vacuum line to brake booster on 4 3 99 silverado

You search Auto repair manual PDF about vacuum line to brake booster on 4 3 99 silverado, search results will appear below. If search results do not exist, please search by others keyword.

2004+ Acura TSX Rear Big Brake Kit Installation Instructions

Filed Under (Acura) by admin on 09-12-2013

Download Step 1 Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels For a rear kit installation, block the front wheels, and release the parking brake. Then break loose the lug nuts on both rear wheels before jacking up the car. Refer to the Owner’s Manual to identify the correct location of the jack for raising the vehicle. Jack up the vehicle, and secure it on a pair of jack stands, again referring to the Owner’s Manual for jack location joints. After securing the vehicle at a convenient height, remove the rear wheels. Step 2 Disconnect Stock Brake Line Loosen the hard line fitting from the stock brake line, using a 10mm flare wrench. Place a drip tray or several rags directly below the inboard brake line connection. If the area around the brake line connection to the chassis is dirty, clean it using brake cleaner or an appropriate cleaning agent.… Read More

2004+ Acura TSX Front Axle Kit

Filed Under (Acura) by admin on 03-02-2014

Download Step 1 Raise Vehicle, and Remove Wheels For a front kit installation, apply the parking brake, then break loose the lug nuts on both front wheels before jacking up the car. Refer to the Owner’s Manual to identify the correct location of the jack for raising the vehicle. Jack up the vehicle, and secure it on a pair of jack stands, again referring to the Owner’s Manual for jack location joints. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. Note: All photographs show a left-hand side installation, unless otherwise noted. After securing the vehicle at a convenient height, remove the front wheels. Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake Note: To ensure safety, the parking brake must be applied before removing the front must be applied before removing the front must be applied before removing the front must be applied before removing the front must be applied before removing the front wheels.… Read More

2005 Chevrolet Malibu Service and Repair

Filed Under (Chevrolet (Chevy)) by admin on 09-12-2013

Download Vacuum Brake Booster Check Valve and/or Hose Replacement Removal Procedure 1. Disconnect the brake booster vacuum check valve (1) from the brake booster. 2. If the vacuum check valve (1) needs to be separated from the vacuum hose (3), release and reposition the clamp (2) on the vacuum hose (3) and remove the check valve (1) from the hose (3). 3. If replacing the vacuum check valve (1), remove the grommet (4) from the brake booster and discard the grommet. 4. If removing the vacuum hose (2), take note of the vacuum hose routing then disconnect from the engine intake manifold connection (3) by releasing tension on the vacuum hose clamp (1) and sliding the vacuum hose (2) off the intake manifold connection (3). Installation Procedure Important: A small amount of denatured alcohol can be used as an assembly aid when installing the vacuum check valve and/or grommet. Do NOT use soap.… Read More

2003 Volvo S40 Replacing The Rear Brake Pads

Filed Under (Volvo) by admin on 29-12-2013

Download 2003 Volvo S40 L4-1.9L Turbo VIN 27 B4204T4 Vehicle Level Brakes and Traction Control Disc Brake System Brake Pad Service and Repair Rear Brake Pads. Replacing The Rear Brake Pads Special Tools: 999 5782, 951 2834 General CAUTION: Replace the brake pads when the minimum thickness is 2 mm . Removing the rear brake pads Remove * the hub cap and the wheel * the retaining clip and the brake hose from the support * the upper bolt from the locating pin for the brake caliper . Twist the brake caliper backwards. Remove the brake pads. NOTE: Do not depress the brake pedal while the brake pads are removed. Checking and cleaning the rear brake calipers. Clean brake pad contact surfaces in the brake caliper and on the caliper mounting. Check the dirt guard for the piston. Replace the dirt guard if it is worn. Recondition the brake caliper if the dirt guard is defective.… Read More

2007 Volkswagen Rabbit Brake pads, removing and installing

Filed Under (Volkswagen (VW)) by admin on 09-12-2013

Download 2007 Volkswagen Rabbit BRAKES Brake System. Brake pads, removing and installing Special tools, testers and auxiliary items required. Brake pads, removing When removing, mark brake pads that will be used again. Install in the same position, otherwise braking effect will be uneven! * Remove wheels. * Disconnect connector – 1 – for brake pad wear indicator. * Remove caps – arrows -. * Loosen both guide pins – arrows – and remove from brake caliper. * Remove brake caliper and secure with wire so that the weight of the brake caliper does not burden or damage the brake hose. * Remove brake pads from brake caliper. Cleaning: * Thoroughly clean contact surfaces for brake pads at brake carrier, remove corrosion. * Clean brake caliper. Use only appropriate solvents for cleaning brake caliper. Brake pads, installing Before pressing piston into cylinder using piston resetting tool, brake fluid must be extracted from brake fluid reservoir.… Read More

