2007 Chevrolet Impala Transmission 1-2 Shift Shudder at Light to Moderate Acceleration

Download Models: 2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission (RPOs MN3, MN7, M15, M76) Supercede: This bulletin is being revised to update parts information. Please discard Corporate Bulletin Number 06-07-30-023B (Section 07 – Transmission/Transaxle) . Condition Some customers may comment on a 1-2 shift shudder at light to moderate acceleration. Typically, the throttle plate angle parameter is 12-20% at time of condition with vehicle speed of approximately 24-40 km/h (15-25 mph). The customer may describe the condition as slip or delayed shift into second. Correction Replace the complete second clutch assembly with service kit, P/N 24240561.… Read More

2000-2007 Ford Taurus ERRATIC FLUID LEVEL READING ON TRANSAXLE DIPSTICK

Download Ford : 2000-2007 Taurus 2000-2003 Windstar 2004-2007 Freestar MERCURY: 2000-2005 Sable 2004-2007 Monterey. ISSUE: Some 2000-2007 Taurus, 2000-2005 Sable, 2000-2003 Windstar, and 2004-2007 Freestar/Monterey vehicles, equipped with a 4F50N, AX4N, or AX4S transaxle, may exhibit an erratic fluid level reading on the transaxle dipstick and possible leaks around the filler tube and grommet. The condition may be due to a restricted transaxle vent. ACTION: Repair the transaxle vent restriction by replacing the transaxle vent with a 90° vent stem, small hose clamp, two (2) tie raps, and 24″ (61 cm) of 5/16″ (8 mm) vacuum hose. The 5/16″ (8 mm) vacuum hose will be routed from the 90° vent on the transaxle back to the cowl area, next to the brake master cylinder and tie rapped in place with the end of the hose facing down. Refer to the following Service Procedures. SERVICE PROCEDURE 1. Disconnect the mass air flow (MAF) sensor electrical connector.… Read More

2005 Chevrolet Malibu Service and Repair

Download Vacuum Brake Booster Check Valve and/or Hose Replacement Removal Procedure 1. Disconnect the brake booster vacuum check valve (1) from the brake booster. 2. If the vacuum check valve (1) needs to be separated from the vacuum hose (3), release and reposition the clamp (2) on the vacuum hose (3) and remove the check valve (1) from the hose (3). 3. If replacing the vacuum check valve (1), remove the grommet (4) from the brake booster and discard the grommet. 4. If removing the vacuum hose (2), take note of the vacuum hose routing then disconnect from the engine intake manifold connection (3) by releasing tension on the vacuum hose clamp (1) and sliding the vacuum hose (2) off the intake manifold connection (3). Installation Procedure Important: A small amount of denatured alcohol can be used as an assembly aid when installing the vacuum check valve and/or grommet. Do NOT use soap.… Read More

Kit Number 57-0662 Installation Instructions

Download Citroen C4 1.6Hdi 2004-2009, Citroen Berlingo 1.6L 2005-2009, Citroen C2 1.6Hdi 2005-2009, Citroen C3 1.6Hdi 2008-2009, Citroen C3 Picasso 1.6Hdi 2009, Citroen C4 Picasso 1.6Hdi 2006-2009, Citroen C5 1.6Hdi 2005-2009, Mini Cooper 1.6Hdi 2007-2009, Mini Cooper Clubman 1.6Hdi 2007-2009, Peugeot 207 1.6 2006-2009, Peugeot 308 1.6 2007-2009, Peugeot 407 1.6 2005-2009, Peugeot Partner 1.6 2006-2009.
Parts list: 1 x Air filter Element. 1 x Silicone Intake Hose. 1 x Flexi Cold Air Hose. 1 x Metal Adaptor Hose. 1 x Literature Pack. Fixing Kit :- 3 x Plastic Tie. 3 x #44 Hose Clamp. 1 x Mounting Bracket. 1 x M6 Nylock Nut. 2 x M6 Flat Washer. 1 x Hex Head Bolt M6x20.
Instruction sheet A2054-768 1. Disconnect the negative terminal from the vehicle battery. 2. To the install induction kit it is necessary to remove the bulkhead trims: 3. Unclip & remove the side cover surrounding the washer bottle etc.… Read More

