oldsmobile intrigue engine diagram 2000

You search Auto repair manual PDF about oldsmobile intrigue engine diagram 2000, search results will appear below. If search results do not exist, please search by others keyword.

Vehicles Equipped with a Webasto Sunroof System

Filed Under (Other Manuals) by admin on 16-03-2014

Download Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada.… Read More

2000 Buick Regal Oil Pan Replacement

Filed Under (Buick) by admin on 02-01-2014

Download Tools Required z J 28467-90A Engine Support Adapters z J 28467-B Universal Engine Support Fixture z J 36462-A Engine Support Adapter Leg Set 1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical. 2. Carefully disconnect the throttle body air inlet duct. 3. Remove the engine mount struts from the engine. Refer to Engine Mount Strut Replacement . 4. Remove the drive belt. Refer to Drive Belt Replacement . 5. Install the J 28467-90A , the J 28467-B and the J 36462-A . Do not raise the engine. Refer to Engine Support Fixture . 6. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 7. Disconnect the three-way catalytic converter pipe from the right exhaust manifold. Refer to Catalytic Converter Replacement in Engine Exhaust. 8. Remove the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.… Read More

1997 Buick Century COLD ENGINE TICK OR RATTLE AFTER START-UP

Filed Under (Buick) by admin on 05-04-2014

Download 1997 Buick Century Limited 3.1/3.4L ENG TICK OR RATTLE AFTER COLD START UP COLD ENGINE TICK OR RATTLE AFTER START-UP (REPLACE PISTON/PIN ASSEMBLY) Model(s): 1994-95 Buick Regal 1994-97 Buick Skylark 1994-98 Buick Century 1994-95 Chevrolet Beretta Corsica, Lumina, Monte Carlo 1996-98 Chevrolet Venture 1997-98 Chevrolet Malibu 1993-97 Oldsmobile Cutlass Supreme 1994-96 Oldsmobile Cutlass Ciera 1994-97 Oldsmobile Achieva 1996-98 Oldsmobile Silhouette 1997-98 Oldsmobile Cutlass 1994-98 Pontiac Grand Am, Grand Prix 1996-98 Pontiac Trans Sport with 3100, 3400 V6 Engine (VINs M, E – RPOs L82, LA1) CONDITION Some customers may comment on a ticking type noise that begins shortly after cold engine start-up and gradually diminishes as the engine warms up. In most cases, the noise is gone after five (5) minutes. In severe cases, the noise may not disappear when lhe engine is hot. CAUSE Under normal design tolerances when the piston pin bore is produced at the maximum tolerance and the piston pin is produced at the minimum tolerance (min-max tolerance) trace noise levels can occur.… Read More

1998 Chevrolet Blazer Engine Oil Cooler Hose/Pipe Replacement

Filed Under (Chevrolet (Chevy)) by admin on 12-03-2014

Download 1998 Chevrolet Blazer – 4WD | Blazer, Bravada, Jimmy, S10 Pickup,  Sonoma (VIN S/T) Service Manual | Engine | Engine Mechanical – 4.3L | Repair Instructions. Engine Oil Cooler Hose/Pipe Replacement (4WD) Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6.… Read More

1998 Buick Park Avenue Engine Coolant Consumption or Coolant Leak

Filed Under (Buick) by admin on 20-01-2014

Download Engine Coolant Consumption or Coolant Leak (Inspect For Material Degradation/Replace Intake Manifolds) Models: 1995-1997 Buick Riviera 1995-1999 Buick LeSabre, Park Avenue 1996-1999 Buick Regal 1998-1999 Chevrolet Lumina, Monte Carlo 1995-1996 Oldsmobile Ninety-Eight 1995-1999 Oldsmobile Eighty-Eight 1998-1999 Oldsmobile Intrigue 1995-1999 Pontiac Bonneville 1997-1999 Pontiac Grand Prix with 3.8L Engine (VIN K — RPO L36) Condition Some customers may comment on excessive engine coolant consumption, or an engine coolant leak near or under the throttle body area of the upper intake manifold. Cause Upper intake manifold composite material may degrade around the EGR stove pipe and could result in an internal or external coolant leak. Correction 1. Follow the upper intake manifold removal instructions found in the Engine Unit Repair Section of the Service Information Manual. 2. Refer to the arrow in the illustration of the upper intake manifold above. Inspect the inner diameter of the EGR passage for signs of material degradation.… Read More

Ford Mustang Fuel Injection Conversion

Filed Under (Ford) by admin on 04-05-2012

Download These instructions will provide the basic and necessary information to allow a carbureted 302 to be converted to SEFI Fuel Injection. There are several different types of fuel injection conversions available, however, this instruction will concentrate on the High Output, MASS-AIR setups found on the 92-93 Ford Mustangs. There are two main advantages to using this type of setup. The first advantage is that the computer in the MASS-AIR system will automatically compensate for any engine modifications that have been done prior to the installation of the fuel injection system. The second advantage is that fuel is sent to each cylinder individually only during the appropriate firing cycle, meaning that fuel is sent sequentially to each cylinder only when the spark plug is ready to fire. This makes for an extremely efficient firing cycle . SEFI stands for Sequential Electronic Fuel Injection. This system is complex to be sure, therefore, this instruction is going to skip all the technical mumbo-jumbo, and focus on the bare essentials to install this system properly.… Read More

