timing marks on nissan engine b14

You search Auto repair manual PDF about timing marks on nissan engine b14, search results will appear below. If search results do not exist, please search by others keyword.

1995 Nissan-Datsun 200SX Engine-Timing Chain/Front Cover Revised Procedure

Filed Under (Nissan) by admin on 15-02-2014

Download 1991-94 Sentra (B13) w/GA16DE 1991-93 NX1600 (B13) 1995-99 Sentra (B14) w/GA16DE 1995-98 200SX (B14) w/GA16DE SERVICE INFORMATION A revised service procedure for the engine front cover/timing chain has been adopted for the GA16DE. It is no longer recommended to remove the cylinder head when removing the timing chain/front cover(s). Utilize the following steps when servicing the front cover, timing chain, guides or tensioner(s) PARTS INFORMATION CLAIMS INFORMATION Please reference the “Revision C” pages of the Nissan “1992-1999 Warranty Flat Rate Information Manual”, Section “AG”, Op Codes AG12AA, AG14AA, AG142A, AG143A, AG144A and AG24AA. Also reference Section “CA”, Op Codes CA20AA and CA22AA. You will note that the descriptions and flat rate times applicable to the B13 and B14 vehicles (with GA16DE engines) for these Op Codes have been revised to reflect this new procedure. Caution ^After removing the timing chain, do not turn the crankshaft and camshaft separately or the valves will strike the piston heads.… Read More

2000 Plymouth Breeze TIMING BELT Removal Inspection Installation

Filed Under (Plymouth) by admin on 10-02-2014

Download 1. Raise vehicle on hoist and remove right front wheel. Remove right inner splash panel. Remove accessory drive belts. Remove crankshaft vibration damper. 2. Remove generator drive belt idler pulley. Remove lower timing belt cover. 3. Remove right engine support assembly vertical bolts from bottom of frame rail (timing belt end of engine). 4. Lower vehicle. Remove upper timing belt cover. Place floor jack under vehicle to support weight of engine and transaxle assembly. Remove 3 bolts attaching engine mount assembly to engine bracket. 5. Move A/C drier aside. Remove coolant reservoir tank. Remove right engine mount. Remove 3 bolts attaching engine mount bracket to engine block. 6. Rotate crankshaft clockwise to align timing marks on camshafts and oil pump housing. See Fig. 1 . 7. On models equipped with hydraulic tensioner, remove hydraulic tensioner bolts and remove tensioner. Place hydraulic tensioner in vise, and SLOWLY compress tensioner plunger. Align the holes in the tensioner body and plunger, and insert a pin through the body and plunger to lock the plunger in place.… Read More

2001 Daewoo Leganza SE TIMING BELT REMOVAL and INSTALLATION

Filed Under (Daewoo) by admin on 01-01-2014

Download 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt. 3. Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle. 4. Support engine assembly from above with Support Fixture (J-28467-B). See Fig. 1 . Remove engine mount bracket from timing belt end of engine. See Fig. 2 . 5. Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. See Fig. 3 . Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).… Read More

1999 Ford Contour/Mystique Timing Belt Workshop Manual

Filed Under (Ford) by admin on 01-01-2014

Download 1. CAUTION: The maximum amount by which the engine management system will adjust the camshaft timing (VCT control unit) is limited to two degrees. As a result of this an extremely high degree of accuracy is required for any work which affects the valve timing. NOTE: The locations of engine mountings and engine support insulators are described looking from the transaxle to the engine. NOTE: Operation steps which only apply to certain model variants and therefore do not apply to all vehicles are clearly marked. Disconnect the battery ground cable. 2. Raise and support the vehicle. For additional information, refer to Section 100-02 . 3. Loosen the right-hand front wheel nuts. 4. Remove the right-hand front wheel. 5. Remove the engine underschield (if equipped). 6. Remove the right-hand front splash shield. 7. NOTE: Mark the accessory drive belt direction if the belt is to be reused. Remove the accessory drive belt.… Read More

