2005 HONDA CR-V DOOR VISORS INSTALLATION INSTRUCTIONS

Download
PARTS LIST Left front door visor Right front door visor Left rear door visor Right rear door visor Installing the Front Door Visor 1. Lower the front door glass completely. Remove the door glass run channel from the door sash in the area shown. Do not remove the glass run channel from the door mirror base or the rear end of the door. AII 27171 TOOLS REQUIRED Isopropyl alcohol Shop towel Masking tape INSTALLATION NOTE: •These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors. Be careful not to damage the paint finish or glass run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours.… Read More

2001 Mazda Truck MPV DX FRONT DOOR DISASSEMBLY/ASSEMBLY

Download 1. Lower or raise the front door glass so that the distance from the top of the front door glass at the rear end to the upper part of the front molding is 185 mm {7.3 in} 2. Disconnect the negative battery cable. 3. Remove the front door trim.4. Disassemble in the order indicated below. 1. Inner handle 2. Front door trim bracket 3. Door screen 4. Front door glass 5. Front manual window regulator 6. Front power window regulator 7. Glass run channel 8. Front door lock 9. Outer handle 10. Door key cylinder 11. Door weatherstrip 12. Door lower weatherstrip 5. Assemble in the reverse order of disassembly. Front Door Glass Disassembly Note 1. Remove the front door glass installation bolts. 2. Slant the front door glass as shown, and remove the front door glass from the inside of the front door. Outer Handle Assembly Note 1. Connect the door key cylinder harness of outer handle as shown.… Read More

1997 Taurus/Sable Shock Absorber Strut Assembly

Download 1. CAUTION: Do not raise vehicle by rear suspension tension strut and bushing (5A952). Damage to strut may result. Raise hoist or jack only enough to contact body. Refer to Section 00-02 . 2. Remove package tray trim panel and loosen but do not remove three nuts retaining the upper rear shock absorber bracket (18192) to body. 3. Raise vehicle. Remove wheel and tire assembly. 4. Remove bolt retaining brake load sensor proportioning valve (2B547) to rear suspension arm and bushing (5500). 5. Remove clip attaching rear brake hose (2282) to shock strut bracket and carefully move rear brake hose out of the way. Disconnect electronic shock actuator, if equipped. 6. Remove stabilizer bar bracket (5486) from body. 7. Remove nut and washer attaching rear stabilizer bar (5A772) to rear stabilizer bar link (5664) and separate rear stabilizer bar from rear stabilizer bar link. 8. Remove nut, washer and rear suspension tie rod bushing (5K897) retaining rear suspension tension strut and bushing to rear wheel spindle (4A013).… Read More

2000-UP FORD FOCUS 4 Door Sedan / Wagon, 3 Door Hatchback Audio Installation Instructions

Download Preliminary: disconnect the negative battery cable. Antenna: the factory antenna is located in the center front of vehicles roof. Radio removal and in-dash installation: note: the factory radio provision is a custom ford double din. When installing an aftermarket din stereo a dash kit is needed. We recommend the scosche fm1375 or fmc1370 installation kit. A set of din removal tools is also needed to remove the factory head unit. We recommend the scosche dt-1 ford din removal tools. 1. Insert ford din removal tools to release clips, pull out stereo, disconnect and remove. Front door speaker installation: note : the factory speaker provision is for a 6 x 8″ speaker. When installing an aftermarket 5 ¼ or 6 ½ speaker, a speaker adapter is required. We recommend the scosche sa68. 1. Extract (7) t-15 torx screws from the perimeter of door panel. 2. Remove screw cover from door opener cup, and extract (1) # 2 philips head screw from behind.… Read More

2009 Honda Civic 4-Doors Accessories Door Visors Installation Manual

Download
TOOLS AND SUPPLIES REQUIRED Isopropyl alcohol Shop towel Masking tape 6 in. Scale
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” NOTE: •Visors may not be legal in all states. Please check the laws of your state. •Be careful not to damage the paint finish and glass run channels when installing the door visors. •Handle the door visors with care. They are not designed to absorb shock or impact. •This door visor kit should only be installed if the ambient air temperature is 60°F (15°C) or above. •To allow the adhesive to cure, do not wash the vehicle for 24 hours. Installing the Rear Door Visor 1. Fully open the left rear door window. 2. Install one bracket (C) and one bracket (D) on the door sash at the measurements shown.… Read More

