service ride control escalade

You search Auto repair manual PDF about service ride control escalade, search results will appear below. If search results do not exist, please search by others keyword.

2001 Pontiac Grand Prix Shifter A/T: Service and Repair

Filed Under (Pontiac) by admin on 31-12-2013

Download 2001 Pontiac Grand Prix V6-3.8L VIN K. Shifter A/T: Service and Repair Shift Control Replacement Removal Procedure 1. Remove the horseshoe clip (1) from front of shift control knob, and remove knob. 2. Remove the Console Trim Plate. 3. Remove the console wiring harness. 4. Remove the console shift control wiring harness. 5. Remove the automatic transaxle range selector cable. 6. Remove the park/lock cable. 7. Remove the console shift control nuts. 8. Remove the console shift control. Installation Procedure 1. Install the console shift control. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the console shift control nuts. ^Tighten the console shift control nuts to 24 Nm (18 ft. lbs.) . 3. install the park/lock cable. 4. Install the automatic transaxle range selector cable. 5. Install the console shift control wiring harness. 6. Install the console wiring harness. 7. Install the Console Trim Plate. 8. Adjust the transaxle range selector cable.… Read More

2003 Cadillac Escalade Code C0660 will reset.

Filed Under (Cadillac) by admin on 20-12-2013

Download Vehicle Application: 2003 Cadillac Escalade 5.3L, Vin T, USA/Canada 2005 Chevrolet Suburban 1500 LS 5.3L, GAS, Vin T 2003 Cadillac Escalade EXT 6.0L 2005 GMC Yukon XL 1500 Slt 5.3L, FLEX, Vin Z 2005 Chevrolet Suburban 1500 LS 5.3L, FLEX, Vin Z Customer Concern: Code C0660 will reset. Tests/Procedures: 1. Check the RTD fuse located in the underhood fuse block. 2. Check for Battery Voltage (B+) on the Orange wire at the automatic level control air compressor pin F. 3. If less than B+ at pin F, check for a wiring and connection problem between the air compressor and the underhood fuse block. 4. Disconnect the compressor leveling module connector and check the resistance from the positive battery voltage circuit of the exhaust solenoid valve and the control circuit of the exhaust solenoid valve. Should be 30-90 ohms. 5. Check for B+ on the Dark Blue wire pin B at the air compressor with the exhaust solenoid commanded off.… Read More

2002 Volvo XC70 Rear Wheel Hub Replacing

Filed Under (Volvo) by admin on 31-12-2013

Download 2002 Volvo XC70 L5-2.4L Turbo VIN 58 B5244T3 Vehicle Level Transmission and Drivetrain Drive Axles, Bearings and Joints Wheel Hub Service and Repair Rear Wheel Hub, Replacing. Special tools: 951 2050 Raise the car Remove the rear wheel the screw for the drive shaft / wheel hub. Removing the rear wheel hub. Remove the brake caliper mounting screws. Hang the caliper up with a piece of wire the locating pin for the brake disc the brake disc the ABS-cable holder the ABS sensor. Hang up the sensor using a piece of wire. Remove the spring strut from the lower control arm Note: the spring strut is slightly compressed. Remove the anti-roll bar from the upper control arm Use a Torx wrench as a counterhold so that the rubber boot is not damaged. Remove the tie rod from the wheel spindle. Angle the tie rod upwards so that the inner mounting for the control arm is exposed the screw holding the lower mounting for the control arm to the sub-frame.… Read More

2000-2004 Audi TT Install Rear Control Arms

Filed Under (Audi) by admin on 23-11-2013

Download Install Rear Control Arms – Audi TT ’00-’04, VW R32 ’04 Stock ride height or close to it, less than 1.5″ lowering Tools Needed: 1. 17mm lug wrench 2. 18mm open end wrench 3. 18mm socket 4. Floor jack Approximate time: 1 to 1.5 hours depending on experience. NOTE: Make sure to have an alignment done after installation. Even though the parts you just received have been put together with stock length adjustment, each car is a little different. Procedure: 1. Chalk the front wheels. 2. Jack up the rear end. 3. Remove the wheel, 17mm lug wrench. 4. Remove upper control arm bolts with a 18mm open end wrench and 18mm socket. 5. The inner control arm bolt is blocked by the sub frame bolt for the differential. Remove sub frame bolt before trying to remove the inner control arm. 6. Insert the new control arms and reuse the same bolts and nuts.… Read More

