Honda Civic D-series Racing Intake Manifold Manual Installation Instructions

Download
Part # 307-05-0260 Racing Intake Manifold For Models and Years • 1992-1995 Honda Civic DX/EX (D15B7/D16Z6) • 1996-2000 Honda Civic EX (D16Y8) • 88-91 Honda CRX Si / DX* (*These models will require additional parts)
Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve).
Removal 1. Allow car to cool to ambient temperature. DO NOT attempt to work on warm or hot vehicle. 2. Drain coolant. 3. Relieve fuel pressure by loosening banjo bolt on top of fuel filter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced.… Read More

Honda Civic Racing Intake Manifold Installation Instruction

Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More

2007 Honda Accord CR-V and Civic Remote Engine Starter FAQ

Download
Model Information Release date for Accord Remote Starter System: September 20, 2007 Release date for CR-V and Civic Remote Starter System: End of September 2007 Technical Questions Q: What does the Honda Remote Engine Starter System do? A: The Honda Remote Engine Starter is a two-way remote system that starts and stops your vehicle’s engine anywhere within a 200-foot range. It’s designed to warm up your vehicle in the winter and cool it down in the summer. Q: How much is the Honda Remote Engine Starter? A: Approximately $499.00 without installation for all applicable Honda models. Check with your Honda dealer for the installation cost. Q: Can I install it myself? A: AHM does not recommend that customers install the Honda Remote Engine Starter due to the complexity of its electrical components. Authorized Honda Technicians are professionally trained to safely install the Remote Engine Starter. Q: Can I have my neighborhood audio shop install the Honda Remote Engine Starter?… Read More

Honda GXV340/GXV390 Engine Owners Manual

Download
LPG CONNECTIONS This engine is certified to comply with U.S. EPA and California ARB emission regulations using the Impco Beam regulator specified in the installation instructions (see below). Honda used this regulator and other specific parts and adjustments to demonstrate compliance with the emission regulations. Adjustable fuel system parts must have U.S. EPA and California ARB approved tamper resistant features to limit the available adjustment after the fuel system is correctly installed. If an equipment manufacturer did not install your engine in a product you will need the installation instructions for the Honda certified system (see below). If you choose not to use the Honda fuel system you must use a system that has been certified by the fuel system manufacturer to be used on this Honda engine. Or if you use a fuel system that is not already certified you must have certification test data satisfactory to the U.S.… Read More

2002-2006 Acura RSX-S Throttle Body To Intake Manifold Adapter

Download Part #: KIM01 K20A/A2/A3/Z1 Throttle Body To RBC/RRB/RBB Intake Manifold Adapter This adapter provides the SOLUTION for directly bolting up a 02-06 RSX-S/ITR or 02-05 Civic Si/CTR Throttle Body to an Accord Euro R, 06-08 Civic Si, or 04-05 TSX Intake Manifold. Ease of fitment has been confirmed for the following vehicle/engine/mount combinations: -1992-199 5 Honda Civics equipped with a K20 engine and Hasport EGK1 engine mounts -1996-200 0 Honda Civics equipped with a K20/24 engine and Hasport EKK2 engine mounts -1994-200 1 Acura Integras equipped with a K20 engine and Hasport EGK1 engine mounts -2002-200 6 Acura RSX-S/Honda ITRs with a K20 engine and all available engine mounts. 1. PREPARATION 1. Remove the EVAP hose, brake booster hose, PCV hose, vacuum hose, water bypass hoses, throttle cable, fuel lines, fuel injector connectors, IAC valve connector, TP sensor connector, MAP sensor connector, and EVAP canister purge valve connector from your current intake manifold and throttle body setup.… Read More

1995-1996 Honda Civic V 1.4L L4 Part 57-0527 Installation Manual

Download
Honda Civic V 1.4L L4 1995-1996, Honda Civic V 1.4L L4 D14A4 Eng 1997-2001, Honda Civic V 1.6L L4 105BHP 1995-2001 (15.09.10)
1. Unclip and remove air box lid from the vehicle. (Fig. 1) 2. Unbolt & remove the resonator box from the vehicle. (Fig. 2) 3. Disconnect the cam cover breather from the air box base. (Fig. 3) 4. Remove the air temp sensor from the side of the air box. (Fig. 4) 5. Loosen the clip on the throttle neck, unbolt and remove the air box base. (Fig. 5) 6. Remove the 2 short breather hoses from the cam cover outlet and the metal breather hose. (Fig. 6&7) 7. Fit the stepped rubber adaptor onto the throttle housing and firmly tighten using the #44 hose clamp supplied. (Fig. 8) (Note: – This adaptor should be a tight fit) 8. Fit the plastic intake tube into the stepped rubber adaptor & firmly tighten using the #60 hose clamp supplied.… Read More