1996 Audi/Volkswagen Bose Integration Harness

Download 1996-Up Audi / Volkswagen Bose Integration Harness For models amplified without Bose: 1996-03 Audi A4 / 1996-03 Audi A6 2000-01 Audi S4 / 2002-03 Audi S6 Use the White, White/Black, Gray, and Gray/Black speaker wire for the front speaker output and use the Green and Purple RCA’s for the rear speaker outputs. Be sure to connect the Blue/White wire to the aftermarket radio’s amp turn-on wire. The White and Gray RCA’s will not be used. For models amplified with Bose: 1996-03 Audi A4 / 1996-03 Audi A6 1997-03 Audi A8 / 2000-01 Audi S4 2002-03 Audi S6 / 2001-03 Audi S8 2000-03 Audi TT Use the White and Gray RCA’s for the front speaker output and use the Green and Purple RCA’s for the rear speaker outputs. Be sure to connect the Blue/White wire to the aftermarket radio’s amp turn-on wire. The White, White/Black, Gray, and Gray/Black speaker wires will not be used.… Read More

Audi A4 Bluetooth Hands Free Kit Installation Instruction

Download Audi A3 (8P) Sportback, Cabrio Audi A4 (8E) B6, B7 Audi A6 (4B)* Audi TT (8J) Roadster, Coupe´ Audi A4 (8K) Audi A5 (8T) Bluetooth Hands Free Kit Installation Instruction. Installation instruction – A3 (8P), A4 (8E), A6 (4B), TT Please remove the head unit using suitable tools, after removing disconnect the necessary wiring. With a plug & play connection you will complete the fitting of the hands free kit. Please see scheme below. Unlock the connection and put the delivered wiring between the head unit and the connector coming from the vehicle. Wire the loom for the interface connection towards the glove box. Find a suitable location for the interface box within the vehicle. Make sure you will reach the interface at any time (regarding to software updates). ATTENTION: Does the vehicle have airbags fitted along the A-column it is essential to wire the loom for the microphone BEHIND the airbag.… Read More

Ford Focus PRO-FIT Linear Fuel Doors Installation Instructions

Download Tools you will need: ? Ratchet set ? Flathead screwdriver ? Drill and drill bits (for electric locking fuel door only) ? Small file ? Degreaser ? Clear Rags Parts list (items not to scale):1) Fuel door with pull cable attached (pull cable is on electric locking fuel door only) 2) Wiring harnesses (long and short) with actuator (electric locking fuel door only) 3) L-bracket (x 4) 4) Washer (x 4) 5) Nylock nut (x 4) 6) Long hex bolt (x 4) 7) Short hex bolt (x 6) 8) Fuse taps (3 sizes – electric locking fuel door only) 9) Fuse (electric locking fuel door only) 10) Switch (electric locking fuel door only) 11) Sticky pads (electric locking fuel door only) 12) Tie wraps (electric locking fuel door only) 13) Gas cap 14) Wrenches 15) Black strip caulk (not pictured) PRO-FIT Linear Fuel Doors Ford Focus – Installation Instructions Prep WARNING: Do not perform this install near a flame source due to the risk of fire or explosion from gas fumes.… Read More

1994 Audi S4 Rear Differential – Right and Left Side Seal

Download The following describes the procedure I used to remove and replace the right and left side rear differential seals on my 1994 Audi S4. This procedure should apply to the 1992 – 1994 S4 and the 1995-1997 S6 (the left seal process may be different on the ’96-’97 cars) and should be used in conjunction with the Bentley Repair Manual. Right Side Seal 1. Jack up the right rear of the car and support solidly on jackstands. The higher you jack the car, the better the access and the less likely oil will be lost when you remove the seal. 2. Remove the plastic gravel tray (four 13 mm bolts/nuts). 3. It is not necessary to drain the differential oil. When the axle flange and seal are removed, a small amount of oil may drain out. This can be caught in a drain pan. If you do decide to drain the differential oil, remove the fill plug BEFORE removing the drain plugs.… Read More

2007 Toyota Camry Rear Bumper Removal and Replacement

Download REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.… Read More