". You can read and download the PDF file on this page, or you can watch the video tutorial. Please use another keyword if these document aren't what you look for.
MY TRANSMISSION JUST WONT GO IN..AM I NOT SEEING SOMETHING??? COMPLAINT - TORQUE CONVERTER DOESNT SEAT PROPERLY IN TRANSMISSION MAKING IT IMPOSSIBLE TO.
what are the torque specs for head bolts for 2000 ford explorer 4.0l v6 over head cam.
Ford Explorer Torque Converter and Flex Plate R&R - YouTube justhes.
Filed Under (Ford) by Doe Namblas on 06-02-2014
Download REMOVAL Step 1 Before you begin – let vehicle cool for about an hour. Disconnect battery. Raise vehicle and support on jack stands. The higher you raise it, the easier it is to work under. If your installing a new transmission and converter, skip to STEP 3 Step 2 Drain oil from transmission by removing the drain plug. This is a good time to install a TCI® Drain Plug Kit, TCI® #805800. Pans without plug must be slowly removed by freeing one end and allowing bolts on other end to hold pan. The pan will drop down to allow the fluid to run out the end. Use a drain pan to catch fluid. Remove remainder of bolts and slowly lower pan and pour remainder of fluid in drain pan. Replace filter and clean pan and install new pan gasket. (New gaskets and filters available from TCI®). Reinstall pan and torque pan bolts to OEM specs.… Read More
Download FORD TORQUE CONVERTER & TRANSMISSION Installation Instructions
Filed Under (Ford) by Doe Namblas on 15-03-2014
Download (1) Pre-installation instructions; Disconnect Battery terminal, inspect and check transmission coolant lines for damage, flush lines and coolant system thoroughly. (2) Inspect crank well for converter hub wear, and clean this area. (3) Check Flywheel for cracks and converter bolt holes for wear. (4) Inspect back of engine block where transmission mates, ensure block is clean, no wires or cables are in the way of installation. (5) Inspect and verify both dowel pins are clean and secure in block. (6) Ensure Block Plate is aligned and straight. (7) Clean area of block so transmission can make a good ground. “Warning” Transmission will suffer permanent damage if grounded improperly! Installation : (1) Transmission Fluid: you need about 10 to 12 quarts of fluid for installation, Dextron III with Mercon, 1968 – 1993 Vehicles and Mercon 5, 1994 and Newer, any brand name. (2) If transmission was purchased with a torque converter from Monster Transmission & Performance, no need to follow step (3).… Read More
Download FORD TRANSMISSION INSTALLATION INSTRUCTIONS
Filed Under (Ford) by Doe Namblas on 31-12-2013
Please Note : The following instructions were made to act as a guide/reference, if you are inexperienced with performing an automatic transmission installation it is highly recommended that you contact a certified experienced professional to perform the installation and/or make the proper adjustments for you! Instructions : (1) Pre-installation instructions; Disconnect Battery terminal, inspect and check transmission coolant lines for damage, flush lines and coolant system thoroughly. (2) Inspect crank well for converter hub wear, and clean this area. (3) Check Flywheel for cracks and converter bolt holes for wear. (4) Inspect back of engine block where transmission mates, ensure block is clean, no wires or cables are in the way of installation. (5) Inspect and verify both dowel pins are clean and secure in block. (6) Ensure Block Plate is aligned and straight. (7) Clean area of block so transmission can make a good ground. “Warning” Transmission will suffer permanent damage if grounded improperly!… Read More
Download MONSTER TRANSMISSIONS : FORD TRANSMISSION INSTALLATION INSTRUCTIONS
Filed Under (Ford) by Doe Namblas on 15-02-2014
