1997 F150 – Ford Expedition Radio Replacement Installation Instructions

Download Parts REQUIRED for the install Description Snap on in dash wire harness ** Please read instructions first Radio dash installation kit 1999 Ford F150/Expedition kit Optional parts for this install None. Remove Factory Radio STEP 1 : The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash.… Read More

1990 – 1995 Ford Taurus Mercury Sable Radio Replacement Installation Instructions

Download Remove Factory Radio STEP 1 : The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio. This vehicle may have the Ford Premium Sound System installed in the vehicle. When you pull the Ford radio out of the dash, there may be a square connector plugged into the rear of the Ford radio. If there is a square plug, then your vehicle has amplifiers.… Read More

1990-1993 Acura Integra Radio Replacement

Download Remove Factory Radio NOTE : To remove the Honda factory radio, (2) two screws at the rear of the radio must be removed from underneath the radio which can be accessed from behind the radio. The Honda radio is secured to the pocket below the radio and will pull out of the dash connected together as one unit. STEP 1 : Move to the passenger side of the vehicle. The screws that secure the radio/pocket assembly to the dash are at the rear of the radio. The only way to access these screws is to look up at the rear of the radio from the passenger side of the vehicle. With an 8mm socket or phillips screw, locate and remove the screws as can be seen in the photos shown in the NOTE to the left. STEP 2 : Once the screws at the rear of the radio/ pocket assembly have been removed, the radio can be pulled forward out of the dash.… Read More

1994 Ford Mustang Heating and Defrosting REMOVAL AND INSTALLATION

Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More

Audi TT Glove Box Repair

Download Audi TT Glove Box Repair Broken latches, not staying shut, or not opening. The TT glove box has a few issues that are annoying and costly at the dealership. This guide can solve the problems with a short bit of your time, and about $10. Latch Repair To repair your glove box latch all you may need is one set screw from a hardware store, and a matching thread tap. For about $.30 you can buy a stainless steel 8-32 x 5/16″ set screw. If the pins that keep your glove box shut do not spring back out on their own, you may need a couple pieces of special hardware. I used radio control car parts available from most hobby stores. You will need a pack of 4-40 x 3/8″ socket head cap screws that have a hole drilled in them (Team Associated part #6929) and lock nuts (Team Associated part #4449).… Read More

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

1997 BUICK REGAL RADIO REMOVAL AND IN-DASH INSTALLATION

Download Note: the factory radio provision is for a gm oversize radio chassis. An installation kit is recommended for aftermarket installations. We recommend the use of a scosche gm1580 kit for normal installations of din or shaft radios, or gm1590 kit for custom installations of japanese double din iso or 2 stacked din iso radios. 1. Unsnap gear selector trim bezel, unplug and remove the bezel. Extract (2) 10 mm bolts from metal console bracket. 2. Open armrest storage, lift up rubber mat and extract (2) 10 mm bolts from underneath. 3. Extract (2) 10 mm bolts from the front sides of the console, concealed up under the dash. 4. Slide shifter back into low gear, push down on spring- loaded shifter trim and pull complete center console to rear of the vehicle, allowing the center lower dash section (attached) to unsnap from the dash. 5. Extract (1) screw from bottom lower dash panel at right of glove box.… Read More

1994 – 1998 Honda Accord Radio Replacement Installation Instruction

Download
Remove Factory Radio
STEP 1 : The center dash console must be loosened and pulled away in order to gain access to screws securing the plastic dash panel surrounding the radio. Open the center console glove box. At the very bottom is a plastic panel that covers hidden screws. With your fingers or a flat head screwdriver, lift up and remove the plastic panel. Once the panel is removed, locate and remove two (2) phillips screws. STEP 2 : Lift open the drink tray door. Pull the drink tray up and pull it out of the center console.STEP 3 : Once the drink tray is removed, locate and remove three (3) phillips screws. (2) screws will be at the bottom of the panel, and (1) will be at the front left corner near the top of the opening. STEP 4 : Once the three screws have been removed, the center console can be pull back, away from the gear shift console.… Read More

2006 Honda Civic SI Comptech Supercharger Kit Installation Instructions

Download STEP #1 Evacuate A/C system: • Have your local Air conditioning shop remove the HFC-134a refrigerant from your A/C system. They can reuse your coolant. After the supercharger installation you will need to return the car to them and have them refill and charge the system. This service should cost approximately $80.00. STEP #2 Remove ECM and ship to Hondata: • Remove the battery. • Remove ECM cover (A). • Remove bolts (D), then lift up the ECM. • Disconnect the ECM connectors A, B, and C. • Remove ECM and ship to Hondata (see Address to right.) STEP #3 Drain Coolant: • Jack up and support the front of the car on jack stands. • Make sure the engine is cool and remove the radiator cap. • Drain the cooling system by loosening the drain plug (A) at the bottom of the radiator. • Once all of the coolant is drained close the drain plug.… Read More

1997-1999 Buick Century/Regal 99-2001 AW-200GM INSTALLATION INSTRUCTIONS

Download BUICK Century 1997-99 LeSabre 1995-99 1 Park Avenue 1995-99 Regal 1995-99 Riviera 1996-99 Roadmaster 1995-96 Skylark 1996-98 CHEVROLET Impala 2000 Venture 2000 OLDSMOBILE Achieva 1996-98 Aurora 1995-99 Bravada 1998-99 Cutlass 1998-99 Cutlass Supreme 1995-97 Eighty-Eight 1994-99 Intrigue 1998-99 LSS 1996-99 Ninety-Eight 1994-96 Regency 1997-98 Silhouette 2000 PONTIAC Montana 2000 Sunfire 2000. BUICK LeSabre / Park Avenue 1995-99 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the plastic trim piece to the left of the glove box and (1) Phillips screw exposed. Unsnap the top edge of the knee bolster panel. Remove (1) Phillips screw from the panel. Remove the ashtray cluster and (2) Phillips screws from each side. Unclip the entire dash trim bezel and remove. Remove (3) 9/32″ hex-head screws securing the factory head unit and disconnect the wiring. Skip to the Installation Instructions for ALL VEHICLES on Page #6. CHEVROLET Impala 2000 Disconnect the negative battery terminal to prevent an accidental short circuit.… Read More