replacing a half shaft on a ford escape

You search Auto repair manual PDF about replacing a half shaft on a ford escape, search results will appear below. If search results do not exist, please search by others keyword.

FORD LIMITED SLIP DIFFERENTIAL INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 11-01-2014

Download -IMPORTANT LUBRICANT NOTE- The Auburn Gear limited-slip differential design has been extensively tested with high quality non-synthetic 80W90 hypoid oils treated with GM or Ford friction additives (3 oz. of additive will treat 1 quart of oil). To avoid differential clutch chatter (noise) and for optimum performance, use the oil and additive described above. Use of other additive and oil types may cause differential clutch chatter. Ford Part Number: C8A219B546A GM Part Number: 1052358 PINION SHAFT MODIFICATION Certain “C” clip axle applications with high gear ratios will require pinion shaft modification due to the thickness of the ring gear. The thick ring gear will prohibit the pinion shaft from being removed making “C” clip installation impossible. Use the following procedure to modify the pinion shaft. 1. Modification to be 90º to the pinion shaft lock screw hole as shown. It is recommended that this be accomplished through grinding. 2. Remove sharp edge from modified section by buffing.… Read More

FORD 429-460 BIG BLOCK ENGINE V8 ENGINE MOUNTS INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 01-01-2014

Download KIT CONSISTS OF: No. Qty Part No. Description 1. 1 713014-L DRIVER’S SIDE MOUNT 2. 1 713014-R PASSENGER SIDE MOUNT 3. 2 725002 1/2″-13 LOCK WASHERS 4. 2 725003 1/2″-13 FLAT WASHERS 5. 2 725004 1/2″-13 HEX NUTS 6. 1 FMC001 FORD INSTRUCTION MANUAL. INSTALLATION INSTRUCTIONS: Due to the extreme torque values of the 460 & 429 Ford V8 engines, it will be mandatory that you install a limit strap or straps to the driver’s side and passenger side engine mount. This limiting strap will prevent the engine from torquing beyond the limits of the rubber vulcanization. The straps should be installed with approximately 1/2″ tension reserve. This will permit the engine to torque up to 1/2″ in the motor mount area without causing any problem to the motor mount itself. Warranty on engine mount separation will be void if the limiting straps are not in place. The replacement of the small Ford V8 and straight 6 cylinder engines have become quite popular in Ford trucks.… Read More

2000 Ford F-150 Rear Drive Axle/Differential

Filed Under (Ford) by admin on 01-01-2014

Download 1. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the RH kick panel area. Failure to do so can result in unexpected inflation or deflation of the air springs, which can result in shifting of the vehicle during these operations. Raise and support the vehicle. 2. Remove the wheel and tire assembly. 3. Remove the differential housing cover (4033). ? Drain the lubricant. For additional information, refer to Differential Housing Cover in this section. 4. Remove the brake calipers and discs. 5. Remove the differential pinion shaft (4211). 1. Remove and discard the differential pinion shaft lock bolt. 2. Remove the differential pinion shaft. 6. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers (4N237). 1.… Read More

Ford Escape Power Trailer Wiring Module Installation Instructions

Filed Under (Ford) by admin on 01-01-2014

Download Part 1- Configuring the Trailer Wiring Module As stated in the opening paragraph, and the disclaimer above, many trailing light wiring modules (and the one you probably purchased) are configured for installation on the driver’s side of the vehicle. The installer will have to cut the cables between the module and each pre-fabricated taillight connectors. Step 1.1 – Cut the wires between the module and each pre-fabricated taillight connector at a distance 3 or 4 inches from the module. This will leave you ample wire to re-connect them later, after the wires are run through grommets behind the bumper cover. Part 2 – Remove the Rear Bumper Cover (half way) and grommets. Although the rear bumper cover does not require complete removal, the beginner may wish to remove it to facilitate the routing of wires. At a minimum, all fasteners holding the bumper
cover to the body of the vehicle on the passenger side will need to be removed.… Read More

FORD TORQUE CONVERTER & TRANSMISSION Installation Instructions

Filed Under (Ford) by admin on 06-02-2014

Download REMOVAL Step 1 Before you begin – let vehicle cool for about an hour. Disconnect battery. Raise vehicle and support on jack stands. The higher you raise it, the easier it is to work under. If your installing a new transmission and converter, skip to STEP 3 Step 2 Drain oil from transmission by removing the drain plug. This is a good time to install a TCI® Drain Plug Kit, TCI® #805800. Pans without plug must be slowly removed by freeing one end and allowing bolts on other end to hold pan. The pan will drop down to allow the fluid to run out the end. Use a drain pan to catch fluid. Remove remainder of bolts and slowly lower pan and pour remainder of fluid in drain pan. Replace filter and clean pan and install new pan gasket. (New gaskets and filters available from TCI®). Reinstall pan and torque pan bolts to OEM specs.… Read More

