rsx adjust throttle cable

You search Auto repair manual PDF about rsx adjust throttle cable, search results will appear below. If search results do not exist, please search by others keyword.

1982-2003 Ford Mustangs Double Hook Clutch Quadrant and Clutch Adjustment Kit INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 23-11-2013

Download DOUBLE HOOK QUADRANT INSTALLATION INSTRUCTIONS: STEP 1: At the bellhousing, remove the plastic splash shield. Use a pry-bar to slacken the clutch cable and disconnect it from the clutch fork. STEP 2: Under the dash, pull the end of the cable loose from the quadrant STEP 3: Under the dash there are two plastic parts that make up the factory clutch quadrant mechanism. They are held in place by clips on the end of the shafts. Remove the clips from the end of the shafts. STEP 4: Press the clutch pedal fully to the floor (you may have to pull the carpet aside) and pry the plastic quadrant and springs off. STEP 5: Press the clutch pedal to the floor again. Align the new aluminum quadrant with the shafts and slide the aluminum quadrant on. Center the quadrant in line with the hole where the cable comes through the firewall.… Read More

2002 Chrysler 300M Special GEAR SHIFT CABLE – FLOOR / REMOVAL

Filed Under (Chrysler) by admin on 10-12-2013

Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More

2002-2006 Acura RSX-S Cruise Control Delete Kit Installation Instructions

Filed Under (Acura) by admin on 02-12-2013

Download Part #: KCD01 & KCD02 K20A2/A3/Z1 Cruise Control Delete Kit for K-Powered EG’s, EK’s, DC2′s, & EF’s This kit provides the SOLUTION for eliminating cruise control on throttle bodies found in the 02-06 RSX-S and 02-05 Civic Si while: -Enabling usage of a short OEM throttle cable (Acura 17910-ST7-L01) for swap cleanliness -Eliminating throttle cable/bracket interferences (with fuel lines, hoods, hoses, etc.) -Essentially converting a K20A2/A3/Z1 throttle body into a K20A (Type R) throttle body -Comprised of high quality billet 6061-T6 machined aluminum. 1. MODIFYING THE GSR THROTTLE CABLE 1. Obtain a 94-01 Acura GSR throttle cable (Acura P/N: 17910-ST7-L01). 2. Slide the metal retaining ring off of the throttle cable boot. 3. Use wire-cutting pliers to cut a slit in the retaining ring for removal from the throttle cable. Be cautious not to damage the throttle cable wire when cutting. 4. Use scissors to trim your throttle cable boot as shown.… Read More

Honda GXV340/GXV390 Engine Owners Manual

Filed Under (Honda) by admin on 24-11-2013

Download
LPG CONNECTIONS This engine is certified to comply with U.S. EPA and California ARB emission regulations using the Impco Beam regulator specified in the installation instructions (see below). Honda used this regulator and other specific parts and adjustments to demonstrate compliance with the emission regulations. Adjustable fuel system parts must have U.S. EPA and California ARB approved tamper resistant features to limit the available adjustment after the fuel system is correctly installed. If an equipment manufacturer did not install your engine in a product you will need the installation instructions for the Honda certified system (see below). If you choose not to use the Honda fuel system you must use a system that has been certified by the fuel system manufacturer to be used on this Honda engine. Or if you use a fuel system that is not already certified you must have certification test data satisfactory to the U.S.… Read More

2002-2006 Acura RSX-S Throttle Body To Intake Manifold Adapter

Filed Under (Acura) by admin on 16-01-2014

Download Part #: KIM01 K20A/A2/A3/Z1 Throttle Body To RBC/RRB/RBB Intake Manifold Adapter This adapter provides the SOLUTION for directly bolting up a 02-06 RSX-S/ITR or 02-05 Civic Si/CTR Throttle Body to an Accord Euro R, 06-08 Civic Si, or 04-05 TSX Intake Manifold. Ease of fitment has been confirmed for the following vehicle/engine/mount combinations: -1992-199 5 Honda Civics equipped with a K20 engine and Hasport EGK1 engine mounts -1996-200 0 Honda Civics equipped with a K20/24 engine and Hasport EKK2 engine mounts -1994-200 1 Acura Integras equipped with a K20 engine and Hasport EGK1 engine mounts -2002-200 6 Acura RSX-S/Honda ITRs with a K20 engine and all available engine mounts. 1. PREPARATION 1. Remove the EVAP hose, brake booster hose, PCV hose, vacuum hose, water bypass hoses, throttle cable, fuel lines, fuel injector connectors, IAC valve connector, TP sensor connector, MAP sensor connector, and EVAP canister purge valve connector from your current intake manifold and throttle body setup.… Read More

