transfer case shifter 72 chevy exploded view

You search Auto repair manual PDF about transfer case shifter 72 chevy exploded view, search results will appear below. If search results do not exist, please search by others keyword.

2000 Chevy Truck S10/T10 Transfer Case Replacement

Filed Under (Chevrolet (Chevy)) by admin on 28-11-2013

Download 2000 Chevy Truck S10/T10 Blazer 4WD V6-4.3L VIN W Vehicle Level Transmission and Drivetrain Transfer Case Service and Repair NVG 233/243-NP1 Transfer Case Replacement. Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 7. Remove any wiring harness from the transfer case. 8. Support the transfer case with a transmission jack. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case. 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case.… Read More

Ford Focus Short SVT M-7210-S Throw Shifter INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 27-11-2013

Download REMOVING THE CONSOLE STEP 1: Remove the front cup holders. Remove the Torx screws under the cup holder with a T-20 bit. (Some cars may have Phillips head screws). STEP 2: Remove the rear cup holders. Squeeze the center and pull forward to undo the back tab, then pull straight up to unsnap the cup holder. Remove the nuts holding the rear of the console. STEP 3: Unscrew the shift knob from the shifter. Leave it attached to the leather boot. STEP 4: Pull the parking brake up as far as it will go. STEP 5: Pull up and back to remove the console. Be careful not to scrape the brake handle on the console. STEP 6: Reach underneath the console and disconnect the cigarette lighter plug. REMOVING THE STOCK SHIFTER STEP 7: Place the transmission in 1st gear. Steady the shift lever with one hand and pry the cable off with a screwdriver.… Read More

Service 4WD Light Illuminated, DTC C0374 Set (Inspect Wiring Harness to Transfer Case Speed Sensors, Replace Wiring Harness)

Filed Under (Other Manuals) by admin on 01-01-2014

Download Models: 2004-2007 Buick Rainier 2003-2006 Chevrolet Avalanche, Suburban, Tahoe 2003-2007 Chevrolet Silverado Classic, TrailBlazer, TrailBlazer EXT 2003-2006 GMC Yukon, Yukon XL 2003-2007 GMC Envoy, Envoy XL, Sierra Classic 2003-2004 Oldsmobile Bravada 2005-2007 Saab 9-7X with Four Wheel Drive or All-Wheel Drive and Active All-Wheel Drive (RPO NP4) or Active Two-Speed (RPO NP8) Transfer Case. Condition Some customers may comment on intermittent illumination of the Service 4WD light. Upon investigation, the technician may find DTC C0374 set. The customer may also comment on intermittent erratic operation of the 4WD or AWD system after driving through rain/snow or simply going through a car wash. Cause The speed sensor signal may have become corrupted. Possible openings in the speed sensor wire insulation (twisted pairs) can allow water intrusion. Also, wire connections contaminated by water may result in short circuits and erroneous speed sensor readings. This most often occurs on the rear speed sensor circuit.… Read More

1995-1997 FORD EXPLORER TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS

Filed Under (Ford) by admin on 12-02-2014

Download FORD: 1995-1997 EXPLORER 2. Connect the New Generation Star (NGS) Tester ISSUE to the Data Link Connector (DLC) underneath The diagnostic procedure for binding or shudder the steering wheel. Monitor for any Diagnostic from transfer case in slow, tight turns while in 4 Trouble Codes (DTCs) set by the transfer case Auto mode may be inaccurate for some vehicles. that could indicate incorrect speed sensor function. Codes could include, but are not ACTION limited to: Diagnose transfer case binding or shudder concerns using the following Diagnostic Procedure. •P1836 – Front propshaft sensor circuit failure •P1837 – Rear propshaft sensor circuit failure DIAGNOSTIC PROCEDURE •P1874 – Hall effect sensor power short circuit to battery 1997 EXPLORER •P1875 – Hall effect sensor power circuit 1. Test drive the vehicle in 4 Auto, 4 High and 4 failure Low. Evaluate the vehicle in each of these NOTE modes. The vehicle should bind in turns in both ADDITIONAL CODES COULD BE SET AS WELL.… Read More

Various Concerns with Shifter and/or Ignition Key

Filed Under (Other Manuals) by admin on 28-02-2014

Download Models: 2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) Condition Some customers may comment on any of the following concerns: Cause 1 The shifter button may be sticking in the handle. Cause 2 The pin that activates the micro-switch may have moved out of position (refer to illustration above). This causes the micro-switch to fail to engage when the vehicle is placed in Park. If this condition is present, the customer will not be able to remove the key from the ignition. The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter
assembly moves when activating the button.… Read More