Download Part # 22907 1998 – 2001 Ford Explorer 4WD 1998 – 2007 Ford Ranger / Explorer Sport Trac Edge / Mountaineer 4WD Torsion bar key front leveling kit Part# Description Qty. 22907-01 Torsion bar keys 2 22907INST Instruction manual (customer copy) 1 22907INST Instruction manual (installer copy) 1 WARNINGDECAL Warning decal 1 MIRRORHANGER Rear view mirror hanger 1. Important customer information: Tuff Country EZ-Ride Suspension highly recommends that a qualified and/or certified mechanic performs this installation. If you desire to return your vehicle to stock, it is the customers responsibility to save all stock hardware. This vehicles reaction and handling characteristics may differ from standard cars and/or trucks. Modifications to improve and/or enhance off road performance may raise the intended center of gravity. Extreme caution must be utilized when encountering driving conditions which may cause vehicle imbalance or loss of control. DRIVE SAFELY! Avoid abrupt maneuvers, such as sudden sharp turns which could cause a roll over, resulting in serious injury or death.… Read More
Download 1998 – 2001 Ford Explorer 4WD Ford Ranger Explorer Sport Trac / Edge Mountaineer 4WD Torsion bar key front leveling kit
Filed Under (Ford) by Doe Namblas on 09-12-2013
Download Ford Timing Set Installation Instructions Thank you for choosing COMP Cams® products! We know you have options in valve train component selection and we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and also take a moment to review the included limited warranty information. Engine Application High Energy Magnum Hi-Tech Ford V6, 144-200 3223 Ford V6, 171 (2600-2800cc) 3236 Ford V8, 255, 289, 302 & Boss 302, 1965-1988 2120 3120 Ford V8, 289-351W & Boss 302, pre 1972 3220 Ford V8, 302-351W, 1972 & up 3230 Ford V8, 352-428, 1964-1974 3208 2108 3108 Ford V8, 351C, 351M, 400M, 1970-1982 3221 2121 3121 Ford V8, 429-460, 1968-1971 3222 2122 3122 Ford V8, 429-460, 1972-1987 2130 3130 Ford V8, 429-460 w/nine keyway crank gear 2134* Ford V8, 351W, 351W H.O., 1969-¹84 2135 3135 Ford V8, 5.0L 302 H.O., 1980-March 21, 1984 2131 3131 Ford V8, 5.0L 302, 351W, March 22, 1984-1992 2138 3138 Notes: * #2120 or #3120 should not be installed on 351W engines as they are designed for 255, 289, 302 or Boss 302 engines.… Read More
Download COMP Cams® Ford Timing Set Installation Instructions
Filed Under (Ford) by Doe Namblas on 17-03-2013
DownloadPARTS IN KIT: ITEM # QTY DESCRIPTION SERVICE PART # REPLACEMENT SOURCE 1 2 Spring, rear 2M5Z-5B669-AA Ford Dealer 2 2 Shock, rear 2M5Z-18125-BA Ford Dealer 3 1 Anti-roll bar, rear 1S4Z-5A772-BA Ford Dealer 4 1 Strut, RF 2M5Z-18124-BA Ford Dealer 5 1 Strut, LF 2M5Z-18124-BB Ford Dealer 6 2 Bump stop 2M5Z-3020-AA Ford Dealer 7 2 Spring, front 2M5Z-5310-AA Ford Dealer 8 2 Nut, upper strut piston W700212-S3091 Ford Dealer. TORQUE SPECIFICATIONS: FASTENER TORQUE (ft./lbs.) (EXCEPT WHERE NOTED) Rear shock upper mount nut 13 Rear shock lower mount nut 85 Rear lower control arm to knuckle 85 Rear anti-roll bar to control arm bolts 11 Rear anti-roll bar bushing clamp bolts 35 Upper strut piston nut 35 Strut tower nuts 18 Knuckle to strut bolt 66 Front anti-roll bar link to strut bolt 94 Caliper to Knuckle 21 Wheel nuts 37. REAR SUSPENSION INSTALLATION INSTRUCTIONS: STEP 1: Raise vehicle off ground and support with jack stands.… Read More
Download 2000-2004 Ford Focus ZX3 SVT Suspension Kit INSTALLATION INSTRUCTIONS
Filed Under (Ford) by Doe Namblas on 28-01-2014
Engine Application Ford V6, 144-200; Ford V6, 171 (2600-2800cc); Ford V8, 255, 289, 302 & Boss 302, 1965-1988; Ford V8, 289-351W & Boss 302, pre 1972; Ford V8, 302-351W, 1972 & up; Ford V8, 352-428, 1964-1974; Ford V8, 351C, 351M, 400M, 1970-1982; Ford V8, 429-460, 1968-1971; Ford V8, 429-460, 1972-1987; Ford V8, 429-460 w/nine keyway crank gear; Ford V8, 351W, 351W H.O., 1969-¹84; Ford V8, 5.0L 302 H.O., 1980-March 21, 1984; Ford V8, 5.0L 302, 351W, March 22, 1984-1992.
