pcv valve 2003 saturn vue v6

You search Auto repair manual PDF about pcv valve 2003 saturn vue v6, search results will appear below. If search results do not exist, please search by others keyword.

1984-1995 Honda Civic/CRX Positive Crankcase Ventilation (PCV) System

Filed Under (Honda) by admin on 31-12-2013

Download SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe.… Read More

Audi TT A.W.E. Tuning DV1 Diverter Valve

Filed Under (Audi) by admin on 27-12-2013

Download 1.8T Audi TT, VW Golf/Jetta/New Beetle. Step 1: Here’s an overview picture of the transverse 1.8T engine found in the Audi TT, VW Golf/Jetta/New Beetle 1.8T. The 225hp TT engine looks a little different, but the install of the A.W.E. Tuning valve is the same procedure. For picture clarity, and ease of install, the decorative engine cover has been removed. Removing the cover is easily done by twisting the “+” shaped fasteners on the cover 90 degrees. They’ll pop up when free, allowing you to grab the cover and lift it up and out of the engine bay. (New Beetle requires removing 2 10mm nuts hidden under trim caps, and then sliding forward and out) We’ve also removed the PCV damper in the following pictures for clarity. You won’t need to remove this item to install the valve. Installation instructions for A.W.E. Tuning DV1 Diverter Valve For 1.8T Audi TT, VW Golf/Jetta/New Beetle Thank you for purchasing the A.W.E.… Read More

2003 Saturn Truck VUE V6-3.0L VIN B Timing Belt: Service and Repair

Filed Under (Saturn) by admin on 10-12-2013

Download 2003 Saturn Truck VUE V6-3.0L VIN B Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft using the J 42098 until the #1 cylinder is at 60 degrees before top dead center (BTDC). 3. Install the J 42069 Crankshaft Locking Tool. 4. Rotate the crankshaft in the engine rotational direction (clockwise) using the J 42098 until the #1 cylinder is at top dead center (TDC) and tighten the lever arm to the water pump pulley flange. Important: Ensure that the alignment of the crankshaft is not 180 degrees off. The alignment mark must align with the corresponding notches on the rear timing belt cover. 5. Install the 1-2 and 3-4 camshaft locks, the J42069-1 Timing Belt Alignment Kit and the J42069-2. Important: Do not rotate the crankshaft if the camshafts are not locked in place with the 1-2 and 3-4 camshaft locks (J42069-1 and J42069-2).… Read More

1997-2001 Acura Integra Type-R Racing Intake Manifold

Filed Under (Acura) by admin on 03-01-2014

Download Part # 307-05-0290 Racing Intake Manifold for • 1999-2000 Honda Civic Si • 1997-2001 Acura Integra Type-R • 1992-1993 Acura Integra GSR • 1994-1997 Honda Del Sol DOHC VTEC. Removal 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt manifold bracket from engine block and intake manifold. This bracket will not be used in assembly and installation. Remove intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors.… Read More

1999-2003 FORD SUPER DUTY F SERIES HIGH PRESSURE OIL PUMP LEAK

Filed Under (Ford) by admin on 18-12-2013

Download FORD: 1998-2003 E SERIES 1999-2003 SUPER DUTY F SERIES 2000-2003 EXCURSION, F-650, F-750 This article supersedes TSB 03-21-50 to update the WARNING service procedure and illustration. DO NOT REMOVE OR ATTEMPT TO REPAIR A LEAK AT THE PLUG PICTURED IN LOWER LEFT ISSUE CORNER OF FIGURE 1, OR DAMAGE TO THE Some 1998-2003 E-Series, 1999-2003 Super Duty, PUMP WILL RESULT. 2000-2003 Excursion, and 2000-2003 F650/750 1998-2003 E-SERIES HIGH PRESSURE OIL vehicles equipped with a 7.3L Diesel engine may PUMP ACCESS PROCEDURE (DISASSEMBLY) exhibit an oil leak at the high pressure oil pump outlet fittings and/or end plug (see Figure 1). The 1. Remove the Intake Air Resonator. For leak may appear to be a rear main crankshaft seal, additional information, refer to Section 303-12 in oil pan gasket, or other engine oil leak due to the the appropriate Workshop Manual. drain hole machined in the crankcase valley which allows any oil in the valley to run down the back of 2.… Read More

