remove 2007 passat front bumper

You search Auto repair manual PDF about remove 2007 passat front bumper, search results will appear below. If search results do not exist, please search by others keyword.

2007 Toyota Camry Rear Bumper Removal and Replacement

Filed Under (Toyota) by admin on 06-04-2014

  Download 2007 Toyota Camry Rear Bumper Removal and Replacement

Download REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.… Read More

  Download 2007 Toyota Camry Rear Bumper Removal and Replacement

2009 Ford F150 Rear Bumper W1750 Installation Instructions

Filed Under (Ford) by admin on 31-12-2013

  Download 2009 Ford F150 Rear Bumper W1750 Installation Instructions

Download I. Overview Congratulations on your new purchase of the industries’ best and most stylish Rear Bumper available for the 2009 Ford F150! This Bumper has been engineered for strength while keeping the weight down. Your Rear Bumper designed in 3-D from digitized data, CNC laser cut, fabricated, and powder coated… all in the U.S.A. Enjoy the fit and finish of a quality Ford F150 Rear Bumper from Fab Fours Inc. II. Tools Required • Socket Wrench with Extension • Breaker Bar • 3/4″ & 18mm Sockets • Flat and Phillips Head Screw Drivers • 3/4″ Box End Wrench • T20 Torx Bit • Floor Jack and wood block. III. Removal of Stock Bumper A. Unplug the Factory License Plate lights from the back side of the light housing from underneath the truck. Turn counter clockwise until loose. Secure up and out of harm’s way. B. Disconnect the wiring harness from the back up sensors.… Read More

  Download 2009 Ford F150 Rear Bumper W1750 Installation Instructions

2007 Ford Focus Accessories List Guide

Filed Under (Ford) by admin on 01-01-2014

  Download 2007 Ford Focus Accessories List Guide

Download “Mobile-ease™” Hands Free System Connector Wiring Harness Required for Installation of “Mobile-ease™” Hands Free System 3W4Z-14A411-AA 2005-2007 Hands Free System Requires Connector Harness 14A411 for Installation3W4Z-19G399-AA2005-2007 “Street Appearance Package” ZX3/ZX5 Includes Front & Rear Bumper Fascia & Chromed Exhaust Tip, Primed 6S4Z-6120049-AA 2006-2007 ZX4 Includes Front & Rear Bumper Fascia & Chromed Exhaust Tip, Primed 6S4Z-5420049-BA 2006-2007 Bug Shield Styled Smoke-Color (Single-Pack) 5S4Z-16C900-A 2005-2007 Cargo Area Protector 3-Door/5-Door Black 1M5Z-6111600-AA 2001-2007 Sedan Black 1M5Z-5411600-DA 2001-2007 Wagon Black 1M5Z-7411600-CA 2001-2007 Cargo Logic System Without Logo Sedan, Heathered Black Ink (00) 3M5Z-5411600-AA 2003-2007 3-Door Hatchback, Heathered Black Ink (00) 3M5Z-6111600-AA 2003-2007 Wagon, Heathered Pebble (65) 3M5Z-7411600-AA 2003-2007 Wagon, Heathered Flint (64) 3M5Z-7411600-BA 2003-2007 Wagon, Heathered Black Ink (00) 3M5Z-7411600-CA 2003-2007 Cargo Net, Retention 4-Door/Wagon Envelope Style YS4Z-54550A66-AA 2000-2007 Cargo Organizer 3-Door/5-Door/Sedan Black, For Use Without Subwoofer 5M5Z-54115A00-AAA 2005-2007 Cargo Organizer, Interior Wagon Black, With Ford Logo F8CZ-54115A00-BAA 2000-2007 Cargo Security Shade For Wagon, Med.… Read More

  Download 2007 Ford Focus Accessories List Guide

2000-2002 FORD FOCUS ZX3 AVENGER BODY KIT INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 04-03-2014

  Download 2000-2002 FORD FOCUS ZX3 AVENGER BODY KIT INSTALLATION INSTRUCTIONS

Download Cleaning procedure using a paper towel and grease remover or lacquer thinner, thoroughly clean area on car where the double face tape will come in contact with the painted surface. Do not allow thinner or cloth to remain on car too long as it can cause damage to the painted surface. Using either of the recommended adhesion promoters on a clean lint free cloth, apply a thin, uniform coating to the bonding surface, using the minimum amount that will fully coat the surface. Allow promoter to dry completely before attempting installation of the part. 1) front bumper replacement open the hood and remove the factory clips along the center of the factory front bumper. Remove one screw in each wheel well and also remove the two ten millimeter bolts located on the underside of the bumper. Remove the factory front bumper and discard the styrofoam absorber. Remove the grill from the factory bumper and place it on the new wings west front bumper.… Read More

  Download 2000-2002 FORD FOCUS ZX3 AVENGER BODY KIT INSTALLATION INSTRUCTIONS

2009 FIT MUGEN REAR UNDER SPOILER INSTALLATION INSTRUCTION

Filed Under (Honda) by admin on 01-01-2014

  Download 2009 FIT MUGEN REAR UNDER SPOILER INSTALLATION INSTRUCTION

Download NOTE: The rear under spoiler cannot be installed on a vehicle equipped with splash guards. PARTS LIST Rear under spoiler 4 Washer bolts (6 x 15 mm) TOOLS REQUIRED Phillips screwdriver Flat-tip screwdriver Hex wrench Drill 5 mm Allen wrench 3 mm, 6 mm and 10 mm Drill bits Clip remover Center punch Pushpin Airsaw Utility knife Felt-tip pen Scale Masking tape Isopropyl alcohol Shop towel Eye protection Blanket INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” NOTE: •Allow the exhaust pipe to cool down before installing this accessory. •Be careful not to damage the rear bumper and the paint finish. •This rear under spoiler kit should be installed only if the ambient temperature is 60°F (15°) or above.… Read More

