shift linkage cable for 99 silverado

You search Auto repair manual PDF about shift linkage cable for 99 silverado, search results will appear below. If search results do not exist, please search by others keyword.

1982-2003 Ford Mustangs Double Hook Clutch Quadrant and Clutch Adjustment Kit INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 23-11-2013

Download DOUBLE HOOK QUADRANT INSTALLATION INSTRUCTIONS: STEP 1: At the bellhousing, remove the plastic splash shield. Use a pry-bar to slacken the clutch cable and disconnect it from the clutch fork. STEP 2: Under the dash, pull the end of the cable loose from the quadrant STEP 3: Under the dash there are two plastic parts that make up the factory clutch quadrant mechanism. They are held in place by clips on the end of the shafts. Remove the clips from the end of the shafts. STEP 4: Press the clutch pedal fully to the floor (you may have to pull the carpet aside) and pry the plastic quadrant and springs off. STEP 5: Press the clutch pedal to the floor again. Align the new aluminum quadrant with the shafts and slide the aluminum quadrant on. Center the quadrant in line with the hole where the cable comes through the firewall.… Read More

2002 Chrysler 300M Special GEAR SHIFT CABLE – FLOOR / REMOVAL

Filed Under (Chrysler) by admin on 10-12-2013

Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More

Ford C-4 Bracket and Lever Installation Instructions

Filed Under (Ford) by admin on 01-09-2012

Download STEP 1. Raise and safely support the vehicle at least 1-2 feet off the ground. Remove the nut and lock- washer holding the downshift linkage onto the downshift lever shaft. The downshift lever is the outer lever on C-4 transmissions. Pull the lever off the shaft and allow the linkage to hang free. Remove and discard stock shift linkage rods. Late C-4 transmissions have a Neutral safety/Backup light switch on the transmission shift lever. If your transmission is so equipped, remove the two bolts holding the switch in place and slide it off the shift shaft. Disconnect the switch at the factory plug and discard it. STEP 2. Install the B&M selector lever, See figure 1 . Note: The B&M lever must point downward for proper operation. If the stock shift lever on your transmission points down, you will have to remove the lower part of the stock arm by cutting it off to clear the B&M lever, (See figure 1 ) .… Read More

1996-1999 Audi A4/1998 VW Passat Short Shifter Installation Instructions

Filed Under (Audi) by admin on 18-02-2014

Download The following parts are included in this package: – Shifter – Shift Linkage Bracket The following tools are recommended for installation: – 13mm socket and ratchet – 10mm socket and ratchet – socket wobble (universal joint) attachment – socket extension – snap ring / circlip pliers – 6mm allen socket head bit – flexible plunger-type four-claw retriever – torx T-25 driver (only for 2000 A4, S4 and A6 Biturbo) Installation Tips Familiarizing yourself with the short shifter pieces will help make the installation process very easy. Take the time to study each of the pieces that make up the short shifter and read through the installation instructions before you begin. Step 1 – Remove shift knob Step 2 – Remove shift boot Pry up the edges of the shift boot with fingertips, remove from console. Step 3 – Remove black plastic collar Step 4 – Remove circlip Use circlip pliers to remove circlip from shift lever.… Read More

2002 Acura RSX-Type S Short Throw Shift Adapter Installation Manual

Filed Under (Acura) by admin on 09-12-2013

Download 1. Pull down chrome collar and carefully unscrew and remove the stock shift knob. 2. Remove the front console cover. Pull up from the front to unclip the clips and remove from the vehicle. 3. Remove the 2 screws securing the front part of the console. Remove any additional screws that may be holding the center part of the console in place, this may vary by year and model. Lift the 2 tabs shown to the right over the center section of the console so that they rest on the outside of the console assembly. 4. Spread the front sections of the console away from the center console to unclip the 2 clips securing them in place. This may be simplified by pushing from the inside with a hard object next to the clip. 5. Pull the center console to the rear of the vehicle ensuring the sides of the front section of the console remain apart and out of the way.… Read More

