transmission and shift lever diagram for a 91 civic manual

You search Auto repair manual PDF about transmission and shift lever diagram for a 91 civic manual, search results will appear below. If search results do not exist, please search by others keyword.

Ford C-4 Bracket and Lever Installation Instructions

Filed Under (Ford) by admin on 01-09-2012

Download STEP 1. Raise and safely support the vehicle at least 1-2 feet off the ground. Remove the nut and lock- washer holding the downshift linkage onto the downshift lever shaft. The downshift lever is the outer lever on C-4 transmissions. Pull the lever off the shaft and allow the linkage to hang free. Remove and discard stock shift linkage rods. Late C-4 transmissions have a Neutral safety/Backup light switch on the transmission shift lever. If your transmission is so equipped, remove the two bolts holding the switch in place and slide it off the shift shaft. Disconnect the switch at the factory plug and discard it. STEP 2. Install the B&M selector lever, See figure 1 . Note: The B&M lever must point downward for proper operation. If the stock shift lever on your transmission points down, you will have to remove the lower part of the stock arm by cutting it off to clear the B&M lever, (See figure 1 ) .… Read More

2002 Chrysler 300M Special GEAR SHIFT CABLE – FLOOR / REMOVAL

Filed Under (Chrysler) by admin on 10-12-2013

Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Filed Under (Other Manuals) by admin on 01-01-2014

Download Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) #05-07-30-031: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) – (Nov 11, 2005) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case.… Read More

1995 Ford Scorpio Transmission Range Sensor Installation Instructions

Filed Under (Ford) by admin on 01-01-2014

Download Remove 1. Move the selector lever to position “N”. 2. Raise the vehicle. 3. Unhook the loops for the rear exhaust pipe. 4. Detach the front heat shield and slide it backwards. 5. Detach the bracket for the front exhaust pipe from the transmission crossmember and swivel it downwards. NOTE: Support the automatic transmission with a transmission jack. 6. Detach the transmission crossmember. 1Detach it from the body. 2Detach it from the automatic transmission. Lower the automatic transmission and remove the transmission jack. 7. Detach the selector lever. 1Unclip the link rod from the selector lever. 2Selector lever 3Nut 4Selector shaft. 8. Disconnect the plug of the TR switch and remove the TR switch. Install NOTE: The guide of the TR switch must engage with the groove of the selector shaft. 9. Install and adjust the TR switch. NOTE: Do not tighten the bolts. 1Attach the TR switch. 2Slide on the selector lever and turn the selector shaft anti-clockwise as far as the stop.… Read More

1980-1992 Ford AOD Shift Improver Kit Installation Instructions

Filed Under (Ford) by admin on 01-01-2014

Download IMPORTANT: We recommend that you read through the instructions completely before beginning the installation so you can familiarize yourself with the installation procedure and tools required. Check the tool list at the end of these instructions for the tools required to install your B&M AOD Shift Improver Kit. Installation of the B&M AOD Shift Improver Kit can be accomplished by anyone with minimum mechanical experience. It is however, important to closely follow the instructions. Read each step carefully before proceeding, if you do not understand, go back and read the step again. NOTICE: The B&M AOD Shift Improver Kit is not a cure-all for an ailing transmission. If your transmission is slipping, chatters or is in poor general shape, the installation of this Shift Improver Kit may worsen the condition. However on a properly operating transmission in average condition, the B&M AOD Shift Improver Kit will provide the kind of transmission performance you are looking for.… Read More

Honda Civic D-series Racing Intake Manifold Manual Installation Instructions

Filed Under (Honda) by admin on 01-01-2014

Download
Part # 307-05-0260 Racing Intake Manifold For Models and Years • 1992-1995 Honda Civic DX/EX (D15B7/D16Z6) • 1996-2000 Honda Civic EX (D16Y8) • 88-91 Honda CRX Si / DX* (*These models will require additional parts)
Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve).
Removal 1. Allow car to cool to ambient temperature. DO NOT attempt to work on warm or hot vehicle. 2. Drain coolant. 3. Relieve fuel pressure by loosening banjo bolt on top of fuel filter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced.… Read More

