". You can read and download the PDF file on this page, or you can watch the video tutorial. Please use another keyword if these document aren't what you look for.
Paul T I have had similar issues with my dash ac over the past 8 years. Each time the cause was the same and easy to fix. The vacuum line to the vacuum motor on the.
parking brake on winnie itasca sunrise p30 chassis need to Question - parking brake on winnie itasca sunrise p30 chassis need to. Find the answer to this and.
i am making a bench wiring harness for a 8.1/allison MD setup for my RV i have the wiring diagram Workhorse R26 UFO Chassis 81L 2006 and this is the system i am.
Filed Under (Other Manuals) by Doe Namblas on 30-11-2013
Download 1. Disconnect vacuum hose at speed control servo and install a vacuum gauge into the disconnected hose. 2. Start engine and observe gauge at idle. Vacuum gauge should read at least ten inches of mercury. 3. If vacuum is less than ten inches of mercury, determine source of leak. Check vacuum line to engine for leaks. Also check actual engine intake manifold vacuum. If manifold vacuum does not meet this requirement, check for poor engine performance and repair as necessary. 4. If vacuum line to engine is not leaking, check for leak at vacuum reservoir. To locate and gain access to reservoir, refer to Vacuum Reservoir REMOVAL / INSTALLATION . Disconnect vacuum line at reservoir and connect a hand-operated vacuum pump to reservoir fitting. Apply vacuum. Reservoir vacuum should not bleed off. If vacuum is being lost, replace reservoir. 5. Verify operation of one-way check valve and check it for leaks.… Read More
Download 2004 Jeep Grand Cherokee Limited BODY & ACCESSORIES Speed Control
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 09-12-2013
Download Vacuum Brake Booster Check Valve and/or Hose Replacement Removal Procedure 1. Disconnect the brake booster vacuum check valve (1) from the brake booster. 2. If the vacuum check valve (1) needs to be separated from the vacuum hose (3), release and reposition the clamp (2) on the vacuum hose (3) and remove the check valve (1) from the hose (3). 3. If replacing the vacuum check valve (1), remove the grommet (4) from the brake booster and discard the grommet. 4. If removing the vacuum hose (2), take note of the vacuum hose routing then disconnect from the engine intake manifold connection (3) by releasing tension on the vacuum hose clamp (1) and sliding the vacuum hose (2) off the intake manifold connection (3). Installation Procedure Important: A small amount of denatured alcohol can be used as an assembly aid when installing the vacuum check valve and/or grommet. Do NOT use soap.… Read More
Download 2005 Chevrolet Malibu Service and Repair
Filed Under (Honda) by Doe Namblas on 01-01-2014
Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More
Download Honda Civic Racing Intake Manifold Installation Instruction
Filed Under (Ford) by Doe Namblas on 01-01-2014
Download 1998-2002 Continental FORD: 1998-2006 Town Car 1996-1999 Taurus SHO 2000-2006 LS 1998-2006 Crown Victoria, Mustang 1998-2006 Navigator 2000 Taurus 2002-2003 Blackwood 2002-2005 Thunderbird 2003-2005 Aviator 2003-2006 Focus 2004-2006 Taurus MERCURY: 2005-2006 Five Hundred, Freestyle 1998-2006 Grand Marquis 1997-2006 E-Series, Expedition, F-150 2000 Sable 1999-2006 F-Super Duty 2004-2005 Sable 2000-2005 Excursion, F-53 2005-2006 Montego 2001-2006 Escape 2002-2005 Mountaineer 2002-2005 Explorer 2005-2006 Mariner 2005-2006 Escape Hybrid 2006 Mariner Hybrid LINCOLN: 1997-1998 Mark VIII. This article supersedes TSB 04-16-01 to update the SERVICE PROCEDURE vehicle applications and model years. The optional WDS COP Kit available through NOTE Rotunda will provide more accurate diagnosis and help reduce replacement of non-defective parts. The FOLLOW THIS TSB PROCEDURE ONLY IF Kit (418-FS528) can be purchased through THERE ARE NO SPECIFIC MISFIRE TSBs/SSMs 1-800-ROTUNDA. RELEASED FOR THE VEHICLE SYMPTOM BEING EXPERIENCED. The following material will detail the diagnostic steps on WDS to take the guesswork out of misfire ISSUE diagnosis using the COP Kit.… Read More
Download WDS COP KIT DIAGNOSTIC TIPS COIL ON PLUG (COP) IGNITION SYSTEMS ENGINE MISFIRE OR ROUGH RUNNING
Filed Under (Ford) by Doe Namblas on 10-02-2014
Download Identifying Upper Intake Manifold Components (1 Of 3) (With Torque Specifications) Courtesy of FORD MOTOR CO. Item Specification Threadlock and Sealer TA-25 WSK-M2G351-A5. Removal All vehicles 1. Drain the cooling system. For additional information, refer to DRAINING . 2. Disconnect the battery ground cable. For additional information, refer to REMOVAL AND INSTALLATION . 3. Remove the air cleaner outlet pipe. For additional information, refer to REMOVAL AND INSTALLATION . 4. Remove the 4 transaxle roll restrictor cross brace bolts. 5. Remove the bolt and the transaxle roll restrictor cross brace. 6. Disconnect the evaporative emissions (EVAP) canister purge valve tube from the upper intake manifold and detach the retainer. 7. Disconnect the positive crankcase ventilation (PCV), brake booster and vacuum harness tubes from the upper intake manifold. 8. Detach the fuel tube retainer from the upper intake manifold. 9. Disconnect the exhaust gas recirculation (EGR) system module electrical connector and vacuum tube.… Read More
Download 2006 Ford Five Hundred SE UPPER INTAKE MANIFOLD
Filed Under (Honda) by Doe Namblas on 01-01-2014
Part # 307-05-0260 Racing Intake Manifold For Models and Years • 1992-1995 Honda Civic DX/EX (D15B7/D16Z6) • 1996-2000 Honda Civic EX (D16Y8) • 88-91 Honda CRX Si / DX* (*These models will require additional parts)
Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve).
