Download INCLUDED IN THE KIT: (1) BAK Cover (1) Re-usable Performance Air Filter (1) Filter Raincoat (1) Mounting Post (4) M5x40 Stainless Cap Screws (2) M5x10 Stainless Cap Screws (1) Baron VTX 1800 BAK Backing Plate (1) Baron Backing Plate Adapter (2) 1/4-28 x 1 13/16″ Zinc Hex Bolts (2) 1/4″ Lock Washers (2) Aluminum Filter Spacers (3) M6x16 Hex Flange Bolts (3) External Tooth Washers (1) Reed Valve Block Off Kit BA-2561-00 (1) 3/8″ Nylon Nipple Pre-installed (1) 1/2″ Nylon Nipple Pre-installed TOOLS REQUIRED: Factory Service Manual 3, 4 & 5 mm Allen Wrenches 10, 12 & 14mm Sockets 12 & 14mm Wrenches INSTRUCTIONS: 1. Remove fuel tank per Honda service manual instructions. 2. Remove air filter box by taking out air filter element and the 4 screws around air funnels. 3. Disconnect electrical fitting from the IAT sensor (intake air temp sensor). 4. Disconnect two hoses on back of air box.… Read More
IMPORTANT NOTICE: Statements in this instruction sheet preceded by the following words are of special significance. WARNING Means there is the possibility of injury to yourself or others. CAUTION Means there is the possibility of damage to the part or motorcycle. NOTE Other information of particular importance has been placed in italic type. S&S recommends you take special notice of these items.
INSTALLATION: 1- Remove the stock air cleaner housing according to the Honda® factory service manual. 2- Remove the intake duct control hose from the intake duct control solenoid according to the Honda factory service manual. See Picture 1. 3- Install the rubber vacuum line cap over the intake duct control solenoid fitting. 4- Remove the intake air temp sensor from the air box as shown in Picture 2. 5- Install the intake air temp sensor into the aluminum back plate with the included 10-24 x 1/2″ socket head cap screws as shown in Picture 3 making sure to use Loctite® 243 on the threads.… Read More
Download Some 1997-2002 Expedition 4X4 and 1998-2002 COMPONENTS AS HIGH PRESSURE IS VENTED Navigator 4X4 vehicles equipped with 4-wheel air UNCONTROLLED. suspension, may exhibit repeat air compressor drier If diagnostics lead to compressor/dryer assembly failures. The drier cap may become detached from replacement, use the following service procedure to the drier body, or the drier body may be broken at insure complete and thorough service. the neck near the compressor head. This may be due to incomplete or incorrect system diagnosis that 1. Using the New Generation STAR (NGS) tester, leads to replacement of only the original air vent the compressor/drier assembly. suspension compressor, despite the fact that the compressor is not the root cause of the concern. 2. Using regulated shop air, blow out the air lines Compressor failure in these instances is only a from the drier to the front fill solenoid valve, symptom of an underlying system problem.… Read More
Download 2002 BMW 325I 2.5L 2003 BMW 325I Sport Wagon 2.5L, Eng Des M54, USA Customer Concern: Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible.… Read More
Download FORD F150 INSTALLATION MANUAL – L5681 PG. 2 Thank you and congratulations on the purchase of a Pacbrake air suspension kit. IMPORTANT: This air suspension kit will not increase the GVWR (Gross Vehicle Weight Rating), as the GVWR is determined by the axle rating. Do not exceed the maximum capacity listed by the vehicle manufacturer. Before starting, ensure the application information is correct for the make, model and year of the vehicle you are installing it on. Please read the entire installation manual prior to starting the installation to ensure you can complete the installation once started. Pacbrake recommends using a good quality anti-seize on all fasteners, this will reduce the chances of corrosion of the fasteners, and help facilitate removal if required at a later date. 1 PREASSEMBLY OF THE AIR SPRINGS 1. Install the roll plate (with the rounded end towards the air spring) on to the bottom of the air spring.… Read More
Download Citroen C4 1.6Hdi 2004-2009, Citroen Berlingo 1.6L 2005-2009, Citroen C2 1.6Hdi 2005-2009, Citroen C3 1.6Hdi 2008-2009, Citroen C3 Picasso 1.6Hdi 2009, Citroen C4 Picasso 1.6Hdi 2006-2009, Citroen C5 1.6Hdi 2005-2009, Mini Cooper 1.6Hdi 2007-2009, Mini Cooper Clubman 1.6Hdi 2007-2009, Peugeot 207 1.6 2006-2009, Peugeot 308 1.6 2007-2009, Peugeot 407 1.6 2005-2009, Peugeot Partner 1.6 2006-2009.
