ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More
Download 1. SAFETY REQUIREMENTS STOP! READ IMPORTANT SAFETY CAUTIONS AND WARNINGS BEFORE PROCEEDING. IMPORTANT SAFETY NOTICE Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the actual installation. 1. Always wear safety glasses for eye protection. 2. Place ignition switch in the OFF position. 3. Always apply the parking brake when working on a vehicle. 4. Block the front and rear tire surface to prevent unexpected vehicle movement. 5. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide. 6. Do not smoke or use flammable items near or around the fuel system. 7. Use chemicals and cleaners in well-ventilated areas. 8. Batteries produce explosive gases, which can cause personal injury.… Read More
Parts List Description Quantity Description Quantity 255 Air Spring 2 3/8-16 Flange Lock Nut 16 Upper Bracket 2 3/8-16 Nylon Insert Nut 4 Lower Bracket 2 Thermal Sleeve 2 Bracket Strap 4 Cable Ties 16 3/8 x 4 Poly Conv 2 Inflation Valve 1 ¼ Tubing 1 Metal Valve Cap 1 3/8-16 x 6 Carriage Bolt 4 3/8-16UNC x 1 Hex Head 2 M10 x 1.25 x 30 Hex Head 2 Elbow ¼ NPT to ¼ 2 3/8 Lock Washer 8 ¼ Tee Piece 2 3/8 Flat Washer 8.
1. PREPARATION: This suspension kit consists of all parts necessary to make a successful installation onto your Vehicle. All parts have been tested thoroughly. Please make sure you take all necessary safety precautions while fitting the kit. Note: you should first read these instructions carefully and then take all parts out of the box and pre-assemble them as far as possible before fitting them onto your vehicle.… Read More
These 5 adjustments are not active when a ME-RC Remote Control with revision 1.5 or higher is used. They are set using displays under the AGS button on the remote control. Gen Run Signal (input to pin 2 must be 10 to 40 DC volts only while generator is running); this can be the generator hour-meter or a 12vdc pilot/run light
ME-AGS relay timing for 3-Wire Mode. Magnum Energy, Inc. provides this diagram to assist in the installation of the Auto-Generator Start controller. Since the use of this diagram and the conditions or methods of installation, operation and use are beyond the control of Magnum Energy, Inc., we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of the installation, operation and use of this unit.
Originally posted 2011-03-05 09:31:35. Republished by Blog Post Promoter… Read More
Preparation and Precaution Before beginning installation, ensure that you have sufficient clearance between the axle and the chassis. Use a jack if necessary. Install at one side of the vehicle at a time. Pay attention to your safety at all times during installation – always use axle stands to support the vehicle! 5.1 Preliminary Step – LSV Spring Length Measurement Vehicles without an antilock braking system have a load sensing valve fitted. This has a spring linkage as shown by Figures 13 to 19 inclusive. Before beginning installation, measure and record the length of the spring from the top mounting bracket to the tip of the linkage rod. 5.2 Attachment of Lower Bracket to Bellow Attach the lower bracket to the bellow as indicated by the diagram of Section 4. Do not fully tighten at this stage because… (i) otherwise it may prove difficult or impossible to slot the U-bolts between the lower plate of the bellow and the lower bracket (in step 4 of section 5.4).… Read More
Download Compatible with: CITROEN C2/C3/C4/C5/C6 & C8 with Blaupunkt/VDO RD4 head unit PEUGEOT with Blaupunkt/VDO RD4 head unit Peugeot 307 (>2005) Peugeot 607 (>2005) Peugeot 807 (>2005) Peugeot 407 (>2005) Peugeot 207 (>2006) Peugeot 308 (>2007) Peugeot 307sw (>2005) Peugeot 407sw (>2005).