Honda Civic Racing Intake Manifold Installation Instruction

Filed Under (Honda) by admin on 01-01-2014

Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More

Honda Civic D-series Racing Intake Manifold Manual Installation Instructions

Filed Under (Honda) by admin on 01-01-2014

Download
Part # 307-05-0260 Racing Intake Manifold For Models and Years • 1992-1995 Honda Civic DX/EX (D15B7/D16Z6) • 1996-2000 Honda Civic EX (D16Y8) • 88-91 Honda CRX Si / DX* (*These models will require additional parts)
Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve).
Removal 1. Allow car to cool to ambient temperature. DO NOT attempt to work on warm or hot vehicle. 2. Drain coolant. 3. Relieve fuel pressure by loosening banjo bolt on top of fuel filter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced.… Read More

Honda Goldwing GL1200 Electronic Cruise Control Manual Installation

Filed Under (Honda) by admin on 01-01-2014

Download
1st step. The actuator spool is installed in the CIU housing with the actuator cable. The actuator spool is rotated to fully extend the cable. 2nd step. The dual spool and carburettor cable are installed. The carburettor cable is attached to the lower groove in the dual spool. The other end of the carburettor cable is attached to the carburettors. Note the position of the roll pin. It is nearly contacting the end of the groove in the actuator spool. The free play in the carburettor cable must be adjusted so that the cable outer can be pulled out 2 ~ 3mm before the carburettors start to open. This ensures that the cruise control cannot prevent the carburettors returning to idle. If more free play is allowed the response of the cruise control is compromised. This adjustment of free play is usually performed after final assembly of the CIU is completed and the CIU is in its final location.… Read More

2001-2005 Honda Civic EX Air Intake Manual Installation Instructions

Filed Under (Honda) by admin on 16-02-2014

Download
Bomz Racing 01-05 Honda Civic EX Air Intake Installation Guide Removal of Factory Intake 1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. 2. Disconnect the air temperature sensor electrical connection. 3. Unclip the battery cable from the air inlet duct. 4. Loosen and remove the two bolts that secure the air inlet duct. 5. Remove the air inlet duct. 6. Loosen and remove the four bolts that secure the air intake resonator. 7. Loosen and remove the two bolts that secure the throttle body plenum. 8. Loosen hose clamp that secures the plenum to the throttle body. 9. Using a pair of piers, depress and pull back the hose clamp on the crank case vent at the cam cover. 10. Pull firmly upwards to remove the throttle body plenum. 11. Using a flat blade screwdriver, unclip the wire harness from the resonator. 12. Unclip the throttle cable and cruise control cable, then remove the resonator by pulling upwards.… Read More

Sorento/Sedona Throttle Position Sensor W/3.5L Engine

Filed Under (Kia) by admin on 09-12-2013

Download provides information related to the Throttle Position Sensor (TPS) for Sorento & Sedona models. Some Sorento & Sedona vehicles may exhibit diagnostic trouble codes P0121 and/or P1121. This condition mainly occurs in high ambient or desert areas, and can be related to the occasional increase in contact resistance due to excessive wear of the inner elements of the TP sensor. This bulletin describes the proper service and adjustment procedure for replacing the TP Sensor. – Effective Vehicle Information 2003-2006 Sorento 3.5L 2002-2005 Sedona 3.5L – Parts Information Part Name Previous Part No. New Part No. Throttle Position Sensor 35102 39000 35102 39000FFF – Service Procedure Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly.… Read More

You might also likeclose