Removal 1. Allow car to cool to ambient temperature. DO NOT attempt to work on warm or hot vehicle. 2. Drain coolant. 3. Relieve fuel pressure by loosening banjo bolt on top of fuel filter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced.… Read More
Download Honda Civic D-series Racing Intake Manifold Manual Installation Instructions
Filed Under (Ford) by Doe Namblas on 13-01-2014
Download What is an auxiliary input adapter ? An auxiliary input adapter is a vehicle specific device that connects to the radio’s CD Changer/DVD or Rear Seat Entertainment port and converts it to an audio input. With this auxiliary input installed you can connect and listen to any audio device (iPod, MP3, DVD, Sat Radio tuner etc) on the car speakers. The FRD04-AUX also features a built-in audio adjustment pot with 0 to +20dB input sensitivity range of 0.475 volts to 4.75 volts (peak to peak) which allows you to match the audio level of the Auxiliary device to that of the AM/FM Radio or CD. All Ford Compatible radios must have an “AUX” button and 16-pin “Phase II” radio connectors in the following vehicles: FORD LINCOLN 2007-08 Edge 2006-07 Mark LT 2007-08 Expedition 2007-07 MKX 2006-08 Explorer 2007-08 Navigator 2004 -08 F-150 2006 Zephyr 2005 -07 F-250 2005-07 F-350 2005-07 F-550 MERCURY 2005-08 Focus 2005-06 Montego 2005-0-7 Freestyle ² 2006-08 Milan 2005-06 Mustang 2006-08 Mountaineer 2007-08 Sport Trac.… Read More
Download 2004-Up AUXILLARY FORD INPUT ADAPTER INSTALLATION INSTRUCTION
Filed Under (Mercury) by Doe Namblas on 24-11-2013
Download 1. Remove the air cleaner outlet tube. 2. Remove the pin-type retainers and the accelerator cable splash shield. 3. Disconnect the throttle cable and the cruise control cable. 4. Disconnect the Throttle Position Sensor (TPS) and Idle Air Control (IAC) valve electrical connectors. 5. Disconnect the harness Tom the throttle body stud. 6. Disconnect the Exhaust Gas Recirculation (EGR) vacuum regulator and vacuum supply hoses. 7. Disconnect the Positive Crankcase Ventilation (PCV) and Evaporative Emissions (EVAP) vacuum hoses. 8. Remove the EGR valve. 1 Disconnect the vacuum hose. 2 Remove the nuts. 3 Remove the bolts. 4 Remove the EGR valve. 9. Remove the EGR Vacuum Regulator (EVR) valve. 1 Disconnect the vacuum hose. 2 Disconnect the electrical connector. 3 Remove the bolts. 4 Remove the valve. 10. Remove the eight bolts and the upper intake manifold. * Remove and discard the gaskets. * Clean all mating surfaces. Installation 1.… Read More
Download 2002 Mercury Sable Upper Intake Manifold
Filed Under (Honda) by Doe Namblas on 12-01-2014
Download STEP #1 Evacuate A/C system: • Have your local Air conditioning shop remove the HFC-134a refrigerant from your A/C system. They can reuse your coolant. After the supercharger installation you will need to return the car to them and have them refill and charge the system. This service should cost approximately $80.00. STEP #2 Remove ECM and ship to Hondata: • Remove the battery. • Remove ECM cover (A). • Remove bolts (D), then lift up the ECM. • Disconnect the ECM connectors A, B, and C. • Remove ECM and ship to Hondata (see Address to right.) STEP #3 Drain Coolant: • Jack up and support the front of the car on jack stands. • Make sure the engine is cool and remove the radiator cap. • Drain the cooling system by loosening the drain plug (A) at the bottom of the radiator. • Once all of the coolant is drained close the drain plug.… Read More
Download 2006 Honda Civic SI Comptech Supercharger Kit Installation Instructions
Filed Under (Honda) by Doe Namblas on 31-12-2013
Scottoiler: Honda CBF 1000 06- Installation Guide for Honda CBF 1000 06-
Locate the vacuum – There is a vacuum pipe from the fuel injector to cylinder no.1, as indicated below left. Cut into this pipe and insert the T-Piece from the Scottoiler kit. Then press the Damper Elbow, part number 4, onto the third leg of the tee. The RMV can be mounted under the seat, as shown in the third picture. The more vertical the RMV the better and remember to avoid exhaust and engine components. For further information, see our easy step installation guide – ‘RMV Positions, General’. The Dispenser Assembly, shown left, is routed along the underside of the Swingarm using Dispenser Mounting Sleeves, Cable Ties & Glue. Note: an epoxy resin (eg. Araldite) is req’d to bond the sleeves to the Swingarm. For further information see our easy step installation guide – ‘Dispenser Assemblies, General’ .… Read More
Download 2006 Honda CBF 1000 Manual Installation Instructions