Installation Guide: Caution : Before the installation of DMC, you need make sure the cd changer option of Citroen or Peugeot head unit is been set on. Otherwise you need go to dealer to open the cd changer option. 1. Before the installation, power off the car 2. Plug the Digital Music Changer into your car stereo changer port (usually located behind the radio) 3. Insert the USB disk or SD Card (Please consult user manual about setting music files in the USB disk or SD Card) 4. For PC, PSP, MD, Mobile Phone etc aux device, connect it with Aux in port 5. Once the unit is installed, power on the radio, then press the Source button, you will then have the following control: Disk+/Disk-, Next track, Previous track, Fast Forward & Fast Rewind etc.… Read More
Download ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment on the support located on the left of the driver’s side shock absorber column. CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard, driver’s side. POWER SUPPLY + 30: connect to the 3 mm2 RED supply wire of the BSI operating central. – 31: connect directly with a cable terminal to the car body. As alternative, connect directly to the negative pole of the battery. IGNITION WIRE + 15/54: connect to the wire located at the position nr. 4 of the 26 way light blue connector coming out of the BSI operating central. DIRECTION INDICATORS Connect to the wires located at the positions nr. 10 and nr.11 in the 16 way black connector coming out of the BSI operating central. ELECTRIC WINDOWS Negative control signal Windows with automatism To make the windows locking it is necessary to transmit a negative control.… Read More
Download ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, driver’s side. CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard, driver’s side. POWER SUPPLY + 30: connect to the 2 mm2 RED wire located at the position nr. 1 in the 15 way black connector of the central unit of the central locking placed under the central tunnel. – 31: connect directly to the car body. As alternative, connect directly to the negative pole of the battery. IGNITION WIRE + 15/54: connect to the wire located at the position nr. 5 of the 15 way black connector of the central unit of the central locking placed under the central tunnel. DIRECTION INDICATORS Connect to the WHITE wire at the position nr. 10 and to the BEIGE wire at the position nr. 2 located in the 15 way black connector of the central unit of the central locking placed under the central tunnel.… Read More
Preparation and Precaution Before beginning installation, ensure that you have sufficient clearance between the axle and the chassis. Use a jack if necessary. Install at one side of the vehicle at a time. Pay attention to your safety at all times during installation – always use axle stands to support the vehicle! 5. INSTRUCTIONS FOR INSTALLATION The following instructions make reference to the diagrams on pages 16 to 18 inclusive. 5.1 Attachment of Top Plate and Tube to Bellow i. Attach the upper plate to the top of the bellow (i.e. the end without the air inlet / exhaust port) using four countersunk screws—Figures 1 and 2. ii. See Section 5.7 – ” Tube Connection and Disconnection, Cutting and Routing” : Connect a tube to the bellow by pushing the tube into the air inlet port on the underside of the spring and then hand-rotating the tube by one screw turn—Figures 1 and 2.… Read More
VEHICLE APPLICATIONS This comprehensive interface is compatible with the following vehicle manufacturers: CITROEN This interface is designed for use with the majority of Citroen models from 1998 including C3, C5, Berlingo, Saxo, Xsara & Xsara Picasso. This is compatible with the following standard Citroen head units: Models with Philips/VDO Head Unit: 22RC260/65Z, 22RC220/35Z OR Models with Clarion Head Unit: PU2325A, PU2294C, PU2325B, PU2358A, PU2471A This interface is not designed specifically for use with the Citroen Satellite Navigation system, but in some instances it may work. PEUGEOT This Interface is also designed for use with the majority of Peugeot models ranging from ’98. This is compatible with the following standard Peugeot head units; 106, 306 and 806 models with Philips Head Unit 22RC200/35/65 or Clarion Head Unit PU2294A 206/307 models with Philips/VDO Head Unit 22RC260/65Z, 22RC220/35Z or Clarion Head Unit PU2325A, PU2294C, PU2325B, PU2358A, PU2471A 406 models with Clarion Head Unit PU2184A / PU1633A / PU1646A This interface is not designed specifically for use with the Peugeot Satellite Navigation system, but in some instances it may work.… Read More