1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

1994 Chevy Truck C 1500 Ignition – Timing Connector Location Change

Download 1994 Chevy Truck C 1500 Truck 2WD V6-262 4.3L VIN Z Vehicle Level Maintenance Tune-up and Engine Performance Checks Ignition Timing Technical Service Bulletins Ignition – Timing Connector Location Change. INFORMATION SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1).… Read More

2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More

2005-2009 Ford Focus WHITE FLAKES COMING FROM A/C VENTS

Download FORD: 2007-2009 MKX 2005-2009 Focus 2008-2010 Crown Victoria MERCURY: 2000-2005 Expedition, F-150 2008-2010 Grand Marquis, Mariner Hybrid, 2007-2009 Edge Mariner 2008-2010 Escape Hybrid, Escape LINCOLN: 2008-2010 Town Car 2000-2005 Navigator. This article supersedes TSB 9-19-16 to update the Using compressed air (maximum inlet pressure) 100 Service Procedure. PSI (689 kPa), clean the A/C ducts through the registers and blow off the evaporator core through ISSUE the blower motor opening. Some vehicles may experience white flakes coming NOTE from the A/C vents when the blower motor is THE ENTIRE EVAPORATOR CORE SURFACE engaged. This may be caused by flux utilized in the MUST BE DRY FOR BEST RESULTS. manufacturing process of the evaporator core. NOTE ACTION WHILE PERFORMING THIS PROCEDURE AND Follow the Service Procedure steps to correct the SELECTING DIFFERENT VENT MODES SUCH AS condition. FLOOR / PANEL AND FLOOR / DEFROST, IT SERVICE PROCEDURE MAY BE NECESSARY TO TEMPORARILY START THE ENGINE TO ENABLE MODE DOOR Hazard and Risk Warnings for White Flakes MOVEMENT.… Read More

1996 Chevrolet Chevy K Pickup Ignition Coil Control Circuit High Voltage

Download 1996 Chevrolet Chevy K Pickup – 4WD | Chevy Pickup, GMC Pickup, Suburban, Tahoe, Yukon (VIN C/K) Service Manual DTC P1351 Ignition Coil Control Circuit High Voltage. Circuit Description The enhanced ignition system uses the crank sensor in order to provide the timing input to the VCM. The VCM uses this reference pulse in order to determine the individual ignition spark timing for each cylinder. Once the VCM calculates the ignition timing, the ignition coil module on the IC circuit receives the timing signal. Each timing pulse received by the ignition coil module on the IC circuit triggers the coil module in order to operate the ignition coil. The secondary ignition voltage is induced, and then the secondary ignition voltage is sent to the distributor for distribution to each spark plug. This DTC is a type A DTC. The IC signal voltage ranges from about 0.5 volt to 4.5 volts.… Read More

2000 Chevy Truck S10/T10 Transfer Case Replacement

Download 2000 Chevy Truck S10/T10 Blazer 4WD V6-4.3L VIN W Vehicle Level Transmission and Drivetrain Transfer Case Service and Repair NVG 233/243-NP1 Transfer Case Replacement. Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 7. Remove any wiring harness from the transfer case. 8. Support the transfer case with a transmission jack. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case. 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case.… Read More

2005 Chevy Truck Silverado 1500 Blower Motor Resistor Replacement

Download 2005 Chevy Truck Silverado 1500 2WD V8-5.3L VIN T Vehicle Level Heating and Air Conditioning Blower Motor Resistor Service and Repair Blower Motor Resistor Replacement. BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor. 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.… Read More

2003 Chevy Truck TrailBlazer Cooling System-Electro-Viscous Fan Clutch Operation

Download 2003 Chevy Truck TrailBlazer 2WD L6-4.2L VIN S Cooling System – Electro-Viscous Fan Clutch Operation. Subject: Operating Characteristics of the Electro-Viscous (EV) Fan Clutch and Diagnostic Tips for Cooling Fan Noise, Delayed Transmission Shifts and/or Engine Revving Too High Models: 2004-2006 Buick Rainier 2002-2006 Chevrolet TrailBlazer, TrailBlazer EXT 2006 Chevrolet TrailBlazer SS 2002-2006 GMC Envoy, Envoy XL 2004-2005 GMC Envoy XUV 2002-2004 Oldsmobile Bravada 2005-2006 Saab 9-7X with 4.2L I-6, 5.3L V-8 or 6.0L V-8 Engine (VINs S, P, M, H – RPOs LL8, LM4, LH6, LS2) Date/VIN Breakpoints for Vehicles with New EV Fan Clutch. Vehicles built after and including the Date or VIN Breakpoints listed in the table shown are equipped with the new electro-viscous (EV) fan clutch . Vehicles of any model year listed in “Models Affected” with labor code J3390 (claimed after June 8, 2005) with P/N 15293048 in Claim History may also be equipped with this new EV fan clutch .… Read More

1997 Chevy Truck C Tahoe Interior Lighting Module Locations

Download 1997 Chevy Truck C Tahoe 2WD V8-5.7L VIN R View: Under Center Of Instrument Panel Zoom Sized for Print Interior Lamp Control Module, Remote Control Door Lock Receiver Manufacturer supplied 2 different possible locations. Look for 5 wire connector with wire colors: gray, white, orange, pink & black. #PIT3819: Location of Interior Lamp Control Module – keywords control dim dome electrical entry ground illumination inoperative keyless lens light remort resistor RKE short – (Dec 23, 2005) Subject: Location of Interior Lamp Control Module. Models: 1995-2000 Chevrolet C/K Trucks, Suburban and Tahoe 1995-2000 GMC Yukon and C/K Trucks Classic Body Style Only The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this P1. Condition/Concern When diagnosing a dome lamp concern on one of the vehicles listed above, you may be unable to locate the Interior Lamp Control Module that is called out in the Service Manual.… Read More

2004 Chevrolet Chevy Suburban Gradual Coolant Loss Over Time with No Evidence of Leak Found

Download 2004 Chevrolet Chevy Suburban – 4WD | Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) Service Manual. Information on Gradual Coolant Loss Over Time with No Evidence of Leak Found. Models: 2004-2006 Buick Rainier 2001-2006 Cadillac Escalade Models 2001-2006 Chevrolet Avalanche, Blazer, Silverado, Suburban, Tahoe, TrailBlazer Models 2001-2006 GMC Envoy, Jimmy, Sierra, Yukon Models 2001-2004 Oldsmobile Bravada 2005-2006 Saab 9-7X with 4.8L or 5.3L VORTECĀ® GEN III, GEN IV V8 Engine (VINs V, T, M, B, Z – – RPOs LR4, LM7, LH6, L33, L59) Some vehicles may experience a gradual coolant loss over time. A very low percentage of cylinder head(s) manufactured with an embossed Castech logo may develop a porosity crack in a very specific area. Inspect the cylinder head assembly to determine if the casting was manufactured by Castech. This can be accomplished by inspecting for their casting logo located on top of the intake port, under the rocker arm support rail and in the spring deck cavity portion of the cylinder head.… Read More