2007-2008 Toyota Tundra Rear Driveshaft/Propeller Shaft Clunk/Thunk Noise

Download 1. Confirm that the condition is the rear driveshaft clunk/thunk noise. A. Test drive the vehicle and confirm the customer’scomplaint. B. Place the transfer casein 4WDHighwiththe center differential lock ed. Remove the rear driveshaft and test drive the vehicle. Refer to the Technical Information System (TIS), 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Removal” C. Is the clunk/thunk noise eliminated when coming to a stop and/or when accelerating froma stop? •If Yes-Replace rear driveshaft (propeller shaft assembly). Go to Step 2. •If No-This TSB does NOT apply. Continue diagnosis to isolate cause of condition. 2. Install the NEW driveshaft (propeller shaft) assembly. Refer to TSB DL 001-07 for the installation method for 3 joint driveshaftassemb lies on 2007 model year Tundra. Refer to TIS, 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Installation” NOTE Re-usethespacers provided under the center support bearing to ensure the proper alignment of the center support bearing.… Read More

2007 Hyundai Accent Air Intake System Manual Installation Instructions

Download
Removing the stock air inlet system : a) Loosen and remove PCV breather hose from the inlet tube. Loosen the hose clamp at the throttle body. Tools Recommended: Pliers, 10mm Socket. b) Release the harness connector(s) at the ECU by first flipping the retainers up. Then pull up on the harness connectors. c) Remove the three bolts that secure the air box to the vehicle. Remove the air box from the vehicle. Tools Recommended: 10mm Socket. d) Unbolt the four mounting bolts from the ECU to the air box. Tools Recommended: 10mm Socket and Wrench.
Installing the Hyundai Air Intake System : a) When installing the Hyundai Air Intake System, DO NOT completely tighten the hose clamps, heat shield bolts or mounting tab hardware until instructed to do so later in these instructions. Check to see that the inside of the inlet pipes and air filter are clean and free from any foreign objects and/or obstructions.… Read More

2003 Kia Rio CYLINDER HEAD Service and Repair

Download COMPONENT DISASSEMBLY 1. Drain the coolant and disconnect the upper radiator hose. 2. Remove the breather hose (between the air cleaner and the head cover). 3. Remove the air-intake hose. 4. Remove the vacuum hose, fuel hose and coolant hose 5. Remove the cables from the spark plugs . The cables should be removed by holding the boot portion. 6. Remove the ignition coil. 7. Remove the power steering oil pump and bracket. 8. Remove the intake manifold . 9. Remove the heat protector and exhaust manifold assembly. 10. Remove the coolant pump pulley and the crankshaft pulley. 11. Remove the timing belt cover. 12. Remove the timing belt tensioner pulley. 13. Remove the timing belt . 14. Remove the head cover and cam carrier assembly. 15. Remove the cylinder head assembly. The cylinder head bolts should be removed by using Special Tool, Cylinder Head Bolt Wrench, in the sequence as shown in the illustration in two or three steps.… Read More

2001 Buick Regal Power Steering Pump Replacement

Download 2001 Buick Regal V6-3.8L VIN K Vehicle Level Steering and Suspension Steering Power Steering Pump Service and Repair Power Steering Pump Replacement. Removal Procedure 1. Place a drain pan under the vehicle. 2. Remove the accessory drive belt. Refer to Drive Belt Replacement in Engine. 3. Raise and support the vehicle. Refer to Vehicle Lifting . 4. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation. 5. Remove the power steering pressure hose from the power steering pump. Refer to Power Steering Pressure Hose Replacement. 6. Remove the power steering return hose from the power steering pump. Refer to Power Steering Return Hose Replacement. 7. Remove the power steering mounting bolts from the power steering pump. 8. Remove the power steering pump. 9. Remove the power steering pump reservoir from the power steering pump. 10. Transfer the power steering pump pulley. Refer to Power Steering Pulley Replacement Installation Procedure 1.… Read More

2002 Pontiac Grand Prix GT THERMOSTAT REPLACEMENT

Download 2002 Pontiac Grand Prix GT 2002 ENGINE Engine Cooling – Grand Prix THERMOSTAT REPLACEMENT (3.1 L) Tools Required J 38185 Hose Clamp Pliers Removal Procedure 1. Remove the air cleaner intake duct. Refer to AIR CLEANER INTAKE DUCT . 2. Partially drain the cooling system. Refer to Draining and Filling Cooling System . 3. Use the J 38185 in order reposition the hose clamp from the water outlet housing. 4. Remove the radiator inlet hose from the water outlet housing. 5. Remove the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) 6. Remove the water outlet housing bolts. 7. Remove the water outlet housing and gasket. 8. Remove the thermostat. 9. Clean the water outlet housing mating surfaces. Installation Procedure 1. Install the thermostat. 2. Install the water outlet gasket and the water outlet housing. 3. Install the water outlet housing bolts.… Read More