditions for Setting the DTC The TCC brake switch input is at 0 volts for 15 minutes and the following conditions occur 8 times without a status change on the TCC brake input: * The vehicle speed is less than 8 km/h (5 mph). * The vehicle accelerates to 32 km/h (20 mph) within 2-6 seconds. * Then the vehicle speed remains above 32 km/h (20 mph) for 6 seconds. Action Taken When the DTC Sets * The PCM does not illuminate the malfunction indicator lamp (MIL).… Read More

  Download 2000 Cadillac DeVille Brake Switch Circuit Low Input

2008 HONDA CR-V FOG LIGHTS INSTALLATION INSTRUCTIONS

Filed Under (Honda) by admin on 09-12-2013

  Download 2008 HONDA CR-V FOG LIGHTS INSTALLATION INSTRUCTIONS

Download PARTS LIST Right fog light Left fog light Fog light harness Fog light switch harness Right trim Left trim Switch Relay Bracket 15Wire ties 4 Wire ties with clip 2 Tapes 8 Self-tapping screws, 5 x 16 mm. Washer bolt, 6 x 16 mm Flange nut, 6 mm Fuse (20A) TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver Flat-tip screwdriver Diagonal cutters Ratchet 10 mm Socket 10 mm Combination wrenches Hook tool Isopropyl alcohol Utility knife Masking tape. INSTALLATION 1. Make sure you have the anti-theft codes for the audio and navigation system (if equipped), and write down the XM radio presets (if equipped). 2. Disconnect the negative cable from the battery. 3. Remove the front bulkhead cover (seven clips). 4. Remove the front bumper (four self-tapping screws, six clips, and two bolts). 5. Remove the five clips from the left inner fender, and pull down the left inner fender. 6.… Read More

  Download 2008 HONDA CR-V FOG LIGHTS INSTALLATION INSTRUCTIONS

1995 Mazda MX-6 BRAKE SYSTEM REMOVAL & INSTALLATION

Filed Under (Mazda) by admin on 09-12-2013

  Download 1995 Mazda MX-6 BRAKE SYSTEM REMOVAL & INSTALLATION

Download 1. Raise and support front of vehicle. Remove front wheel assemblies. Remove lower lock pin/guide bolt. See Fig. 2 . Pivot caliper upward and support using rope. 2. Remove pads, shims, guide plates or pad guides and “V” springs (if equipped). Replace pad if lining thickness is less than specified. See MINIMUM PAD LINING SPECIFICATIONS (FRONT) table. 3. To install, reverse removal procedure. Use Disc Brake Expander (49-0221-600C) and an old pad to push piston fully inward to install disc pads. FRONT DISC BRAKE CALIPER Removal & Installation Raise and support front of vehicle. Remove front wheel assemblies and disconnect brake hose. Plug all openings. Remove front disc brake pads. See FRONT DISC BRAKE PADS . Remove remaining mounting bolt(s). Remove caliper from vehicle. To install, reverse removal procedure. Bleed air from system. FRONT BRAKE ROTOR Removal & Installation 1. Raise and support front of vehicle. Remove front wheel assemblies.… Read More

  Download 1995 Mazda MX-6 BRAKE SYSTEM REMOVAL & INSTALLATION

You might also likeclose