2001 Pontiac Grand Prix Shifter A/T: Service and Repair

Filed Under (Pontiac) by admin on 31-12-2013

Download 2001 Pontiac Grand Prix V6-3.8L VIN K. Shifter A/T: Service and Repair Shift Control Replacement Removal Procedure 1. Remove the horseshoe clip (1) from front of shift control knob, and remove knob. 2. Remove the Console Trim Plate. 3. Remove the console wiring harness. 4. Remove the console shift control wiring harness. 5. Remove the automatic transaxle range selector cable. 6. Remove the park/lock cable. 7. Remove the console shift control nuts. 8. Remove the console shift control. Installation Procedure 1. Install the console shift control. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the console shift control nuts. ^Tighten the console shift control nuts to 24 Nm (18 ft. lbs.) . 3. install the park/lock cable. 4. Install the automatic transaxle range selector cable. 5. Install the console shift control wiring harness. 6. Install the console wiring harness. 7. Install the Console Trim Plate. 8. Adjust the transaxle range selector cable.… Read More

Honda Goldwing GL1200 Electronic Cruise Control Manual Installation

Filed Under (Honda) by admin on 01-01-2014

Download
1st step. The actuator spool is installed in the CIU housing with the actuator cable. The actuator spool is rotated to fully extend the cable. 2nd step. The dual spool and carburettor cable are installed. The carburettor cable is attached to the lower groove in the dual spool. The other end of the carburettor cable is attached to the carburettors. Note the position of the roll pin. It is nearly contacting the end of the groove in the actuator spool. The free play in the carburettor cable must be adjusted so that the cable outer can be pulled out 2 ~ 3mm before the carburettors start to open. This ensures that the cruise control cannot prevent the carburettors returning to idle. If more free play is allowed the response of the cruise control is compromised. This adjustment of free play is usually performed after final assembly of the CIU is completed and the CIU is in its final location.… Read More

FORD TRUCK INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 24-11-2013

Download A. Before you start. 1. Read all warnings and instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part’s list). 2. If at anytime during the installation you encounter something different from what is outlined in the instructions, call technical support. (928) 636-0979 or go online to our webpage at http://www.perfor- manceaccessories.com. 3. Park the vehicle on a clean, dry, flat, level surface. Block the tires so the vehicle cannot roll in either direction. 4. Battery cable. a. Disconnect both battery cables. Be sure to disconnect the negative cable first, then the positive cable. B. Get ready to install the kit . 1. Steering column. a. Most steering columns have a slip joint. Check the joint to see if the inner and outer sections are pinned together. If they are pinned together, drill out pins. If there is no slip joint steering shaft will need to be replaced with an aftermarket shaft designed to accomodate the lift.The shaft will telescope out approximately 3/4″ for a 2″ lift and approximately 1 1/4″ for a 3″ lift.… Read More

General Motors Accessories Headrest DVD System Display Monitor Inoperative

Filed Under (Other Manuals) by admin on 21-12-2013

Download Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps.… Read More

1980-1992 Ford AOD Shift Improver Kit Installation Instructions

Filed Under (Ford) by admin on 01-01-2014

Download IMPORTANT: We recommend that you read through the instructions completely before beginning the installation so you can familiarize yourself with the installation procedure and tools required. Check the tool list at the end of these instructions for the tools required to install your B&M AOD Shift Improver Kit. Installation of the B&M AOD Shift Improver Kit can be accomplished by anyone with minimum mechanical experience. It is however, important to closely follow the instructions. Read each step carefully before proceeding, if you do not understand, go back and read the step again. NOTICE: The B&M AOD Shift Improver Kit is not a cure-all for an ailing transmission. If your transmission is slipping, chatters or is in poor general shape, the installation of this Shift Improver Kit may worsen the condition. However on a properly operating transmission in average condition, the B&M AOD Shift Improver Kit will provide the kind of transmission performance you are looking for.… Read More

You might also likeclose