2004 Pontiac Grand Prix Blower Motor Inoperative or Intermittent

Download 2004 Pontiac Grand Prix | Grand Prix (VIN W) Service Manual Subject: Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) Models: 2005 Buick Allure (Canada Only), LaCrosse 2004-2005 Pontiac Grand Prix. 2004 Pontiac Grand Prix | Grand Prix (VIN W) Service Manual | Document ID: 1644694 #05-01-39-001A: Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) – (Apr 6, 2005) This bulletin is being revised to update Step 5 of the service procedure. Please discard Corporate Bulletin Number 05-01-39-001 (Section 01 — HVAC). Condition Some customers may comment on an inoperative or intermittent Heating, Ventilation and Air Conditioning (HVAC) blower motor. Others may comment that the blower motor speed may momentarily drop or that the blower motor continues to run after the key is turned off.… Read More

GEMINI 1160RSD Remote Control Alarm Installation Guide

Download
PRE-INSTALLATION CHECKS : (For the Installer) – Disconnect the negative terminal of the battery and only re- connect after the installation is complete. – Remove the cover from the rear of the unit, these allow access to the SW2- SW3. SW1 is located next to the connectors. Arrange the central unit as follows: a. SW1 in position A. Voltage drop sensor activated. SW1 in position B. Voltage drop sensor isolated. This sensor must be isolated if on the vehicle there are loads that can operate once the ignition has been switched off (i.e. cooling fan). b. SW2 in position A o B as shown in central locking diagrams. c. SW3 in position A. Continous signal. SW3 in position B. Intermittent signal. For connecting vehicle’s own horn select position B (intermittent signal). d. To de-activate the passive arming function, cut the YELLOW- GREEN wire loop. WIRING INSTRUCTIONS – Check that all wires of the harnesses are fitted in the correct positions on the connectors (checking against alarm wiring diagrams).… Read More

1994-2001 Integra GSR/Type R Vtec Performance Amplifier Control Installation Instructions

Download Civic EX/Si 92-00, Del Sol Si/VTEC 92-95, Integra GSR/Type R 94-01,Prelude 97-01 S2000. Installation 1. Locate the original ECU. On most cars it is in the passenger side “kick panel” near the passenger’s feet. On the Prelude models, it is on the floor directly below the passenger’s feet. On the S2000 the ECU is located in the left side kick panel. 2. Locate the plugs needed for the VPAC wiring connections by looking at the illustration for your model and year. 3. Mount the VPAC using the “hook and loop” fastener tape to a convenient location on the dash or in the glove box. Route the wires to the ECU location. 4. Follow the instructions for your vehicle to complete the wiring. 5. Reinstall the ECU, ECU cover/kick panel/carpeting in the reverse order of removal. 6. Go have fun with your new VPAC. Civic EX/Si 92-95 and Del Sol SI/VTEC 92-95 1.… Read More

Service 4WD Light Illuminated, DTC C0374 Set (Inspect Wiring Harness to Transfer Case Speed Sensors, Replace Wiring Harness)

Download Models: 2004-2007 Buick Rainier 2003-2006 Chevrolet Avalanche, Suburban, Tahoe 2003-2007 Chevrolet Silverado Classic, TrailBlazer, TrailBlazer EXT 2003-2006 GMC Yukon, Yukon XL 2003-2007 GMC Envoy, Envoy XL, Sierra Classic 2003-2004 Oldsmobile Bravada 2005-2007 Saab 9-7X with Four Wheel Drive or All-Wheel Drive and Active All-Wheel Drive (RPO NP4) or Active Two-Speed (RPO NP8) Transfer Case. Condition Some customers may comment on intermittent illumination of the Service 4WD light. Upon investigation, the technician may find DTC C0374 set. The customer may also comment on intermittent erratic operation of the 4WD or AWD system after driving through rain/snow or simply going through a car wash. Cause The speed sensor signal may have become corrupted. Possible openings in the speed sensor wire insulation (twisted pairs) can allow water intrusion. Also, wire connections contaminated by water may result in short circuits and erroneous speed sensor readings. This most often occurs on the rear speed sensor circuit.… Read More

2008-2009 FORD FOCUS ELECTRONIC CRUISE KIT 250-1840

Download A. Pre-Installation Suggestions 1. It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting. Figure 1 2. Remove the driver side lower dash and kick panels. Remove the steering wheel shroud. Figure 2 B. Install Electronic Module 1. Apply the large supplied piece of double- sided adhesive tape to the Cruise Control Module. 2. Plug in the Main Wiring Harness, Switch Harness, and Pedal Interface Harness onto mating connectors of the Cruise Control Module. Figure 3 3. Place the Cruise Control Module in the secure location behind the driver side dash area as shown in Figure 4 . 4. Route the Pedal Interface Harness through steering column and down to the accelerator. 5. Locate the 6 pin plug and mate connectors on the Pedal Interface Harness. Remove the accelerator 6-pin connector and apply to mating connector of Pedal Interface Harness.… Read More

