silverado transmission stuck in gear

You search Auto repair manual PDF about silverado transmission stuck in gear, search results will appear below. If search results do not exist, please search by others keyword.

2001 Chevrolet Chevy K Silverado Transmission Stuck in Second or Third Gear

Filed Under (Chevrolet (Chevy)) by admin on 19-12-2013

Download Malfunction Indicator Lamp (MIL) On, Transmission Stuck in Second or Third Gear, Instrument Cluster Inoperative (Verify and Repair Source of Voltage Loss In Transmission Solenoid Power Supply Circuit ) Models: 2006 and Prior GM Passenger Cars and Light Duty Trucks 2005-2006 HUMMER H2 2006 HUMMER H3 2005-2006 Saab 9-7X with 4L60-E, 4L65-E, 4L80-E or 4L85-E Automatic Transmission (RPOs M30, M32, M33, MT1, MN8) Condition Some customers may comment on one or more of the following conditions: Upon investigation, one or all of the diagnostic trouble codes (DTCs) P0740, P0753, P0758, P0785, P0787, P0973, P0976, P1860, P2761, P2764 and P2769 may be set depending on the vehicle. Cause The most likely cause of this condition may be a loss of voltage to the transmission solenoid power supply circuit. This condition may also be the result of an incorrect installation of an aftermarket electronic device such as a remote starter or alarm system.… Read More

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Filed Under (Other Manuals) by admin on 01-01-2014

Download Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) #05-07-30-031: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) – (Nov 11, 2005) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case.… Read More

2002 Dodge Truck RAM 2500 Truck AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING

Filed Under (Dodge) by admin on 01-01-2014

Download 2002 Dodge Truck RAM 2500 Truck 4WD L6-5.9L DSL Turbo VIN 6 Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Testing and Inspection Symptom Related Diagnostic Procedures. 46RE AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING Before road testing, be sure the fluid level and control cable adjustments have been checked and adjusted if necessary. Verify that diagnostic trouble codes have been resolved.Observe engine performance during the road test. A poorly tuned engine will not allow accurate analysis of transmission operation. Operate the transmission in all gear ranges. Check for shift variations and engine flare, which indicates slippage. Note if shifts are harsh, spongy, delayed, early, or if part throttle downshifts are sensitive. Slippage indicated by engine flare, usually means clutch , band or overrunning clutch problems. If the condition is advanced, an overhaul will be necessary to restore normal operation. A slipping clutch or band can often be determined by comparing which internal units are applied in the various gear ranges.… Read More

429-460 Ford V8 ACCU-DRIVE CAM GEAR DRIVE SYSTEM INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 22-12-2013

Download POWER PACKAGE: Edelbrock Accu-Drive gear drives are part of a Total Power Package parts system that can be completed with the use of dyno- matched Performer , Performer RPM, or Torker II cams, intake manifolds, and carburetors. For competition applications, use Edelbrock Victor intake manifolds. Please refer to the Power Package Guide in the Edelbrock catalog to select all the components you need.  ACCU-DRIVE OPERATING PRINCIPAL The Accu-Drive system utilizes a free floating idler gear that is self-aligning and connects the crankshaft and camshaft gears into proper mesh. The large floating idler gear is positioned on the right side of the engine (passenger side). During normal operation, the drive power is transmitted from the crankshaft through the large floating idler to the camshaft gear. During the running operation, there is no backlash between these gears. The small idler gear (located opposite the large idler gear) is also free floating.… Read More

Ford BD Performance Transmission Installation Instructions

Filed Under (Ford) by admin on 14-01-2014

Download
REMOVAL: 1) Disconnect the negative battery cable(s). 2) Place the transmission into the Neutral (N) position. 3) Raise the vehicle on a hoist. 4) Mark the drive shaft and pinion yokes for assembly alignment. On 4WD models, remove the skid plate. 5) Remove the transmission oil filter tube nut and filler tube. 6) Position a drain pan & disconnect the transmission fluid cooler tubes at the cooler bypass valve. 7) Remove the drive shaft. On 4WD models, remove the front drive shaft & transfer case assembly. On SuperDuty/Motorhome models, remove the transmission mounted parking brake assembly. 8) NOTE: If the vehicle is equipped with a PTO (Power Take-Off) unit, all or part of the PTO will need to be removed. 9) Disconnect the shift cable from the transmission and manual lever. 10) Disconnect the cable housing from the bracket. 11) Disconnect the digital transmission range (TR) sensor connector. 12) Remove the transmission heat shield.… Read More

