starting tips for a 2002 buick in cold weather

You search Auto repair manual PDF about starting tips for a 2002 buick in cold weather, search results will appear below. If search results do not exist, please search by others keyword.

1997 Buick Century COLD ENGINE TICK OR RATTLE AFTER START-UP

Filed Under (Buick) by admin on 05-04-2014

Download 1997 Buick Century Limited 3.1/3.4L ENG TICK OR RATTLE AFTER COLD START UP COLD ENGINE TICK OR RATTLE AFTER START-UP (REPLACE PISTON/PIN ASSEMBLY) Model(s): 1994-95 Buick Regal 1994-97 Buick Skylark 1994-98 Buick Century 1994-95 Chevrolet Beretta Corsica, Lumina, Monte Carlo 1996-98 Chevrolet Venture 1997-98 Chevrolet Malibu 1993-97 Oldsmobile Cutlass Supreme 1994-96 Oldsmobile Cutlass Ciera 1994-97 Oldsmobile Achieva 1996-98 Oldsmobile Silhouette 1997-98 Oldsmobile Cutlass 1994-98 Pontiac Grand Am, Grand Prix 1996-98 Pontiac Trans Sport with 3100, 3400 V6 Engine (VINs M, E – RPOs L82, LA1) CONDITION Some customers may comment on a ticking type noise that begins shortly after cold engine start-up and gradually diminishes as the engine warms up. In most cases, the noise is gone after five (5) minutes. In severe cases, the noise may not disappear when lhe engine is hot. CAUSE Under normal design tolerances when the piston pin bore is produced at the maximum tolerance and the piston pin is produced at the minimum tolerance (min-max tolerance) trace noise levels can occur.… Read More

2002-2004 Nissan Altima W/QR25 ENGINE; NO-START AFTER ‘COLD SOAK’

Filed Under (Nissan) by admin on 29-01-2014

Download Altima; vehicles built up to 1N4AL11D(*)4C181189 Sentra; ALL APPLIED DATES: Altima; vehicles built up to 12-17-2003 Sentra; ALL IF YOU CONFIRM • After a ‘cold soak’,* the engine cranks (turns with starter), but does not start. *Cold soak: Engine has cooled down to ambient (outside) temperature, regardless of summer or winter seasonal variations. • The engine may start if it is cranked for an extended period (more than 5 seconds) or if the throttle is opened during cranking. • After starting and operating for a few minutes the engine runs normally. ACTIONS • Replace the starter motor. • Add 1 can of Nissan Fuel System Cleaner into the fuel tank. • Perform ECM Part Number Check to see if the vehicle you are working on needs ECM Reprogramming. • Perform ECM Reprogramming, if needed. IMPORTANT: The purpose of “ACTIONS” (above) is to give you a quick idea of the work you will be performing.… Read More

2000-2002 Audi TT Part RD3025p Cold Air Intake System

Filed Under (Audi) by admin on 31-12-2013

Download Note: Disconnect the negative battery terminal before starting this installation. 1. Remove the air intake box and air intake duct that leads to the mass air flow sensor. 2. Slip the 2 3/4″ straight hose over the mass air flow sensor use two clamps and tighten the clamp on the mass air flow sensor. (See fig. 2) 3. Take the vibra-mount and screw it into the bracket located on the side of the strut tower mount. (See fig. 3) Removing the head lamp and the front bumper. 4. Remove the 3 m6 bolts located on the extended plastic arms on the head lamp. (See fig. 4) You will also disconnect the three harness clips located on the back side of the head lamp. (See fig. 5) 5. In order to remove the bumper you need to peel back the splash guards in the wheel well. Unscrew two m6 nuts on each side of the frame located behind the splash guards.… Read More

PERFORMER RPM BUICK CYLINDER HEADS For 1967-1981 400-455 Buick V8 Engines Catalog #60039 #60049 INSTALLATION INSTRUCTIONS