2002 Mercury Sable Upper Intake Manifold

Filed Under (Mercury) by admin on 24-11-2013

Download 1. Remove the air cleaner outlet tube. 2. Remove the pin-type retainers and the accelerator cable splash shield. 3. Disconnect the throttle cable and the cruise control cable. 4. Disconnect the Throttle Position Sensor (TPS) and Idle Air Control (IAC) valve electrical connectors. 5. Disconnect the harness Tom the throttle body stud. 6. Disconnect the Exhaust Gas Recirculation (EGR) vacuum regulator and vacuum supply hoses. 7. Disconnect the Positive Crankcase Ventilation (PCV) and Evaporative Emissions (EVAP) vacuum hoses. 8. Remove the EGR valve. 1 Disconnect the vacuum hose. 2 Remove the nuts. 3 Remove the bolts. 4 Remove the EGR valve. 9. Remove the EGR Vacuum Regulator (EVR) valve. 1 Disconnect the vacuum hose. 2 Disconnect the electrical connector. 3 Remove the bolts. 4 Remove the valve. 10. Remove the eight bolts and the upper intake manifold. * Remove and discard the gaskets. * Clean all mating surfaces. Installation 1.… Read More

2003 Cadillac Escalade Code C0660 will reset.

Filed Under (Cadillac) by admin on 20-12-2013

Download Vehicle Application: 2003 Cadillac Escalade 5.3L, Vin T, USA/Canada 2005 Chevrolet Suburban 1500 LS 5.3L, GAS, Vin T 2003 Cadillac Escalade EXT 6.0L 2005 GMC Yukon XL 1500 Slt 5.3L, FLEX, Vin Z 2005 Chevrolet Suburban 1500 LS 5.3L, FLEX, Vin Z Customer Concern: Code C0660 will reset. Tests/Procedures: 1. Check the RTD fuse located in the underhood fuse block. 2. Check for Battery Voltage (B+) on the Orange wire at the automatic level control air compressor pin F. 3. If less than B+ at pin F, check for a wiring and connection problem between the air compressor and the underhood fuse block. 4. Disconnect the compressor leveling module connector and check the resistance from the positive battery voltage circuit of the exhaust solenoid valve and the control circuit of the exhaust solenoid valve. Should be 30-90 ohms. 5. Check for B+ on the Dark Blue wire pin B at the air compressor with the exhaust solenoid commanded off.… Read More

2003 BMW 325I Sport Wagon Check engine light on and fault codes stored

Filed Under (BMW) by admin on 19-03-2014

Download 2002 BMW 325I 2.5L 2003 BMW 325I Sport Wagon 2.5L, Eng Des M54, USA Customer Concern: Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible.… Read More

1996 Ford Taurus With AXOD-E (AX4S)

Filed Under (Ford) by admin on 09-12-2013

Download 1996 Ford Taurus V6-182 3.0L Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Valve Body Service and Repair Removal and Installation With AXOD-E (AX4S) REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor.… Read More

2003-Current Audi S4 (B6 & B7) Carbonio Intake System

Filed Under (Audi) by admin on 05-12-2013

Download 2003-Current Audi S4 (B6 & B7) Includes Sedan, Avant, & Cabriolet These instructions are applicable to vehicles equipped with either manual or automatic tiptronic transmissions. Step 1: Using a Phillips head (star) screwdriver remove the 2 screws holding the factory air inlet scoop. The location of these screws is marked with arrows right. Once these screws are out, the entire inlet scoop can be pulled out. It is made up of 2 pieces between the front of the car and airbox and may need to be split to get it out. Step 3: Using a flat head screwdriver, pry off the plastic clip that attaches the airbox to the passenger side inner fender. The photo right shows an up-close view of the clip. It is best to pry out its center section and then pry out its perimeter housing. Step 4: Disconnect the wire that leads to the MAF sensor by depressing its fixing clip and by pulling apart.… Read More

You might also likeclose