Parts list: 1 x Air filter Element. 1 x Silicone Intake Hose. 1 x Flexi Cold Air Hose. 1 x Metal Adaptor Hose. 1 x Literature Pack. Fixing Kit :- 3 x Plastic Tie. 3 x #44 Hose Clamp. 1 x Mounting Bracket. 1 x M6 Nylock Nut. 2 x M6 Flat Washer. 1 x Hex Head Bolt M6x20.
Instruction sheet A2054-768 1. Disconnect the negative terminal from the vehicle battery. 2. To the install induction kit it is necessary to remove the bulkhead trims: 3. Unclip & remove the side cover surrounding the washer bottle etc.… Read More
PREPARING THE VEHICLE: 1. Jack up the rear of the vehicle or raise on a hoist. Support the frame with safety stands so that the wheels hang (fig. 1). Remove the wheels. 2. Position a floor jack at the connecting point of the lower control arm (under the attaching flange bolt) and knuckle (fig. 2). 3. Remove the flange bolt that connects the lower control arm to the knuckle. THE LOWER CONTROL ARM IS UNDER PRESSURE FROM THE COIL SPRING. USE CAUTION DURING THIS STEP FOR SAFETY PURPOSES. 4. Lower the floor jack gradually until tension is released and the coil spring can be removed. It may be necessary to remove the lower shock bolt in order for the lower control arm to move far enough to remove the coil spring. 5. Remove the coil spring. 6. Unbolt and discard the jounce bumper and mounting bolt (fig. 2).
INSTALLING THE AIR SPRING: 1.… Read More
Download Ford : 2000-2007 Taurus 2000-2003 Windstar 2004-2007 Freestar MERCURY: 2000-2005 Sable 2004-2007 Monterey. ISSUE: Some 2000-2007 Taurus, 2000-2005 Sable, 2000-2003 Windstar, and 2004-2007 Freestar/Monterey vehicles, equipped with a 4F50N, AX4N, or AX4S transaxle, may exhibit an erratic fluid level reading on the transaxle dipstick and possible leaks around the filler tube and grommet. The condition may be due to a restricted transaxle vent. ACTION: Repair the transaxle vent restriction by replacing the transaxle vent with a 90° vent stem, small hose clamp, two (2) tie raps, and 24″ (61 cm) of 5/16″ (8 mm) vacuum hose. The 5/16″ (8 mm) vacuum hose will be routed from the 90° vent on the transaxle back to the cowl area, next to the brake master cylinder and tie rapped in place with the end of the hose facing down. Refer to the following Service Procedures. SERVICE PROCEDURE 1. Disconnect the mass air flow (MAF) sensor electrical connector.… Read More
Download The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot underhood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. The AEM Cold Air Systems are 50 states Street Legal (some models and years still pending) and come with complete instructions for ease of installation. Read and understand these instructions BEFORE attempting to install this product. 1) Getting started a) Make sure vehicle is parked on a level surface.… Read More
Download 1999 Chrysler Truck Town & Country LWB FWD V6-3.8L VIN L Vehicle Level Heating and Air Conditioning Air Door Air Door Actuator / Motor Service and Repair Blend Door Actuator Replacement. REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes.… Read More