1990-1993 Acura Integra TWM Performance Short Throw Shifter Installation Manual

Filed Under (Acura) by admin on 12-02-2014

Download 1. Unscrew the stock shift knob by rotating it counter clockwise. 2. Remove all screws securing center console and remove console. 3. Remove the rubber dust boot surrounding the shifter, use caution not to damage it. Put it in a safe place for re-installation later. 4. Place the car up on a lift, or use a jack and jack stands to raise it off the ground. Loosen the nut on the base of the shifter using a 12mm socket and ratchet. You may need to hold the head of the bolt on the opposite side of the shift rod with a wrench to loosen the nut. 5. Remove the bolt from the base of the shifter and lower the shift rod that connected it to the shifter. 6. Remove both bolts securing the shift assembly to the under side of the chassis with a 12mm socket and ratchet. 7. Remove the bolt at the transmission end of the shift rod with a 12mm or 14mm (depending on model) socket and ratchet.… Read More

1988 Jeep Cherokee Clutch Hydraulic Installation Guide

Filed Under (Jeep) by admin on 02-01-2014

Download
REMOVAL & INSTALLATION TRANSMISSION Removal 1) Remove the shift knob and lock nut from transmission and transfer case shift levers (if equipped). On Wrangler models, remove screws attaching transmission and transfer case shift lever boots and remove both boots. 2) On all other models, raise outer gearshift lever boot and remove upper part on center console. Remove lower part of console, remove inner boot and gearshift lever. 3) On Wrangler models, remove transmission shift tower dust cover. Remove transmission shift lever and stub shaft. DO NOT remove shift lever from stub shaft. 4) On all models, raise and support vehicle. Drain transmission lubricant. Mark rear drive shaft for reassembly and remove rear drive shaft. Support transmission assembly and remove crossmember. Disconnect speedometer cable and wiring from back-up light switch. 5) On 4WD models, drain transfer case lubricant. Disconnect transfer case vacuum hoses and linkage. Tag vacuum hoses for reassembly. Disconnect front drive shaft and secure out of way.… Read More

1994 Chevy Truck C 1500 Ignition – Timing Connector Location Change

Filed Under (Chevrolet (Chevy)) by admin on 07-02-2014

Download 1994 Chevy Truck C 1500 Truck 2WD V6-262 4.3L VIN Z Vehicle Level Maintenance Tune-up and Engine Performance Checks Ignition Timing Technical Service Bulletins Ignition – Timing Connector Location Change. INFORMATION SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1).… Read More

2010 Hyundai Genesis Coupe Short Shifter Manual Installation Instructions

Filed Under (Hyundai) by admin on 22-02-2014

Download
Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged to install the short shifter on a slightly inclined surface, place wooden blocks in front or behind the wheels to prevent the car from moving while you’re working. Please read this installation manual completely before installing the short shifter. Make sure to let the car cool down before you do the install as you will be working on and around the exhaust line.
INSTALLATION INSTRUCTIONS: 1. Working inside the car, unsnap the shift boot from the shift knob and remove the shift knob by rotating it counter clockwise. Put it aside in a safe place for re-install later. 2. With your fingers inside the shift boot, pull the shifter console up. 3. If you have heated seats, unplug the connector from the console.… Read More

Audi S4/A6 Biturbo Short Shifter Installation Instructions

Filed Under (Audi) by admin on 26-03-2014

Download included in this package: – Shifter – Shift Linkage Bracket The following tools are recommended for installation: • ¼” ratchet • 10mm open end/box end wrench • 10mm socket • 3/8″ open end/box end wrench • 3/8″ socket or a 2nd 3/8″ box end wrench • flexible plunger-type four-claw retriever • socket wobble (universal joint) attachment • 1/8″ allen hex key wrench • socket extension • 6mm allen socket head bit • snap ring / circlip pliers Installation Tips Familiarizing yourself with the short shifter pieces will help make the installation process very easy. Take the time to study each of the pieces that make up the short shifter and read through the installation instructions before you begin. Step 1 – Remove shift knob Unscrew the shift knob from the original lever. Step 2 – Remove shift boot Pry up the edges of the shift boot with fingertips, remove from console.… Read More

You might also likeclose