Ford COMP Cams Timing Set Installation Instructions

Filed Under (Ford) by admin on 28-01-2014

Download
Engine Application Ford V6, 144-200; Ford V6, 171 (2600-2800cc); Ford V8, 255, 289, 302 & Boss 302, 1965-1988; Ford V8, 289-351W & Boss 302, pre 1972; Ford V8, 302-351W, 1972 & up; Ford V8, 352-428, 1964-1974; Ford V8, 351C, 351M, 400M, 1970-1982; Ford V8, 429-460, 1968-1971; Ford V8, 429-460, 1972-1987; Ford V8, 429-460 w/nine keyway crank gear; Ford V8, 351W, 351W H.O., 1969-¹84; Ford V8, 5.0L 302 H.O., 1980-March 21, 1984; Ford V8, 5.0L 302, 351W, March 22, 1984-1992.
Tools and supplies needed: 1. Basic hand tools as required for your particular camshaft and balancer bolts 2. Torque wrench 3. Pro Cam Lube (part #153 or #154) or suitable replacement 4. Camshaft Degree Kit (part #4796 including degree video) 5. Crankshaft Socket (part #4798 for Ford 302-351W, 429-460) 6. Thread locking compound 7. Engine repair manual for your particular engine.
The following instructions begin after the timing cover and old timing set have been removed.… Read More

1994 Toyota Camry DX TIMING BELT REMOVAL and INSTALLATION

Filed Under (Toyota) by admin on 01-01-2014

Download 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of way. On Camry, remove coolant reservoir tank if it interferes with timing belt removal. Remove engine control (torque) rod from front of engine. 3. On all models, remove accessory drive belts. Using floor jack, slightly raise engine to remove weight from right (timing belt side) engine mount at timing belt cover. 4. Remove right (timing belt side) engine mount and bracket from front of engine. Remove spark plugs. Remove No. 2 timing belt cover and gaskets. See Fig. 1 . 5. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No.… Read More

NISSAN MAXIMA / ALTIMA / QUEST; BUZZING / WHINING NOISE FROM TIMING CHAIN AREA

Filed Under (Nissan) by admin on 02-01-2014

Download 2004-2008 Maxima (A34) 2004-2006 Altima (L31) with VQ35 engine ONLY 2004-2009 Quest (V42) IF YOU CONFIRM: There is a high frequency buzzing / whining noise coming from the secondary timing chain system. • The noise should increase in frequency with engine speed (RPM). • If the noise does not increase with engine speed, the timing chain system may not be the cause. Refer to the appropriate section of the Electronic Service Manual (ESM) for further diagnosis. ACTION: 1. Replace both secondary timing chains and both secondary timing chain tensioner “shoes” with the ones from the PARTS INFORMATION section of this bulletin (on Page 2). 2. Change the engine oil and filter. 3. For repair procedure, refer to the SERVICE PROCEDURE section of this bulletin (starting on Page 3). SERVICE PROCEDURE Write down all radio station presets. Presets 1 2 3 4 5 6 A B C 2. Disconnect both battery cables, negative cable first.… Read More

1998 Chevrolet Blazer Engine Oil Cooler Hose/Pipe Replacement

Filed Under (Chevrolet (Chevy)) by admin on 12-03-2014

Download 1998 Chevrolet Blazer – 4WD | Blazer, Bravada, Jimmy, S10 Pickup,  Sonoma (VIN S/T) Service Manual | Engine | Engine Mechanical – 4.3L | Repair Instructions. Engine Oil Cooler Hose/Pipe Replacement (4WD) Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6.… Read More

2000 Cadillac Catera TIMING BELT REPLACEMENT

Filed Under (Cadillac) by admin on 28-11-2013

Download 2000 Cadillac Catera V6-3.0L VIN R Timing Belt: Service and Repair Timing Belt Replacement. Removal Procedure ^ Tools Required -J 42069 Timing Belt Alignment Kit -J 42098 Crank Hub Torx Socket Notice: Failure to follow the described timing belt inspection and maintenance may result in a broken timing belt and cause severe engine damage. 1.Inspect the cold start counter (also called a heavy duty register) with a scan tool. If there are any cold starts (below -28° C or -20° F) visually inspect the timing belt for cracks. It cracks are noted, do not reuse the belt. Replace the belt and clear the cold start counter. If the belt is okay, and is reused, do not clear the cold start counter. 2.Remove the intake air resonator. Refer to Intake Air Resonator Replacement in Powertrain Management. 3.Remove the intake plenum. Refer to Intake Plenum Replacement. 4.Remove the timing belt cover. Refer to Timing Belt Cover Replacement.… Read More

2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner

Filed Under (Mitsubishi) by admin on 29-11-2013

Download 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned.… Read More

You might also likeclose