  Download 2009 FIT MUGEN REAR UNDER SPOILER INSTALLATION INSTRUCTION

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Filed Under (Chevrolet (Chevy)) by admin on 29-12-2013

  Download 1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

  Download 1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

2006-2007 Buick Lucerne BX1512 Installation Instructions

Filed Under (Buick) by admin on 04-04-2014

  Download 2006-2007 Buick Lucerne BX1512 Installation Instructions

Download Attachment Tabs: Due to the design of the removable tabs, the RangeFinderII and Ambassador tow bars can not be used. Adapters, except the BX8833 and BX88151, can not be used with this baseplate. Installation Instructions: 1. Remove four pushpins from the radiator cover and lift to remove. Do this to both sides of the vehicle. Set pushpins and radiator cover aside to be reinstalled later. 2. Remove three pushpins from the top of the fascia. Do this to both sides of the vehicle. Set pushpins aside to be reinstalled later. 3. Remove five pushpins just forward of the front tire, on the edge of fascia. Do this to both sides of the vehicle. Set pushpins aside to be reinstalled later. 4. Pull wheel well cover aside and remove two metric bolts from back side of fascia using the 10mm socket. Do this to both sides of the vehicle. Set bolts aside to be reinstalled later.… Read More

  Download 2006-2007 Buick Lucerne BX1512 Installation Instructions

2006-2007 HONDA CIVIC 4-DOOR Fog Lights Installation Instructions

Filed Under (Honda) by admin on 09-10-2013

  Download 2006-2007 HONDA CIVIC 4-DOOR Fog Lights Installation Instructions

Download INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. 3. Remove the front bulkhead cover (two expansion clips, three clips and move the right and left fender trims inward). 4. With the help of an assistant, remove the front bumper (four long clips, four center clips, two socket bolts and two self-tapping screws). To prevent damage, set the front bumper on a blanket. 5. Apply masking tape to the front bumper (left side) in the area shown. 6. On the inside of the front bumper, locate the eight marks on the left side of the bumper.… Read More

  Download 2006-2007 HONDA CIVIC 4-DOOR Fog Lights Installation Instructions

2004-2006 Ford Double DIN Installation Kit PART 95-5812 INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 09-12-2013

  Download 2004-2006 Ford Double DIN Installation Kit PART 95-5812 INSTALLATION INSTRUCTIONS

Download FORD Edge 2007-2009 / Expedition 2007-2009 Explorer 2006-2009 / Explorer Sport Trac 2006-2009 F-150 2004-2008 / F Series 2005-2008 Five-Hundred 2005-2007 / Focus 2005-2007 / FreeStar 2004-2007 Freestyle 2005-2007 / Fusion 2006-2009 Mustang 2005-2009 / Super Duty 2008-2009 Taurus 2008-2009 / Taurus X 2008-2009 MERCURY Monterey 2004-2007 / Milan 2006-2008 Montego 2005-2007 / Mountaineer 2006-2009 Sable 2008-2009 LINCOLN Mark LT 2005-2009 Factory Navigation Only: MKX 2007-2009 / Navigator 2007-2009. DASH DISASSEMBLY A B C D E FORD MUSTANG 2005-2009 Remove the small rectangular shifter lever trim panel if equipped . (Figure A) 2 Remove (4) 9/32″screws from the radio to remove. (Figure E) 7 Remove (2) Phillips screws from under the center armrest at the back of the shifter trim panel (includingcup holders). (Figure B) 3 Unclip and remove panel. (Figure B) 4 Unclip and remove the (2) center stack trim panels from the left and right side of the radio and climate controls.… Read More

  Download 2004-2006 Ford Double DIN Installation Kit PART 95-5812 INSTALLATION INSTRUCTIONS

Audi S4 Side Mount Intercooler Installation

Filed Under (Audi) by admin on 02-01-2014

  Download Audi S4 Side Mount Intercooler Installation

Download Lift the car and secure it with jack stands. Ramps will also work. Remove lower engine splash shield. Remove side grilles from bumper. Use a slotted screwdriver through the grille inserts and pry the two tabs behind the inner most edge of each of the inserts. Remove 3 bolts securing each headlight in place. Use caution when removing bolt behind the turn signal bulbs, as they are hard to retrieve if dropped. Disconnect headlight plug. From the turn signal end, pull the headlight forward slightly, and then slide outwards to remove from inner locating dowel. Remove headlight and disconnect turn signal bulb connector. You can also remove the bulb and connector together. Remove two torx screws securing bumper to inner fender liner. One screw per side. Disconnect washer fluid hose Using a 6mm Hex bit, remove bolts (2) securing bumper to bumper shocks. One per side. Pull upwards and outwards on the rear outer corner of the bumper.… Read More

  Download Audi S4 Side Mount Intercooler Installation

You might also likeclose