, search results will appear below. If search results do not exist, please search by others keyword.
Download Vehicle Application: 2000 Mercedes-Benz ML320 3.2L 2001 Mercedes-Benz E320 3.2L 2001 Mercedes-Benz C240 2.6L 2001 Mercedes-Benz E320 4Matic 3.2L 2001 Mercedes-Benz C320 3.2L 2002 Mercedes-Benz ML320 3.2L Customer Concern: Engine light is on with no acceleration. Fault code is P0120. Tests/Procedures: 1. Connect scan tool and monitor voltages of pedal sensor B37. Signal 1 (Accelerator pedal position: Idle speed):[0.2...0.5] V Signal 2 (Accelerator pedal position: Idle speed):[0.1...0.5] V Signal 1 (Accelerator pedal position:Kickdown):[4.3...4.8] V Signal 2 (Accelerator pedal position:Kickdown):[2.1...2.5] V 2. If voltages are out of specification verify correct reference voltage to sensor by measuring between pins 6 (Black/White wire) and pin 1 (Blue/Grey wire) on pedal sensor connector. Voltage needs to be between 4.75 and 5.25 volts. 3. Test throttle body voltages with scan tool. Potentiometer #2 signal voltage ignition on, accelerator pedal position CTP 0.3-0.9 VDC, WOT > CTP value Potentiometer #1 signal voltage Ignition on, accelerator pedal position CTP 4.0-4.6 VDC, WOT < CTP value.… Read More
Download 2001 Mercedes-Benz SLK320 Engine light is on with no acceleration
Download Thirteenfold Auxiliary Relay Panel. Relay location on the thirteen position auxiliary relay panel, above relay panel: Relay Panel: Relay Panel & Thirteenfold Auxiliary Relay Panel Zoom Sized for Print 1 -Auxiliary Emergency Flasher Relay (404) 2 -Relay for Motor Remote Unlock Rear Lid (79) 3 -Starting Interlock Relay (53) (185) (465) 4 -Fog Light Relay (53) 5 -Control Module for Multi-function Steering Wheel (450) 6 -Control Module for Multi-function Steering Wheel (450) 7 -Daytime Running Lights Change-over Relay (173), from April 1999 8 -Daytime Running Lights Change-over Relay (173), through March 1999 9 -Dual Horn Auxiliary Relay (53) 10-Glow Plug Relay (180) 10-Warning Lamp Auxiliary Relay (200) 11-Park/Neutral Position (PNP) Relay (175) 12-Power Supply (Terminal 30, B+) Relay (109) 1 -Dual Horn Relay (53) 2 -Load Reduction Relay (18) (100) 4 -Fuel Pump (FP) Relay (409) V -Wiper/Washer Intermittent Relay (192) (377) (389) VI -Wiper/Washer Intermittent Relay (192) (377) (389) NOTE Number in parentheses ( ) indicates production control number stamped on relay housing.… Read More
Download 2001 Volkswagen Jetta GLS Relay Panel
Download 1. Remove fuel tank filler cap. Listen for fuel pump operation noise at fuel tank filler. Fuel pump should operate for 2 seconds after ignition switch is turned on. If fuel pump operates as specified, fuel pump is okay. If fuel pump does not operate as specified, go to next step. 2. Turn ignition switch off. Remove rear seat or trunk floor to gain access to fuel pump connector. Disconnect fuel pump connector. Disconnect PGM-FI main relay connector. Connect a fused jumper wire between PGM-FI main relay connector FUEL PUMP fuse side terminal and fuel pump side terminal. See L – WIRING DIAGRAMS article. 3. Turn ignition switch on. Using a voltmeter connected to ground, check for battery voltage at fuel pump harness side connector. See L – WIRING DIAGRAMS article. If battery voltage is not present, check harness between fuel pump and FUEL PUMP fuse. Repair as necessary. If battery voltage is present, check fuel pump ground.… Read More
Download 1998 Acura 3.5RL ENGINE PERFORMANCE Basic Diagnostic Procedures
Download •This procedure is completed on a 2006 Mercedes C230 (2.5L V6) •Same Procedure applies for these models: •W203 (2001-2007 C-class) V6 petrol models (C230, C240, C320, C350) •W204 (2008+ C-class) V6 petrol models (C300, C350) •W208, W209 (1998+ CLK V6′s) •W211, W212 (2001+ E-class V6′s) •R170, R171 (2001+ SLK V6′s) •W163, W164 (1998+ M-class V6′s) Time Required: 30 -90 min Tool Required: •Screw Driver with a T25 star head. •Rag for cleaning your hands Step 1: Remove Front Engine Cover (grab both sides and pull straight up; see red arrows) Figure 1 -Removing front engine cover Step 2: Remove Intake air box by disconnecting crankcase vent tube and both intake ducts (removing intake ducts may take some effort and twisting). Once the ducts and tubes are disconnected, pull up on the entireintake air box. Optional: If needed remove cabin A/C cabin filter (Figure 1) Step 3: Turn Intake Air Box over and remove the 8 (T25 star head) screws (red arrows in Figure 5) from the intake air filter chambers.… Read More