COMP Cams® Ford Timing Set Installation Instructions

Filed Under (Ford) by admin on 09-12-2013

Download Ford Timing Set Installation Instructions Thank you for choosing COMP Cams® products! We know you have options in valve train component selection and we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and also take a moment to review the included limited warranty information. Engine Application High Energy Magnum Hi-Tech Ford V6, 144-200 3223 Ford V6, 171 (2600-2800cc) 3236 Ford V8, 255, 289, 302 & Boss 302, 1965-1988 2120 3120 Ford V8, 289-351W & Boss 302, pre 1972 3220 Ford V8, 302-351W, 1972 & up 3230 Ford V8, 352-428, 1964-1974 3208 2108 3108 Ford V8, 351C, 351M, 400M, 1970-1982 3221 2121 3121 Ford V8, 429-460, 1968-1971 3222 2122 3122 Ford V8, 429-460, 1972-1987 2130 3130 Ford V8, 429-460 w/nine keyway crank gear 2134* Ford V8, 351W, 351W H.O., 1969-¹84 2135 3135 Ford V8, 5.0L 302 H.O., 1980-March 21, 1984 2131 3131 Ford V8, 5.0L 302, 351W, March 22, 1984-1992 2138 3138 Notes: * #2120 or #3120 should not be installed on 351W engines as they are designed for 255, 289, 302 or Boss 302 engines.… Read More

FORD, CHRYSLER, PONTIAC, OLDS WINDAGE TRAY INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 31-12-2013

Download To install studs : Remove a main bolt (main cap can be removed or left in place), tap threads, coat coarse threads with oil, screw stud in by hand, thread 2 main nuts on tray stud and lock them tightly together, lightly tighten tray stud 10-15 ft/lbs (making very sure that double nuts are not slipping or have run into the main cap), remove the 2 main nuts, coat the fine threads with oil, install the stud washer and nut, torque main stud with oil to torque spec of 65 ft/lbs for 7/16″ or 85 ft/lbs for 1/2″ studs, install 1 silver tray adjusting nut on the 3/8″ fine thread with the serrated face towards you (away from the engine). Do all the required studs locations to mount the tray in this fashion. You are now ready to mount the tray assembly. To install tray : Once all necessary tray studs have been installed properly, consult the special considerations section for the initial tray height and correct width, adjust the tray nut to this height, slide tray assembly into place and onto mounting studs, make sure that tray is supported equally by all studs (no wobble), the install the 2nd silver tray nut with the serrations toward the tray and torque with oil to 35 ft/lbs.… Read More

2008 Ford Escape FLUID LEAK TRANSMISSION FLUID COOLER

Filed Under (Ford) by admin on 04-02-2014

Download FORD: MERCURY: 2008 Escape 2008 Mariner This article supersedes TSB 08-16-12 to change the OPERATION DESCRIPTION TIME production fix date. 090904A 2008 Escape/Mariner1.1 Hrs. CD4E Transmission: ISSUE Replace The Transmission Some 2008 Escape and Mariner vehicles (excluding Fluid Cooler, Includes Hybrids) built on or before 5/9/2008 and equipped Time To Remove And with a CD4E transmission may exhibit a fluid leak Install Bumper Cover, from the transmission cooler. Evacuate And Charge Air Conditioning System, Top ACTION Off Transmission Fluid (Do Follow the Service Procedure steps to correct the Not Use With 19700A, condition. 19700A7) DEALER CODING SERVICE PROCEDURE CONDITION BASIC PART NO. CODE Replace the transmission / A/C cooler with a new 19712 07 updated part following Workshop Manual (WSM), Section 412-01. PART NUMBER PART NAME 8L8Z-19712-J Transmission / A/C Cooler WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage IMPORTANT: Warranty coverage limits/policies are not altered by a TSB.… Read More

1998 Ford Contour A/T – CD4E Harsh and Delayed Upshifts/DTC’s Stored

Filed Under (Ford) by admin on 01-01-2014

Download 1998 Ford Contour V6-153 2.5L DOHC VIN L SFI – A/T – CD4E Harsh and Delayed Upshifts/DTC’s Stored. TRANSAXLE – CD4E – HARSH AND DELAYED 1-2/2-3 UPSHIFTS – AFTER TRANSAXLE OR TURBINE SHAFT SPEED SENSOR (TSS) REPLACEMENT – POSSIBLE DIAGNOSTIC TROUBLE CODES (DTC) 628, 642, 645, 646, 647, 648, P0731, P0732, P0734, P0741, AND P1744 FORD: 1994-1997 PROBE 1995-2000 CONTOUR 2001-2002 ESCAPE MERCURY: 1995-2000 MYSTIQUE 1999-2002 COUGAR ISSUE Some vehicles equipped with the CD4E transaxle may exhibit harsh and delayed 1-2/2-3 upshifts along with DTCs for gear ratio errors after the Transaxle or Turbine Shaft Speed sensor (TSS) have been replaced. DTCs may include OBD1 codes 628, 642, 645, 646, 647, 648, or OBD II codes P0731, P0732, P0734, P0741, and P1744. SERVICE PROCEDURE If the condition occurred after replacing the Transaxle or TSS, use the TSS Selection Chart and determine the correct sensor for the vehicle. 1. Remove the existing TSS from the CD4E pump body.… Read More

1997 F150 – Ford Expedition Radio Replacement Installation Instructions

Filed Under (Ford) by admin on 24-11-2013

Download Parts REQUIRED for the install Description Snap on in dash wire harness ** Please read instructions first Radio dash installation kit 1999 Ford F150/Expedition kit Optional parts for this install None. Remove Factory Radio STEP 1 : The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash.… Read More

You might also likeclose