torque spec for 2006 ford escape wheel bearing

You search Auto repair manual PDF about torque spec for 2006 ford escape wheel bearing, search results will appear below. If search results do not exist, please search by others keyword.

1997 Ford Aerostar/Ranger Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive DISASSEMBLY AND ASSEMBLY

Filed Under (Ford) by admin on 11-12-2013

Download Wheel Grease Seal and Bearing, Front Replacement and Repacking SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Impact Slide HammerT50T-100-A Bearing Cup ReplacerT80T-4000-P Driver Handle T80T-4000-W Seal Replacer T80T-4000-T Spindle Seal ReplacerT95T-3132-D. The recommended wheel bearing lubricant is lithium-base High-Temperature Constant Velocity Joint Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. -base grease is not compatible with lithium-base grease. Do not intermix. Clean all old lubricant grease prior to lubricating front/rear wheel bearing. Use of incompatible bearing lubricant could result in premature lubricant breakdown. NOTE: If bearing adjustment does not eliminate looseness or rough and noisy operation, clean, inspect and repack the hub and wheel bearings with specified wheel grease. If wheel bearing cup or the cone and roller assemblies are worn or damaged, they should be replaced. Manual Locking Hub, Ranger. Disassembly 1. Raise the vehicle and install Rotunda Car/Truck Stands 077-00018 or equivalent. 2. Remove the wheel and tire assembly.… Read More

2000-2005 Ford Explorer Wheel Bearings REMOVAL & INSTALLATION

Filed Under (Ford) by admin on 17-01-2014

Download 1. Before servicing the vehicle, please familiarize yourself with safety procedures. 2. Remove the axle”to”wheel hub retainer nut and washer. 3. Remove the parking brake shoes. 4. Press the outboard CV”joint until it is loose from the hub. 5. Remove and discard the toe link”to”wheel knuckle nut. 6. Remove the bolt and separate the toe link from the wheel knuckle. 7. Remove and discard the upper arm”to”wheel knuckle nut. 8. Remove the bolt and separate the upper arm from the wheel knuckle. 9. Remove and discard the lower arm”to”wheel knuckle nut. 10. Remove the lower arm”to”wheel knuckle bolt. 11. Remove the wheel knuckle. 12. Using a suitable press, remove and discard the wheel hub. 13. Remove and discard the wheel bearing retainer ring. 14. Using a suitable press, remove the wheel bearing. Fig. Rear hub/bearing Assembly”Aviator, Explorer and Mountaineer Fig. Pressing out the bearing 1. Installation is the reverse of the removal procedure.… Read More

2000 BMW 528i (E39) Front Wheel Bearing

Filed Under (BMW) by admin on 31-12-2013

Download 2000 BMW 528i (E39) L6-2793cc 2.8L DOHC (M52 TU) Vehicle Level Steering and Suspension Wheels and Tires Wheel Bearing Service and Repair Front Wheel Bearing. Replacing Front Wheel Bearing ( Wheel Hub )(Basis) Caution! Bearing cannot be dismantled. Do not wash out bearings. Remove brake disk (brake line remains connected), refer to Brakes and Traction Control; Disc Brake System. Remove ABS impulse sensor. Remove stabilizer link from stabilizer, Steering and Suspension. Unfasten nut. Installation: Use washer (1). Tapered spigot and bore both free of grease. Replace self-locking nut. Brace on hexagon socket if necessary. Tightening Torque, refer to Steering Specifications. Press off track rod with special tool 31 2 240. Mark the installation position of the spring strut tube (1) in the swivel bearing (2) with paint – never mark with scribing tool. Marking is not required if the factory mark is still identifiable. R installation position of right spring strut tube L installation position of left spring strut tube Version with factory marking above the swivel bearing.… Read More

COMP Cams® Ford Timing Set Installation Instructions

Filed Under (Ford) by admin on 09-12-2013

Download Ford Timing Set Installation Instructions Thank you for choosing COMP Cams® products! We know you have options in valve train component selection and we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and also take a moment to review the included limited warranty information. Engine Application High Energy Magnum Hi-Tech Ford V6, 144-200 3223 Ford V6, 171 (2600-2800cc) 3236 Ford V8, 255, 289, 302 & Boss 302, 1965-1988 2120 3120 Ford V8, 289-351W & Boss 302, pre 1972 3220 Ford V8, 302-351W, 1972 & up 3230 Ford V8, 352-428, 1964-1974 3208 2108 3108 Ford V8, 351C, 351M, 400M, 1970-1982 3221 2121 3121 Ford V8, 429-460, 1968-1971 3222 2122 3122 Ford V8, 429-460, 1972-1987 2130 3130 Ford V8, 429-460 w/nine keyway crank gear 2134* Ford V8, 351W, 351W H.O., 1969-¹84 2135 3135 Ford V8, 5.0L 302 H.O., 1980-March 21, 1984 2131 3131 Ford V8, 5.0L 302, 351W, March 22, 1984-1992 2138 3138 Notes: * #2120 or #3120 should not be installed on 351W engines as they are designed for 255, 289, 302 or Boss 302 engines.… Read More

