2000 Saturn SL2 Conversion Calculator

Download IMPORTANT: The important statement at the beginning of the “Ignition Lock Cylinder removal procedure on page 188 in the 2000/2001 Saturn S-Series Body/Electrical Volume II Service Manual is incorrect. Please cross out the important on that page and write in the following important statement. IMPORTANT: When replacing the ignition lock cylinder only, the passlock relearn procedure is not required. 1. Disconnect negative battery cable. 2. Remove lock cylinder bezel from steering column shroud by carefully prying with a thin bladed screwdriver. Zoom Sized for Print 3. Remove shroud fasteners and remove steering column upper and lower shroud panels. 4. Insert key into ignition lock cylinder and rotate to RUN position. ^If ignition lock cylinder can be rotated to RUN position, continue to step 30. ^If ignition lock cylinder cannot be rotated to RUN position, continue with next step. Zoom Sized for Print 5. Using a light hammer and brass drift, tap lightly on the top side of the ignition housing assembly at the location indicated in the illustration, while trying to turn the ignition key.… Read More

1999 Saturn SL Engine – Driveability Concerns/Cooling System DTC’s Set

Download 1999 Saturn SL1 L4-1.9L SOHC VIN 8 Vehicle Level Powertrain Management Computers and Control Systems Coolant Temperature Sensor/Switch (For Computer) Technical Service Bulletins All Technical Service Bulletins Engine – Driveability Concerns/Cooling System DTC’s Set. SUBJECT: Engine Coolant Temperature Sensor Related Diagnostic Trouble Code(s) and/or the Following Conditions: Hard Start, Erratic Idle, Rough Running. Engine Overheating, Low and/or Leaking Coolant, and/or Service Engine Soon Lamp Illuminated. (Replace Engine Coolant Temperature Sensor with New Design Sensor- P/N 21025106) MODELS AFFECTED: 1991-2001 Saturn S-Series vehicles CONDITION: Customers may comment about various driveability and/or engine operating concerns including: hard start, erratic idle, rough running, engine overheating, low and/or leaking coolant, and/or Service Engine Soon lamp illuminated. CAUSE: This condition may be caused by a cracked engine coolant temperature sensor. CORRECTION: Replace engine coolant temperature sensor, inspect and if necessary replace sensor harness connector. Refer to procedure in this bulletin to replace engine coolant temperature sensor and Parts Requirements for specific parts information.… Read More

2003 Saturn Truck VUE V6-3.0L VIN B Timing Belt: Service and Repair

Download 2003 Saturn Truck VUE V6-3.0L VIN B Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft using the J 42098 until the #1 cylinder is at 60 degrees before top dead center (BTDC). 3. Install the J 42069 Crankshaft Locking Tool. 4. Rotate the crankshaft in the engine rotational direction (clockwise) using the J 42098 until the #1 cylinder is at top dead center (TDC) and tighten the lever arm to the water pump pulley flange. Important: Ensure that the alignment of the crankshaft is not 180 degrees off. The alignment mark must align with the corresponding notches on the rear timing belt cover. 5. Install the 1-2 and 3-4 camshaft locks, the J42069-1 Timing Belt Alignment Kit and the J42069-2. Important: Do not rotate the crankshaft if the camshafts are not locked in place with the 1-2 and 3-4 camshaft locks (J42069-1 and J42069-2).… Read More

2002 Saturn SL DTC P0122

Download The throttle position (TP) sensor is a potentiometer that varies resistance according to changes in throttle plate position. The powertrain control module (PCM) measures the signal voltage from the TP sensor which is a reduced value of the PCM 5-volt reference. The voltage ranges from 0.4 (+/-0.2) volts at 0% throttle position to 4.7 volts at wide open throttle. DTC P0122 sets when the TP sensor signal voltage at the PCM is below the calibrated voltage value. DTC Parameters DTC P0122 will set if TP sensor voltage is less than 0.2 volts when: z The condition exists for longer than 10 seconds. z The ignition is ON. DTC P0122 diagnostic runs continuously with ignition ON. DTC P0122 is a type A DTC. Diagnostic Aids Important If DTC P1635 is set, diagnose that DTC first. 2002 Saturn SL
To locate an intermittent problem, use a scan tool to monitor TP SENSOR voltage with ignition ON, engine OFF.… Read More

1995 Saturn Wagon Ignition Lock Cylinder

Download REMOVAL 1. Remove shroud fasteners (5.5 mm hex head) and remove steering column upper shroud panel. 2. Insert key into ignition lock cylinder and rotate to ACC position. 3. Depress the square locking button on the top of ignition module assembly and slide lock cylinder assembly from ignition module housing. INSTALLATION IMPORTANT : Actuator blade within ignition module housing must be in the ACC position to install lock cylinder assembly. If rotated, replace it to the ACC position using needle nose pliers. Installation is the reverse of Removal.Note: Make sure locking button locks into opening lock cylinder module. Torque steering column lower trim cover bolts to 26 in.lbs. (3 Nm)… Read More