2005 Chevrolet Chevy K Silverado Panel Cluster Gauge Needle Function

Filed Under (Chevrolet (Chevy)) by admin on 24-02-2014

Download Subject: 07187C — SPECIAL COVERAGE ADJUSTMENT – INSTRUMENT PANEL CLUSTER GAUGE NEEDLE FUNCTION Models: 2003-2004 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT 2005 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT (U.S. ONLY) 2003-2004 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE 2005 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE (U.S.ONLY) 2003-2004 GMC SIERRA, YUKON, YUKON XL 2005 GMC SIERRA, YUKON, YUKON XL (U.S. ONLY) Condition Some customers of all 2003-2004 model year and certain U.S. 2005 model year Cadillac Escalade, Escalade ESV, and Escalade EXT; Chevrolet Avalanche, Silverado, Suburban, and Tahoe; and GMC Sierra, Yukon, and Yukon XL vehicles have reported that one or more of the instrument panel (IP) cluster gauges stick, flutter, or become inoperative. This may cause inaccurate readings, including the speedometer and fuel gauge. Special Coverage Adjustment This special coverage covers the condition described above for a period of 7 years or 70,000 miles (110,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership.… Read More

1999 Ford EXPLORER TRANSMISSION SLIPPING SHIFT/DELAYED

Filed Under (Ford) by admin on 02-04-2014

Download FORD: 1999 EXPLORER, RANGER MERCURY: 1999 MOUNTAINEER 6. Inspect the fluid pan for major contamination. ISSUE Slipping transmission shifts and/or delayed or no •If contamination is minimal, clean the main transmission engagements may occur on some control, but do not replace. vehicles. The Electronic Pressure Control (EPC) •If major contamination is present, perform solenoid may cause stress on the attaching bracket. normal transmission overhaul as required, This stress causes the bracket to break and the including main control replacement. Pay EPC solenoid to back out of its bore causing line particular attention to the condition of the pressure to drop too low or fluctuate, allowing friction plates. Repair as required. friction clutches to slip. 7. After repairs are completed, verify concern has ACTION been fixed. Diagnose and inspect for damaged EPC attachment PART NUMBER PART NAME bracket, and replace the bracket and EPC solenoid with new bracket and revised EPC solenoid.… Read More

PEUGEOT 407 e253 CAR ALARM CONTROL UNIT

Filed Under (Peugeot) by admin on 01-01-2014

Download
LOCATION OF THE CAR ALARM CONTROL UNIT Compact control units and sirens: place under the bonnet on the wheel box on the driver’s side. Modular control units and accessories: place under the dashboard on the driver’s side. CAR ALARM SUPPLY Positive: Connect the Can Bus connector in the kit of accessories supplied with the e253 (see instructions for its connection in following pages). Power is taken from the Red wire (Pos. 1). Negative: Connect the Can Bus connector in the kit of accessories supplied with the e253 (see instructions for its connection in following pages). Earth is taken using the Black wire (pos. 2) IMMOBILISER Starter Motor: Cut the White wire (Pos 3) in the Black 3-pin connector under the steering wheel. ODOMETER Connect to pos 26 (Wire N° 6739) in the black 40 way connector (green part) on the BSI control unit or directly to the ABS control unit under the bonnet next to the battery in pos.… Read More

2000-2004 Ford Focus ZX3 SVT Suspension Kit INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 17-03-2013