Checking oil level in automatic transmission and adding oil

Filed Under (Other Manuals) by admin on 28-03-2014

Download TRANSMISSION 722.700 in MODEL 168.031 /032 /033 /131 /132 /133 TRANSMISSION 722.701 in MODEL 168.006 /007 /008 /009 /109 TRANSMISSION 722.702 in MODEL 168.035 /135 TRANSMISSION 722.750 /751 in MODEL 414.700. Adding transmission oil Risk of accident. Secure vehicle to prevent it from moving. AS00.00-Z-0005-01A Danger! Accidents may result if the vehicle starts off unintentionally with the Wear closed and snug-fitting work clothes. engine running. Risk of injury. Do not grasp hot or rotating parts. Crushing and burn injuries may result while working on engine during when it is being started or when it is in operation. 1 Remove locking pin (1) To do this, break off the plate on the locking pin using a suitable tool and press out the remaining pin in the cap downwards 2 Remove cap (2) 3 Fill with transmission oil The vehicle must be horizontal. Transmission oil (ATF) in accordance with BB00.40-P-0236-10A Specifications for Operating Fluids, sheet no.… Read More

MONSTER TRANSMISSIONS : FORD TRANSMISSION INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 31-12-2013

Download
Please Note : The following instructions were made to act as a guide/reference, if you are inexperienced with performing an automatic transmission installation it is highly recommended that you contact a certified experienced professional to perform the installation and/or make the proper adjustments for you! Instructions : (1) Pre-installation instructions; Disconnect Battery terminal, inspect and check transmission coolant lines for damage, flush lines and coolant system thoroughly. (2) Inspect crank well for converter hub wear, and clean this area. (3) Check Flywheel for cracks and converter bolt holes for wear. (4) Inspect back of engine block where transmission mates, ensure block is clean, no wires or cables are in the way of installation. (5) Inspect and verify both dowel pins are clean and secure in block. (6) Ensure Block Plate is aligned and straight. (7) Clean area of block so transmission can make a good ground. “Warning” Transmission will suffer permanent damage if grounded improperly!… Read More

2002 Jaguar X-Type Transmission Fluid Level Check

Filed Under (Jaguar) by admin on 29-12-2013

Download 2002 Jaguar X-Type V6-2.5L Vehicle Level Maintenance Fluids Fluid – A/T Testing and Inspection. Transmission Fluid Level Check Raise and support the vehicle. 1. Connect the approved Jaguar diagnostic system. 2. Make sure J-Gate shift selector is in the Park position (P). 3. With the engine running and the foot brake applied, move the J-Gate shift selector through “P-R-N-D-4-3-2″ and back to the “P” position to circulate the automatic transmission fluid until the temperature reaches 30 to 40°C (86 to 104°F) on the approved Jaguar diagnostic system. 4. When the automatic transmission fluid temperature reaches 35°C (95°F) check that the selector lever is in the “P. position raise the vehicle. Motor / ALLDATA Online – 2002 Jaguar X-Type V6-2.5L – Testing and… http://www.motoralldata.com/alldata/MOTOR~V71595976~C40438~… 2 of 4 3/28/2008 11:44 AM Zoom Sized for Print If the automatic transmission fluid does not come out of the transmission fluid level tube the automatic transmission fluid level is insufficient.… Read More

FORD TRANSMISSION INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 15-03-2014

Download (1) Pre-installation instructions; Disconnect Battery terminal, inspect and check transmission coolant lines for damage, flush lines and coolant system thoroughly. (2) Inspect crank well for converter hub wear, and clean this area. (3) Check Flywheel for cracks and converter bolt holes for wear. (4) Inspect back of engine block where transmission mates, ensure block is clean, no wires or cables are in the way of installation. (5) Inspect and verify both dowel pins are clean and secure in block. (6) Ensure Block Plate is aligned and straight. (7) Clean area of block so transmission can make a good ground. “Warning” Transmission will suffer permanent damage if grounded improperly! Installation : (1) Transmission Fluid: you need about 10 to 12 quarts of fluid for installation, Dextron III with Mercon, 1968 – 1993 Vehicles and Mercon 5, 1994 and Newer, any brand name. (2) If transmission was purchased with a torque converter from Monster Transmission & Performance, no need to follow step (3).… Read More

Ford 8.8″ 31 spline OX Locker installation Instructions

Filed Under (Ford) by admin on 16-12-2013

Download Note: Depending on the year, make, and model of your vehicle, some deviations and modifications may be needed during installation: Routing of the cable (keep it kink free) Placement of the shifter Heat Shields and grommets for cable protection. Make certain cable action is free & smooth. Use High StrengthLoctitewhere specified and allow for proper cure times. Install the 4 springs in the 4 chamfered holes. 8 -bolts, º-28 thread 8 -spring washers 1 -small carrier cap 1 -thrust washer 1 -locking ring gear 1 -locking side gear 4 -springs 1 -big carrier cap (attached to carrier) Install thrust washer behind locking side gear. Carrier Assembly 1. 2. OX Locker needs final assembly. Remove all packaging including any tie wraps. Picture shows the parts that need to be assembled:1 -long shaft 1-spider gear 1 -snap ring 1 -dowel pin 1 -spider gear cap 1 -set screw 1 -spider gear washer.… Read More

You might also likeclose