2003 Hyundai Tiburon Front Big Brake Kit Manual Installation Instructions

Filed Under (Hyundai) by admin on 21-11-2013

Download
Hyundai Tiburon Front Axle Kit. Kit Contents Your StopTech Big Brake kit includes the following: 1 pair of ST-40 four-piston calipers, sized specifically for your vehicle 1 set of high-performance street pads (not suitable for track use) 1 pair of 328 X 28mm two-piece rotor assemblies 1 pair of aluminum caliper adapter brackets 2 pair of 7/16-20 self-locking Jet nuts 2 pair of 12mm washers 1 pair of stainless steel brake lines 1 pair of banjo bolts 2 pair of copper crush washer s 1 pair of rubber end caps.
Step 1 Raise Vehicle, and Remove Wheels : A level, stable and clean surface, suitable for supporting the vehicle on jack-stands, should be used for the installation. For a front kit installation, apply the parking brake, then break loose the lug nuts on both front wheels before jacking up the car. Refer to the Owner’s Manual to identify the correct location of the jack for raising the vehicle.… Read More

2004 Jeep Grand Cherokee Limited BODY & ACCESSORIES Speed Control

Filed Under (Other Manuals) by admin on 30-11-2013

Download 1. Disconnect vacuum hose at speed control servo and install a vacuum gauge into the disconnected hose. 2. Start engine and observe gauge at idle. Vacuum gauge should read at least ten inches of mercury. 3. If vacuum is less than ten inches of mercury, determine source of leak. Check vacuum line to engine for leaks. Also check actual engine intake manifold vacuum. If manifold vacuum does not meet this requirement, check for poor engine performance and repair as necessary. 4. If vacuum line to engine is not leaking, check for leak at vacuum reservoir. To locate and gain access to reservoir, refer to Vacuum Reservoir REMOVAL / INSTALLATION . Disconnect vacuum line at reservoir and connect a hand-operated vacuum pump to reservoir fitting. Apply vacuum. Reservoir vacuum should not bleed off. If vacuum is being lost, replace reservoir. 5. Verify operation of one-way check valve and check it for leaks.… Read More

1999 – 2002 Ford F-150 2WD and Ford Expedition Front Big Brake Update

Filed Under (Ford) by admin on 01-01-2014

Download Kit Contents Your StopTech Big Brake kit includes the following: 1 pair of ST-40 four-piston calipers, sized specifically for the vehicle 1 set of high-performance street pads (not suitable for track use) 1 pair of 355 X 32mm two-piece rotor assemblies 1 pair of aluminum caliper adapter brackets 2 pair of 7/16-20 self-locking Jet nuts 2 pair of 12mm washers 1 pair of hub assemblies 1 pair of stainless steel brake lines 1 pair of Adel clamps 1 pair of 10mm button-head bolts (for use with the Adel clamps) 1 pair of self-locking nuts (for use with the Adel clamps) 1 pair of banjo bolts 2 pair of copper crush washer s 1 pair of rubber end caps. Tools and Equipment Required Different models and years of vehicle use different-sized fasteners, and every effort has been taken to correctly identify the proper sized tool for each step of the installation.… Read More

2003 Honda Accord LX BRAKES Disc and Drum

Filed Under (Honda) by admin on 01-01-2014

Download Remove wheels. Thoroughly clean outside of caliper to prevent dust and dirt from entering inside. Support caliper with a piece of wire to prevent damage to brake hose. Remove 2 caliper bolts and caliper from bracket. Remove pad shims and pads. Using vernier calipers, measure the thickness of each brake pad lining. Measurement does not include pad backing plate thickness. See DISC BRAKE SPECIFICATIONS . Remove pad retainers. Inspection Clean caliper thoroughly; remove any rust, and check for grooves and cracks. Check brake disc for damage and cracks. Measure brake pad thickness. See DISC BRAKE SPECIFICATIONS . If brake pad thickness is less than service limit, replace pads as a set. Installation 1. Install pad retainers. Apply Molykote M77 compound onto pad side of shim. Wipe excess grease off shim. Keep grease off discs and pads. Install brake pads and shims. Install inner pad with its wear indicator facing downward.… Read More

Honda VTX 1800 Motorcycles Trike Conversion Installation Instruction

Filed Under (Honda) by admin on 12-12-2013

Download Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) . · Passenger Seat and mounts (to be reinstalled without modification) . NOTE: OEM front and rear seat mounting bolts to be retained and reused. · Left and right passenger foot rests and mounts (to be reinstalled with modification) . · Mufflers (to be re-installed and relocated with minor modification) . · Rear Fender (complete w/ sub frame and all attaching parts) . · Swing Arm, Drive Shaft and Rear Wheel (complete w/ brake line and all attaching parts) Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Use 17/64″ drill and drill through frame from inside out using passenger footrest mount holes as guide.… Read More

You might also likeclose