2008-Current Buick Enclave 82541 78218 INSTALLATION INSTRUCTIONS

Download MODEL NO. 82541 78218 APPLICATION: 2007-Current Saturn Outlook 2008-Current Buick Enclave 2007-Current GMC Acadia 2009-Current Chevrolet Traverse. COMPLETE PARTS LIST Part Description Quantity 1. Receiver Assembly (1) 2.2372-04 M12-1/75 x 40 Hex Bolt Cl. 10.9 (6) 3.3730-05 1/2 Conical Washer (6) 4.113129 Instruction Sheet (1). 1. Detach rubber muffler hanger from muffler hook. This will allow the muffler to drop down and allow clearance for the hitch installation. The muffler will go back up in the original location after hitch is installed. 2. On bumper skin, remove cutout at yoke location to allow receiver assembly to fit snug under bumper. 3. Lower the muffler enoughto allow hitch assembly to fit up to mounting points on vehicle frame. 4. Attach hitch assembly frame brackets to existing weldnuts in vehicle frame using M12-1/75 x 40 Hex Bolt Cl. 10.9 #2 and 1/2 Conical Washer #3 supplied in hardware kit. Attach hitch assembly yoke at center to existing weldnuts in vehicle frame using M12-1/75 x 40 Hex Bolt Cl.… Read More

General Motors Accessories Headrest DVD System Display Monitor Inoperative

Download Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps.… Read More

2007 Chevrolet Impala Transmission 1-2 Shift Shudder at Light to Moderate Acceleration

Download Models: 2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission (RPOs MN3, MN7, M15, M76) Supercede: This bulletin is being revised to update parts information. Please discard Corporate Bulletin Number 06-07-30-023B (Section 07 – Transmission/Transaxle) . Condition Some customers may comment on a 1-2 shift shudder at light to moderate acceleration. Typically, the throttle plate angle parameter is 12-20% at time of condition with vehicle speed of approximately 24-40 km/h (15-25 mph). The customer may describe the condition as slip or delayed shift into second. Correction Replace the complete second clutch assembly with service kit, P/N 24240561.… Read More

Ticking or Knocking Type Noise Coming From Engine or Transmission Area

Download Subject: L36, L67, L26, L32, LA1, LX9, MN7, M15 Ticking or Knocking Type Noise Coming From Engine or Transmission Area (Replace Flexplate and Torque Converter) Models: 2005 Buick Park Avenue 2005-2006 Buick Allure (Canada Only), LaCrosse, LeSabre, Rendezvous, Terraza 2005 Chevrolet Impala, Monte Carlo, Venture 2005-2006 Chevrolet Malibu, Malibu Maxx, Uplander 2005 Pontiac Aztek, Bonneville 2005-2006 Pontiac Grand Prix, G6 GTP, Montana SV6 2006 Saturn Relay AWD with 3800 3.8L Series III V6 Engine (VINs K, 1, 2, 4, – RPOs L36, L67, L26, L32) or 3500 3.5L V6 Engine (VINs L, 8 RPO LX9) or 3400 3.4L V6 Engine (VIN E – RPO LA1) and Hydra- Matic(R) 4T65-E Transmission (RPOs MN7, M15) Supercede: This bulletin is being revised to update the pictures for better clarification. Please discard Corporate Bulletin Number 06-06-01-014B (Section 06 – Engine/Propulsion System). Condition Some customers may comment on a ticking or knocking type noise coming from the engine or transmission area.… Read More

Utilizing Tech 2 to Retrieve Part Numbers for Radios, Compact Disc (CD) Changers and Instrument Panel Clusters (IPC)

Download Models: 2000-2008 Passenger Cars and Trucks (Including Saturn) 2003-2008 HUMMER H2 2006-2008 HUMMER H3 2005-2008 Saab 9-7X 2005-2008 Isuzu Conventional Medium Duty Models. This bulletin is being published in conjunction with a GMSPO Parts bulletin GMP04-018 (US only) in order to clarify that the removal of several components solely to obtain part numbers may not always be necessary. Parts numbers for numerous radios, CD changers and I/P clusters are retrievable using a Tech 2®. This eliminates the need to remove the component solely to determine the part number. The part number can typically be found under the “Data Display”, “ID Information” or “Module Information” Menu selection and is titled “8 Digit GM Part Number,” “End Model Part Number” or a similar data parameter. Note that if the component was removed during the diagnostic process, then the part number found on the part label can be used to order the replacement part.… Read More