1988 Jeep Cherokee Clutch Hydraulic Installation Guide

Filed Under (Jeep) by admin on 02-01-2014

Download
REMOVAL & INSTALLATION TRANSMISSION Removal 1) Remove the shift knob and lock nut from transmission and transfer case shift levers (if equipped). On Wrangler models, remove screws attaching transmission and transfer case shift lever boots and remove both boots. 2) On all other models, raise outer gearshift lever boot and remove upper part on center console. Remove lower part of console, remove inner boot and gearshift lever. 3) On Wrangler models, remove transmission shift tower dust cover. Remove transmission shift lever and stub shaft. DO NOT remove shift lever from stub shaft. 4) On all models, raise and support vehicle. Drain transmission lubricant. Mark rear drive shaft for reassembly and remove rear drive shaft. Support transmission assembly and remove crossmember. Disconnect speedometer cable and wiring from back-up light switch. 5) On 4WD models, drain transfer case lubricant. Disconnect transfer case vacuum hoses and linkage. Tag vacuum hoses for reassembly. Disconnect front drive shaft and secure out of way.… Read More

AEM V2 Air Intake System Manual Installation Instructions

Filed Under (Honda) by admin on 14-12-2013

Download
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6001
1992-1995 HONDA Civic SI L4-1.6L C.A.R.B.E.O. #D-670
1992-1995 HONDA Civic LX L4-1.5L Manual Trans. C.A.R.B.E.O. #D-670
1994-1995 HONDA Civic EX L4-1.6L Manual Trans. C.A.R.B.E.O. #D-670
1992-1995 HONDA Civic DX Hatchback L4-1.5L Manual Trans. C.A.R.B.E.O. #D-670
1992-1995 HONDA Civic DX L4-1.5L Manual Trans. C.A.R.B.E.O. #D-670
1992-1993 HONDA Civic L4-1.6L Manual Trans. C.A.R.B.E.O. #D-670
1. Preparing Vehicle a. Make sure vehicle is parked on level surface. b. Set parking brake. c. If engine has run in the past two hours, let it cool down. d. Disconnect all negative battery terminals. e. Raise the front of the vehicle with a jack. Refer to your owner’s manual for proper jack and jack stand placement to properly support vehicle. Support your vehicle using properly rated jack stands before wheel removal or while working under the vehicle. NEVER WORK UNDER A VEHICLE WITHOUT USING JACK STANDS.… Read More

Audi A4 B6/8E 5 Speed Short Shifter Installation Manual

Filed Under (Audi) by admin on 21-12-2013

Download A. Required Tools Safety Glasses (! See Warnings!) Circlip Pliers Hose Clamp Cutter Razor Blade Ratchet 3/8 or 1/4 Inch Drive Sockets Metric 3/8 or 1/4 Drive (7mm & 10mm) Extension Medium Length 3/8 or 1/4 Inch Drive 6mm Allen Key 6mm Allen Socket 2.5mm Allen key (Included in kit) T-25 Torx Driver 10mm Wrench 24mm or Adjustable Wrench. Step 1: Removal of console cover plate and shift knob. To remove the cover plate, open the ashtray and pull up on the front of the cover. Do the same for the rear of the cover by lifting from within the shift boot at the rear side. To remove the shift knob you must cut the clamp holding the shift knob we have included a new one in the kit. (! Safety glasses are required while cutting the hose clamp!) Once you have removed the clamp, pull up on the shift knob to remove it.… Read More

Checking oil level in automatic transmission and adding oil

Filed Under (Other Manuals) by admin on 28-03-2014

Download TRANSMISSION 722.700 in MODEL 168.031 /032 /033 /131 /132 /133 TRANSMISSION 722.701 in MODEL 168.006 /007 /008 /009 /109 TRANSMISSION 722.702 in MODEL 168.035 /135 TRANSMISSION 722.750 /751 in MODEL 414.700. Adding transmission oil Risk of accident. Secure vehicle to prevent it from moving. AS00.00-Z-0005-01A Danger! Accidents may result if the vehicle starts off unintentionally with the Wear closed and snug-fitting work clothes. engine running. Risk of injury. Do not grasp hot or rotating parts. Crushing and burn injuries may result while working on engine during when it is being started or when it is in operation. 1 Remove locking pin (1) To do this, break off the plate on the locking pin using a suitable tool and press out the remaining pin in the cap downwards 2 Remove cap (2) 3 Fill with transmission oil The vehicle must be horizontal. Transmission oil (ATF) in accordance with BB00.40-P-0236-10A Specifications for Operating Fluids, sheet no.… Read More

You might also likeclose