DownloadPARTS IN KIT: ITEM # QTY DESCRIPTION SERVICE PART # REPLACEMENT SOURCE 1 2 Spring, rear 2M5Z-5B669-AA Ford Dealer 2 2 Shock, rear 2M5Z-18125-BA Ford Dealer 3 1 Anti-roll bar, rear 1S4Z-5A772-BA Ford Dealer 4 1 Strut, RF 2M5Z-18124-BA Ford Dealer 5 1 Strut, LF 2M5Z-18124-BB Ford Dealer 6 2 Bump stop 2M5Z-3020-AA Ford Dealer 7 2 Spring, front 2M5Z-5310-AA Ford Dealer 8 2 Nut, upper strut piston W700212-S3091 Ford Dealer. TORQUE SPECIFICATIONS: FASTENER TORQUE (ft./lbs.) (EXCEPT WHERE NOTED) Rear shock upper mount nut 13 Rear shock lower mount nut 85 Rear lower control arm to knuckle 85 Rear anti-roll bar to control arm bolts 11 Rear anti-roll bar bushing clamp bolts 35 Upper strut piston nut 35 Strut tower nuts 18 Knuckle to strut bolt 66 Front anti-roll bar link to strut bolt 94 Caliper to Knuckle 21 Wheel nuts 37. REAR SUSPENSION INSTALLATION INSTRUCTIONS: STEP 1: Raise vehicle off ground and support with jack stands.… Read More

Clunk, Bump or Squawk when Vehicle Comes to Complete Stop

Filed Under (Other Manuals) by admin on 02-04-2014

Download 1999-2000 Cadillac Escalade (Old Style) 2002-2004 Cadillac Escalade, Escalade EXT 2003-2004 Cadillac Escalade ESV 1996-1999 Chevrolet 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 Chevrolet 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 Chevrolet Silverado Extended Cab Short Box (New Style) 1999-2004 Chevrolet Silverado 1500 Series Regular Cab (New Style) 2000-2004 Chevrolet 1500 Series Avalanche, Suburban and Tahoe 2001-2004 Chevrolet Silverado 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 Chevrolet Silverado 2500 Series Crew Cab, Short Box (New Style) 1996-1999 GMC 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 GMC 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 GMC Sierra Extended Cab Short Box (New Style) 1999-2004 GMC Sierra 1500 Series Regular Cab (New Style) 2000-2004 GMC 1500 Series Yukon, Yukon XL 2001-2004 GMC Sierra 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 GMC Sierra 2500 Series Crew Cab, Short Box (New Style) 2003-2005 HUMMER H2 with Four Wheel Drive (4WD) or All Wheel Drive (AWD) and One-Piece Propeller Shaft ONLY.… Read More

MIL “ON” WITH DTC U1000 OR U1010 STORED IN ENGINE CONTROL UNIT

Filed Under (Other Manuals) by admin on 09-02-2014

Download APPLIED VEHICLES: 2002 – 2003 Maxima (A33) 2004 – 2006 Maxima (A 34) 2004 – 2006 Titan (A 60) 2004 – 2006 Armada (TA60) 2002 – 2006 Sentra (B15) 2005 – 2006 Frontier (D 40) 2002 – 2006 Altima (L 31) 2005 – 2006 Xterra (N 50) 2005 – 2006 Pathfinder (R51) 2004 – 2006 Quest (V 42) 2003 – 2006 350Z (Z33) 2003 – 2006 Murano (Z50) IF YOU CONFIRM The MIL is “ON” with • DTC U1000 (CAN COMM CIRCUIT) OR • DTC U1010 (CAN COMM) [2006 Models only] stored in the engine control unit, and There are no drivability incidents. DETERMINE IF This bulletin applies by performing steps 1 and 2 of the Service Procedure. ACTIONS If this bulletin applies, there may be excess resistance in certain ground connections: • Clean/re-tighten ECM ground connections. • Clean/re-tighten negative battery cable body connection and battery post connection. • If needed, clean and ensure good contact between the steering member assembly and the left side instrument stay assembly.… Read More

You might also likeclose