Download Mercedes Benz Changing Air Filters on Dual Intake V6
Download 1993 Ford Escort G – TESTS W/CODES – EEC-IV (1.9L)’ ’1993 ENGINE PERFORMANCE Ford Motor Co. – Self-Diagnostics – EEC-IV. CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH) Diagnostic Aids When ignition switch is in the ON or START position, the PCM connects FUEL PUMP circuit (PCM terminal No. 22) to ground. The fuel pump relay is energized and electrical current flows to the fuel pump. If PCM does not receive ignition PIP signal within 2 seconds, FUEL PUMP circuit is opened and fuel pump operation is terminated. Perform this test when instructed by QUICK TEST or CIRCUIT TEST AA. This test is only intended to diagnose: * Fuel pump relay. * Inertia Fuel Shutoff (IFS) switch. * Wiring harness circuits (B+, VPWR, FUEL PUMP, GND and POWER-TO-PUMP). * Faulty Powertrain Control Module (PCM). Fig. 31: Fuel Pump Monitor Circuit Diagram (Escort & Tracer) 1)Code 87/556: Check VPWR To Fuel Pump Relay Code 87/556 indicates a fuel pump primary circuit failure.… Read More
Download 1993 Ford Escort FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH)
Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More
Download 2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More
Download 1997 Honda Civic Alarms Fitting Wiring Diagram Manual Instructions
Download 1985 Mercedes Benz 380SE (126 Chassis) V8-3839cc 3.8L SOHC (116) Lambda System Function Test. Lambda closed loop tester with yellow test wire – 909 589 00 21 00 Oil telethermometer – 116 589 272 100 Test Conditions: Ignition system must be in good working order and engine at idle speed. Ignition timing must be set to specification. Testing Test Procedure Follow test procedure shown in image.… Read More
Download 1985 Mercedes Benz 380SE Lambda System Function Test
These 5 adjustments are not active when a ME-RC Remote Control with revision 1.5 or higher is used. They are set using displays under the AGS button on the remote control. Gen Run Signal (input to pin 2 must be 10 to 40 DC volts only while generator is running); this can be the generator hour-meter or a 12vdc pilot/run light
ME-AGS relay timing for 3-Wire Mode. Magnum Energy, Inc. provides this diagram to assist in the installation of the Auto-Generator Start controller. Since the use of this diagram and the conditions or methods of installation, operation and use are beyond the control of Magnum Energy, Inc., we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of the installation, operation and use of this unit.… Read More
Download Honda Generator EM3800SX EM5000SX ME-AGS Wiring Diagram
Download Honda Civic 2001-2002 Acura RSX 2002. Installation Instructions 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the wiring color guide. 3. Wire the 555I as shown in the wiring diagram. IMMOBILIZER IGNITION FEEDYELLOW/BLACK DATA RED/BLUE KEY SENSE RED/WHITE RED: Connect this wire to a constant (+)12 volt source. BLACK: Connect this wire to a quality chassis ground (preferably scraped sheet metal) separate from other component ground locations. BLUE: Connect this wire to the BLUE status output of the remote start. It must see ground during remote start. BLUE/WHITE: Connect this wire to the (-) key sense wire listed in the Wire Color Guide. It is located in a six-pin molex at the ignition cylinder. The key sense wire rests at ground when the key is inserted into the ignition switch.… Read More
Download 2002 Acura RSX 555I Honda/Acura Immobilizer Bypass Module