Honda 400EX Wheel Hub Manual Installation Instructions

Filed Under (Honda) by admin on 19-12-2013

Download
Please follow these installation instructions carefully! Without proper installation, premature wear and failure can occur! 1. Remove all contents from its packaging and verify that all parts are present and free from damage. You should have the following items: (2) wheel hubs (2) smaller tapered bearings (2) large tapered bearings (2) wheel bearing nuts (2) dust caps (2) inner bearing seals (6) M3 x .5 screws (2) cotter pins (2) inner bearing spacers 2. Completely remove the old hubs from your quad and clean the spindle and the surrounding areas. It is very important to keep the new bearings and seals clean during installation for long life. Be sure to remove the factory inner bearing spacers from the spindle and discard. They will not be used in re-assembly. 3. Pack your new Timken tapered wheel bearings with a liberal amount of high quality wheel bearing grease. A wheel bearing packer works best, however you can accomplish the task by placing the grease in the palm of your hand and manually working it in between the bearing rollers.… Read More

2005-2008 Ford Escape TIRE WHEEL RUNOUT AND BALANCE

Filed Under (Ford) by admin on 28-02-2014

Download FORD: LINCOLN: 2005 Excursion, Explorer Sport Trac 2005-2008 Navigator 2005-2008 Escape, Expedition, Explorer, 2006-2008 Mark LT F-150, F-Super Duty, 2007-2008 Explorer Sport Trac, Ranger MERCURY: 2006-2008 F-53 Motorhome Chassis 2005-2008 Mariner, Mountaineer. SERVICE PROCEDURE FURTHER DIAGNOSIS OR REPAIRS SHOULD BE The following revisions have been made. The road PERFORMED. test has been simplified to include 15 minutes of 3. If tire and wheel vibration persists after the 15 driving rather than a 20 mile test drive. The minute road test, then complete wheel and tire requirement to bring an assistant along on the road radial run-out / Road Force® component test in test has been eliminated. Recordings should be the WSM, Section 204-04 to match mount made using the vibration analyzer and then review and/or balance tire and wheel assemblies. recordings following the test drive. The step to inspect the Integrated Wheel Ends (IWE) has also NOTE been eliminated. THE MATCH MOUNTING PROCEDURE IS MORE 1.… Read More

FORD LIMITED SLIP DIFFERENTIAL INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 11-01-2014

Download -IMPORTANT LUBRICANT NOTE- The Auburn Gear limited-slip differential design has been extensively tested with high quality non-synthetic 80W90 hypoid oils treated with GM or Ford friction additives (3 oz. of additive will treat 1 quart of oil). To avoid differential clutch chatter (noise) and for optimum performance, use the oil and additive described above. Use of other additive and oil types may cause differential clutch chatter. Ford Part Number: C8A219B546A GM Part Number: 1052358 PINION SHAFT MODIFICATION Certain “C” clip axle applications with high gear ratios will require pinion shaft modification due to the thickness of the ring gear. The thick ring gear will prohibit the pinion shaft from being removed making “C” clip installation impossible. Use the following procedure to modify the pinion shaft. 1. Modification to be 90º to the pinion shaft lock screw hole as shown. It is recommended that this be accomplished through grinding. 2. Remove sharp edge from modified section by buffing.… Read More

Honda 400EX Hub installation instructions

Filed Under (Honda) by admin on 28-12-2013

Download
Thank you and congratulations !!!!! You have purchased the best wheel hub available for your Honda 400EX. With careful installation and a regular maintenance schedule, these will be the last set of hubs that you will ever need to buy. Please follow these installation instructions carefully! Without proper installation, premature wear and failure can occur! 1. Remove all contents from its packaging and verify that all parts are present and free from damage. You should have the following items: (2) wheel hubs (2) smaller tapered bearings (2) large tapered bearings (2) wheel bearing nuts (2) dust caps (2) inner bearing seals (6) M3 x .5 screws (2) cotter pins (2) inner bearing spacers 2. completely remove the old hubs from your quad and clean the spindle and the surrounding areas. It is very important to keep the new bearings and seals clean during installation for long life. Be sure to remove the factory inner bearing spacers from the spindle and discard.… Read More

2009 Honda CR-V 17″ ALUMINUM WHEEL INSTALLATION INSTRUCTIONS

Filed Under (Honda) by admin on 15-12-2013

Download PARTS LIST Aluminum wheel (The illustration may differ from the actual wheel.) Wheel center cap (The illustration may differ from the actual center cap.) Center cap emblem 2 Push nuts Wheel cleaning information TPMS Information (Give this information to your customer.) Parts for TPMS sensor assembly Tire pressure sensor assembly Washer Valve cap Valve nut TOOLS AND SUPPLIES REQUIRED Ratchet wrench 11 mm Socket Torque wrench Isopropyl alcohol Shop towel HDS TPMS sensor initializer tool AKS0620006 INSTALLATION NOTE: •This aluminum wheel is designed for use on TPMS (Tire Pressure Monitoring System) vehicles. •This aluminum wheel is equipped with the TPMS sensor. See the Service Manual for tire replacement procedure and TPMS sensor installation procedure. •The illustration of the aluminum wheels shown are for reference purposes only. •Install the correct size tire. •Use a tire changer to remove and install the tires. Using a tire lever to remove and install the tires can damage the tire, the wheel, and the TPMS sensor.… Read More

2000 Ford F-150 Rear Drive Axle/Differential

Filed Under (Ford) by admin on 01-01-2014

Download 1. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the RH kick panel area. Failure to do so can result in unexpected inflation or deflation of the air springs, which can result in shifting of the vehicle during these operations. Raise and support the vehicle. 2. Remove the wheel and tire assembly. 3. Remove the differential housing cover (4033). ? Drain the lubricant. For additional information, refer to Differential Housing Cover in this section. 4. Remove the brake calipers and discs. 5. Remove the differential pinion shaft (4211). 1. Remove and discard the differential pinion shaft lock bolt. 2. Remove the differential pinion shaft. 6. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers (4N237). 1.… Read More

You might also likeclose