1999 Saturn SL Engine – Driveability Concerns/Cooling System DTC’s Set

Filed Under (Saturn) by admin on 24-02-2014

Download 1999 Saturn SL1 L4-1.9L SOHC VIN 8 Vehicle Level Powertrain Management Computers and Control Systems Coolant Temperature Sensor/Switch (For Computer) Technical Service Bulletins All Technical Service Bulletins Engine – Driveability Concerns/Cooling System DTC’s Set. SUBJECT: Engine Coolant Temperature Sensor Related Diagnostic Trouble Code(s) and/or the Following Conditions: Hard Start, Erratic Idle, Rough Running. Engine Overheating, Low and/or Leaking Coolant, and/or Service Engine Soon Lamp Illuminated. (Replace Engine Coolant Temperature Sensor with New Design Sensor- P/N 21025106) MODELS AFFECTED: 1991-2001 Saturn S-Series vehicles CONDITION: Customers may comment about various driveability and/or engine operating concerns including: hard start, erratic idle, rough running, engine overheating, low and/or leaking coolant, and/or Service Engine Soon lamp illuminated. CAUSE: This condition may be caused by a cracked engine coolant temperature sensor. CORRECTION: Replace engine coolant temperature sensor, inspect and if necessary replace sensor harness connector. Refer to procedure in this bulletin to replace engine coolant temperature sensor and Parts Requirements for specific parts information.… Read More

FORD 429-460 BIG BLOCK ENGINE V8 ENGINE MOUNTS INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 01-01-2014

Download KIT CONSISTS OF: No. Qty Part No. Description 1. 1 713014-L DRIVER’S SIDE MOUNT 2. 1 713014-R PASSENGER SIDE MOUNT 3. 2 725002 1/2″-13 LOCK WASHERS 4. 2 725003 1/2″-13 FLAT WASHERS 5. 2 725004 1/2″-13 HEX NUTS 6. 1 FMC001 FORD INSTRUCTION MANUAL. INSTALLATION INSTRUCTIONS: Due to the extreme torque values of the 460 & 429 Ford V8 engines, it will be mandatory that you install a limit strap or straps to the driver’s side and passenger side engine mount. This limiting strap will prevent the engine from torquing beyond the limits of the rubber vulcanization. The straps should be installed with approximately 1/2″ tension reserve. This will permit the engine to torque up to 1/2″ in the motor mount area without causing any problem to the motor mount itself. Warranty on engine mount separation will be void if the limiting straps are not in place. The replacement of the small Ford V8 and straight 6 cylinder engines have become quite popular in Ford trucks.… Read More

1997-2000 Ford Engine Miss/Noise at Start-Up On

Filed Under (Ford) by admin on 14-11-2013

Download The AERATechnical Committee offers the following information regarding an engine miss or engine noise, at start-up, on 1997-2000 4.6, 5.4 & 6.8LSOHC engines. This condition has been reported during cold ambient temperatures less than 10°F (-12°C). The cause of this condition may be a roller finger follower(s) being dislodged from the valve. This may result in damage to the camshaft, roller finger follower, valve, retainer, etc. Apparently, the clearance created in the lifters, at the locations with the valves remaining open when the engine is shut off, is sufficient enough to allow the dislodgement. Thicker oil during cold ambient temperatures may not allow fully pressurized oil to reach all locations during initial engine start-up. Aprocedure is now available to service this condition. ACTION: Inspect and replace any worn or damaged engine valve components and install a new retaining clip and lash adjuster for service. Refer to the following Service Procedure for details.… Read More

1998 – 2000 NISSAN FRONTIER KA24 ENGINE

Filed Under (Nissan) by admin on 22-12-2013

Download MIL WITH DTC P0400, P0402, ROUGH IDLE, DRIVABILITY INCIDENTS, DIFFICULTY SETTING EGR SRT. APPLIED VEHICLES: 1998 – 2000 Frontier (D22) with KA24 engine 2000 Xterra (WD22) with KA24 engine APPLIED ENGINE: KA24DE 4 cylinder engine IF YOU CONFIRM: • DTC P0400 (EGR) or P0402 (EGRC-BPT Valve) is stored in the ECM, and/or • The vehicle exhibits rough running or other drivability incidents, and/or • Difficulty in setting the EGR System Readiness Test (SRT) status to CMPLT. ACTION: Clean the intake manifold EGR ports. SERVICE PROCEDURE 1. Remove the throttle chamber assembly and place it aside. • Refer to the EM section of the appropriate Service Manual (ESM). NOTE: It is not necessary to completely remove the throttle chamber assembly. • Only remove harness connectors, cables, and hoses necessary to allow the throttle chamber assembly to be placed aside. • Throttle chamber coolant hoses do not need to be removed. 2.… Read More

You might also likeclose