Filed Under (Buick) by admin on 09-01-2014

Download Installation is the same as for original equipment cylinder heads. Consult service manual for specific procedures, if necessary. Be sure that the surface of the block and the surface of the head are thoroughly cleaned to remove any oily film before installation. Use alcohol or lacquer thinner on a lint-free rag to clean. Apply oil or suitable thread lubricant to head bolt threads and the underside of bolt heads and washers to prevent galling and improper torque readings. Use thread sealant on any bolts that go into coolant passages. Torque top row of bolts to 110 ft./lbs. and bottom row of bolts to 100 ft./lbs. in three or four steps, following the factory tightening sequence (See Figure 1) . A re-torque is recommended after the initial star-up and cool-down (allow 2-3 hours for adequate cooling). Other Assembly Tips: When installing the sparkplugs and exhaust manifolds, be sure to use a high temperature anti-seize compound on the threads to reduce the possibility of thread damage in the future.… Read More

Information on Error Codes on Radio Display – Their Cause and Corrective Action

Filed Under (Other Manuals) by admin on 25-12-2013

Download odels: 1995-1996 Buick Roadmaster 1995-1999 Buick LeSabre 1995-2004 Buick Century, Regal 1995-2005 Buick Park Avenue 1996-1999 Buick Riviera, Skylark 2004-2005 Buick Rainier 1995-1999 Chevrolet Lumina, Monte Carlo, Fullsize Pickup Models (Old Style) 1995-2005 Chevrolet Blazer 1996 Chevrolet Lumina APV 1996-1999 Chevrolet Cavalier 1996-2000 Chevrolet Express Van 1996-2002 Chevrolet Astro Van 1997-2002 Chevrolet Camaro 1997-2003 Chevrolet Malibu 1997-2005 Chevrolet Corvette, Venture 2000-2005 Chevrolet Silverado 2002-2005 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2005 Chevrolet SSR 2004-2005 Chevrolet Classic, Colorado 1995-1999 GMC Fullsize Pickup Models (Old Style) 1995-2002 GMC Jimmy 1996-2000 GMC Savana Van 1996-2002 GMC Safari Van 2000-2005 GMC Sierra 2002-2005 GMC Envoy, Envoy XL 2004-2005 GMC Canyon, Envoy XUV 1995-1999 Oldsmobile Aurora, Eighty Eight 1995-1997 Oldsmobile Cutlass Supreme 1999-2004 Oldsmobile Alero 1998-2002 Oldsmobile Intrigue 1995-1996 Oldsmobile Ninety Eight 1996-1999 Oldsmobile Achieva 1996-2004 Oldsmobile Bravada, Silhouette 1995-1999 Pontiac Bonneville, Sunfire 1995-2002 Pontiac Firebird 1995-2005 Pontiac Grand Prix 1996-1997 Pontiac Trans Sport 1996-2000 Pontiac Grand Am 1997-2005 Pontiac Montana 2003-2005 HUMMER H2.… Read More

2002-2004 Ford Focus SVT COLD AIR SYSTEM

Filed Under (Ford) by admin on 26-02-2014

Download Part Number 21-451. Read and understand these instructions BEFORE attempting to install this product. 1) Getting Started a) Make sure vehicle is parked on a level surface. b) Set parking brake. c) Jack the front of the vehicle and support using properly rated jack stands d) If engine has run with in the past two hours let it cool down. 2) Removal of the stock intake system. a) Stock system installed on vehicle. b) Remove the wiring harness from the MAF Sensor. c) Remove the clamp securing the primary intake pipe to the throttle body. d) Disconnect the breather hose from the vehicle. e) Remove the stock intake system from the vehicle. f) Upper Stock system removed from vehicle. g) Remove the MAF sensor from the stock intake system. h) Remove the 90 degree plastic fitting from the stock system. i) Remove the battery cover from the vehicle. j) Disconnect the battery.… Read More