2008 HONDA CR-V FOG LIGHTS INSTALLATION INSTRUCTIONS

Download PARTS LIST Right fog light Left fog light Fog light harness Fog light switch harness Right trim Left trim Switch Relay Bracket 15Wire ties 4 Wire ties with clip 2 Tapes 8 Self-tapping screws, 5 x 16 mm. Washer bolt, 6 x 16 mm Flange nut, 6 mm Fuse (20A) TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver Flat-tip screwdriver Diagonal cutters Ratchet 10 mm Socket 10 mm Combination wrenches Hook tool Isopropyl alcohol Utility knife Masking tape. INSTALLATION 1. Make sure you have the anti-theft codes for the audio and navigation system (if equipped), and write down the XM radio presets (if equipped). 2. Disconnect the negative cable from the battery. 3. Remove the front bulkhead cover (seven clips). 4. Remove the front bumper (four self-tapping screws, six clips, and two bolts). 5. Remove the five clips from the left inner fender, and pull down the left inner fender. 6.… Read More

2002 Crown Victoria/Grand Marquis Workshop Manual

Download Adjust the blower motor setting to LO and then to HI. * Does the blower motor operate correctly? Yes REPAIR circuit 515 (OG/RD) for a short to ground. TEST the system for normal operation. No GO to R2 . R2 CHECK THE BLOWER MOTOR SPEED CONTROL Blower Motor Speed Control C1308 EATC Module C228b * Does the blower motor operate? Yes INSTALL a new blower motor speed control. TEST the system for normal operation. No GO to R3 . R3 CHECK THE BLOWER MOTOR SPEED CONTROL CIRCUITS FOR AN OPEN Blower Motor Speed Control C1308 Measure the resistance between the blower motor speed control C1308: * pin 1, circuit 269 (LB/OG) and the EATC module C228b pin 10. * pin 2, circuit 752 (YE/RD) and the EATC module C228b pin 23. * pin 3, circuit 754 (LG/WH) and the EATC module C228b pin 24. * Are the resistances less than 5 ohms?… Read More

2008-2010 FORD FOCUS ELECTRONIC CRUISE KIT 250-1840

Download 1. It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting. Figure 1 2. Remove the driver side lower dash and kick panels. Remove the steering wheel shroud. Figure 2 B. Install Electronic Module 1. Plug in the Main Wiring Harness, Switch Harness, and Pedal Interface Harness onto mating connectors of the Cruise Control Module. Figure 3 2. Place the Cruise Control Module in a secure location behind the driver side dash area near the firewall away from moving parts. Secure with supplied wire ties. 3. Route the Pedal Interface Harness through steering column and down to the accelerator. 4. Locate the 6 pin plug and mate connectors on the Pedal Interface Harness. Remove the accelerator 6-pin connector and apply to mating connector of Pedal Interface Harness. Apply the other connector to the accelerator.… Read More

2001 PEUGEOT 306 SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS

Download ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, driver’s side. CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard, driver’s side. POWER SUPPLY + 30: connect to the 2 mm2 RED wire located at the position nr. 1 in the 15 way black connector of the central unit of the central locking placed under the central tunnel. – 31: connect directly to the car body. As alternative, connect directly to the negative pole of the battery. IGNITION WIRE + 15/54: connect to the wire located at the position nr. 5 of the 15 way black connector of the central unit of the central locking placed under the central tunnel. DIRECTION INDICATORS Connect to the WHITE wire at the position nr. 10 and to the BEIGE wire at the position nr. 2 located in the 15 way black connector of the central unit of the central locking placed under the central tunnel.… Read More

1997 – 2002 Ford Econoline GRDP6 Guardian or Guardian II Lift Interlocks Installation Instructions

Download Use the instructions that were included with the original Guardian or Guardian II kit, and make the following modifications: VEHICLE 1 HARNESS – 1997-2002 Econoline with Gas Engine and Transmission Code E or 9 only – This application will not have a Ford OEM Blunt cut wire for “Park”. An auxiliary 4-pin Park Harness (Part # GRDP6) will be needed and the Vehicle 1 Harness will need to be modified. Cut the Orange wire on the Vehicle 1 harness near the connector. Save the grommet, and discard the Orange wire. Locate the Ford gray 4-pin connector located above the transmission bell housing. Separate the connector halves and connect the gray “T” harness connectors from the GRDP6 Harness between them. Drill a 5/8″ hole in the bulkhead flange for the engine cover (see picture). Feed the two green wires through the hole from the engine compartment. Slide the saved grommet onto the harness and secure in the hole.… Read More