2001-2005 Honda Civic EX Air Intake Manual Installation Instructions

Download
Bomz Racing 01-05 Honda Civic EX Air Intake Installation Guide Removal of Factory Intake 1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. 2. Disconnect the air temperature sensor electrical connection. 3. Unclip the battery cable from the air inlet duct. 4. Loosen and remove the two bolts that secure the air inlet duct. 5. Remove the air inlet duct. 6. Loosen and remove the four bolts that secure the air intake resonator. 7. Loosen and remove the two bolts that secure the throttle body plenum. 8. Loosen hose clamp that secures the plenum to the throttle body. 9. Using a pair of piers, depress and pull back the hose clamp on the crank case vent at the cam cover. 10. Pull firmly upwards to remove the throttle body plenum. 11. Using a flat blade screwdriver, unclip the wire harness from the resonator. 12. Unclip the throttle cable and cruise control cable, then remove the resonator by pulling upwards.… Read More

1996-2000 Honda Civic Rear Main Oil Seal Leaks

Download 1996-00 Civic – ALL 2001 Civic – See VEHICLES AFFECTED Civic Rear Main Oil Seal Leaks (Supersedes 01-040, 1996 – 2001 Civic Rear Main Seal Leak , dated June 12, 2001) SYMPTOM The engine leaks oil between the block and the transmission. PROBABLE CAUSE The rear main oil seal (crankshaft oil seal) is contaminated. REPAIR PROCEDURE 1. Remove the transmission. Refer to section 13 or 14 of the appropriate service manual. 2. Remove and discard the rear main oil seal (crankshaft oil seal). 3. Install the new oil seal. Refer to page 7 – 29 of the ’96-00 service manual or page 7-27 of the ’01 service manual. 4. Reinstall the transmission. 5. Reinstall the drain plug with a new sealing washer. 6. Refill the transmission with the appropriate fluid. 7. 2001 models only. Do the idle learn procedure: Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off, then start the engine.… Read More

1988-2000 Honda Civic Clunk or Squeak From Rear Suspension

Download 1988-2000 Honda Civic – ALL 1997-2001 Honda CR-V – ALL 1993-2097 Honda Del Sol – ALL Clunk or Squeak From Rear Suspension SYMPTOM A clunk or squeak from the rear suspension when going over rough or bumpy roads. PROBABLE CAUSE Broken rear trailing arm bushing(s). CORRECTIVE ACTION Replace the rear trailing arm bushing(s). REPAIR PROCEDURE NOTE: ISIS online service manual information is only available for vehicles 1990 and newer. 1. Remove the rear trailing arm: •Refer to the suspension section of the appropriate service manual, or •Online, enter keyword REAR SUSPENSION, then select Suspension Arms Replacement from the list. 2. Mark the trailing arm at the arrow on the bottom of the bushing. 3. Place the arm on a hydraulic press, supported by the hub base, with the spindle facing up. 4. With the hub driver, press the old bushing out of the trailing arm. 5. Install the new bushing with the short end toward the outside of the vehicle.… Read More

AEM V2 Air Intake System Manual Installation Instructions

Download
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6001
1992-1995 HONDA Civic SI L4-1.6L C.A.R.B.E.O. #D-670
1992-1995 HONDA Civic LX L4-1.5L Manual Trans. C.A.R.B.E.O. #D-670
1994-1995 HONDA Civic EX L4-1.6L Manual Trans. C.A.R.B.E.O. #D-670
1992-1995 HONDA Civic DX Hatchback L4-1.5L Manual Trans. C.A.R.B.E.O. #D-670
1992-1995 HONDA Civic DX L4-1.5L Manual Trans. C.A.R.B.E.O. #D-670
1992-1993 HONDA Civic L4-1.6L Manual Trans. C.A.R.B.E.O. #D-670
1. Preparing Vehicle a. Make sure vehicle is parked on level surface. b. Set parking brake. c. If engine has run in the past two hours, let it cool down. d. Disconnect all negative battery terminals. e. Raise the front of the vehicle with a jack. Refer to your owner’s manual for proper jack and jack stand placement to properly support vehicle. Support your vehicle using properly rated jack stands before wheel removal or while working under the vehicle. NEVER WORK UNDER A VEHICLE WITHOUT USING JACK STANDS.… Read More