Tools and supplies needed: 1. Basic hand tools as required for your particular camshaft and balancer bolts 2. Torque wrench 3. Pro Cam Lube (part #153 or #154) or suitable replacement 4. Camshaft Degree Kit (part #4796 including degree video) 5. Crankshaft Socket (part #4798 for Ford 302-351W, 429-460) 6. Thread locking compound 7. Engine repair manual for your particular engine.
The following instructions begin after the timing cover and old timing set have been removed.… Read More
Download Ford COMP Cams Timing Set Installation Instructions
Filed Under (Other Manuals) by Doe Namblas on 31-03-2014
Download Applies To: All ModelsWith L4 or V6 Engine and A/TWith 44 mm I.D. Torque Converter Oil Seal Torque Converter Oil Seal Installation Tool The service manual procedure for installing the torque converter oil seal requires you to disassemble the transmission. Anew required special tool, which attaches to your existing 40 mm I.D. driver, lets you install this seal without removing the main shaft or disassembling the transmission. REQUIRED SPECIAL TOOLS Seal DriverAttachment: T/N 07XAD-001000A (Shippedtoall dealers March 2000 as a required special tool) 40 mmI.D. Driver: T/N 07746-0030100 ORDERING INFORMATION Additional seal driver attachments are available from American Honda using normal parts ordering procedures. WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. PROCEDURE 1. Remove the transmission (see section 14 of the appropriate service manual). 2. Remove and discard the torque converter oil seal. Be careful not to damage the torque converter housing. 3. Select the appropriate replacement seal.… Read More
Download Torque Converter Oil Seal Installation Tool
Filed Under (Ford) by Doe Namblas on 18-01-2014
Download Direct-Hit 2000 Ford Windstar 3.8L Test Details Hotline Archive # 124501 Confirmed Fix Vehicle Application: 1999 Ford Windstar 3.8L, Vin 4 2003 Ford Windstar 3.8L 2000 Ford Windstar 3.8L, Vin 4 Customer Concern: The battery light is on, but the alternator is charging. Has a code P1246. Tests/Procedures: 1. Disconnect the alternator and the Powertrain Control Module (PCM). Check the Violet (VT) (GENerator MONitor or GENMON) wire from the alternator to pin 20 of the PCM connector and the Red/Pink (RD/PK) (GENerator COMmand or GENCOM) wire from the alternator to pin 45 of the PCM for high resistance, an open, or a short to ground. Repair the wiring as needed. 2. If the wiring checks OK, reconnect the PCM and alternator. Start the engine and monitor the VT wire for a roughly 0-10v square wave signal. The signal will be around 40-50% normally with no loads on the system and minimal charging system output.… Read More
Download 1999-2000 Ford Windstar The battery light is on, but the alternator is charging Has a code P1246
Filed Under (Ford) by Doe Namblas on 01-01-2014
Download KIT CONSISTS OF: No. Qty Part No. Description 1. 1 713014-L DRIVER’S SIDE MOUNT 2. 1 713014-R PASSENGER SIDE MOUNT 3. 2 725002 1/2″-13 LOCK WASHERS 4. 2 725003 1/2″-13 FLAT WASHERS 5. 2 725004 1/2″-13 HEX NUTS 6. 1 FMC001 FORD INSTRUCTION MANUAL. INSTALLATION INSTRUCTIONS: Due to the extreme torque values of the 460 & 429 Ford V8 engines, it will be mandatory that you install a limit strap or straps to the driver’s side and passenger side engine mount. This limiting strap will prevent the engine from torquing beyond the limits of the rubber vulcanization. The straps should be installed with approximately 1/2″ tension reserve. This will permit the engine to torque up to 1/2″ in the motor mount area without causing any problem to the motor mount itself. Warranty on engine mount separation will be void if the limiting straps are not in place. The replacement of the small Ford V8 and straight 6 cylinder engines have become quite popular in Ford trucks.… Read More
Download FORD 429-460 BIG BLOCK ENGINE V8 ENGINE MOUNTS INSTALLATION INSTRUCTIONS