2002-2003 Acura RSX Icebox Cold Air Intake Installation Instructions

Filed Under (Acura) by admin on 11-01-2014

Download Honda Civic Si & Acura RSX Icebox Cold Air Intake Installation Instructions (2002-2003 Honda Civic Si) (2002-2003 Acura RSX—All) Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan. •Remove ground strap bracket on side of transmission (C). Relocate ground strap from transmission bracket to top of transmission (D). Step #2 Install Comptech Airbox •Install (3) stock rubber grommets* (E) through large holes on underside of mounting ears on Icebox (a small dab of filter oil may be used to ease this process).… Read More

Buick Regal Cold Air Induction System Installation Manual

Filed Under (Buick) by admin on 17-02-2014

Download Thrasher Engineered Performance – Cold Air Induction Kit for 97 and newer Pontiac Grand Prix, Buick Regal and Chevrolet Monte Carlo. Follow steps 1-16 below for 97-98 model year vehicles. The procedure for 99-newer model year vehicles is currently under development. Step 1 (97-98) Remove the (3) 13mm bolts holding the fender – radiator support brace. This step is not pictured. Step 2 (97-98) Loosen the wing nut on the large clamp securing the ribbed duct, and remove the duct from the plastic air box outlet as shown. Step 3 (97-98) Remove the IAT (Intake Air Temp) sensor from the rubber duct. Save for reinstallation on your replacement duct. Step 4 (97-98) Pull the duct from the throttle body. This requires a lot of force, pull hard. When removed, the duct will be as pictured. Step 5 (97-98) Release the air box clamps and remove the cover, plastic outlet and filter element.… Read More

2000 Volkswagen Beetle Vehicle starts and stalls

Filed Under (Volkswagen (VW)) by admin on 01-01-2014

Download Vehicle Application: 2000 Volkswagen Beetle 2.0L, GAS, Eng Des AEG 2002 Volkswagen Beetle 2.0L, GAS, Eng Des AZG 2000 Volkswagen Jetta GL 2.0L 2002 Volkswagen Eurovan 2.8L 2000 Volkswagen Jetta GLS 2.0L, Eng Cfg L4, Eng Des AEG 2002 Volkswagen Jetta GL 2.0L, Eng Des AVH 2000 Volkswagen Jetta GLS 2.8L, Eng Cfg V6, Eng Des AFP 2002 Volkswagen Jetta GLS 2.0L, Eng Cfg L4, Eng Des AVH 2001 Volkswagen Beetle 2.0L, GAS, Eng Des AVH 2002 Volkswagen Jetta GLS Wagon 1.8L 2001 Volkswagen Jetta GL 2.0L, Eng Des AEG 2003 Volkswagen Jetta GLS 2.0L, Eng Cfg L4, Eng Des AVH, USA/Canada 2001 Volkswagen Jetta GLX 2.8L 2007 Volkswagen Passat 3.6 3.6L 2002 Volkswagen Beetle 1.9L, DIESEL, Turbo, Eng Des ALH Customer Concern: Vehicle starts and stalls. Trouble code P1570 (17978). The security light is flashing. Tests/Procedures: 1. As of model year 2000, Volkswagen has changed the immobilizer system and the 7 digit PIN numbers are no longer available to the aftermarket.… Read More

2002 Buick Truck Rendezvous Trim Panel Replacement

Filed Under (Buick) by admin on 13-12-2013

Download Tools Required J 38778 Door Trim Pad and Garnish Clip Remover Removal Procedure 1. Open the door. 2. Disconnect the power window switch assembly. 3. Remove the screws from the front door trim panel 4. Use the J 38778 to remove the trim panel. 1. Reposition the electrical harness connectors. 2. Remove the trim panel from the vehicle. Installation Procedure Important: Before installing the front door trim panel , discard the old trim panel retainers and replace with NEW trim panel retainers. 1. Install the new retainers to the front door trim panel . 2. Route the electrical connectors through the trim panel . 3. Align the trim panel to the door inner panel, guiding the door handle through the trim panel. 4. Install the upper edge of the trim panel to the top edge of the inner door panel, pressing down firmly until the trim panel is fully seated.… Read More

You might also likeclose