2008 Honda Accord Windshield Manual Installation Instructions

Download
Vehicle type: Four-door sedan NAGS® numbers*: Windshield part numbers FW2814, solar, third visor, FW2815, solar, FW2816, solar, electrochromatic mirror; front door glass FD23508-09; rear door glass FD23510-11; rear vent glass FV23539-40; and back glass FB23512, solar, heated.
Preparation 1. Always wear eye and hand protection when working with glass. Make sure you have the right glass and moldings and the urethane systems you are about to use are current. Windshield part numbers areFW2814, FW2815, and FW2816. 2. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. 3. Drape a fender cover over the fender and tape up any vulnerable areas on the vehicle to protect against possible damage. Tape up the defroster vents to prevent debris from falling into the openings. 4. Tap the rear view mirror down and off the mirror pad. 5. Remove the windshield-wiper nut covers. 6. Remove the windshield-wiper nuts using a 17-millimeter wrench or socket.… Read More

2008 Ford Fusion Windshield Installation Instructions

Download A. Windshield Preparation 1. Always wear eye and hand protection when working with glass. Make sureyou have the right glass and moldings and the urethane systems you are about to use are current. Windshield part number is DW1622. 2. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. 3. Drape a fender cover over the fender and tape up any vulnerable areas on the vehicle to protect against possible damage. Tape up the defroster vents to prevent debris from falling into the openings. 4. Remove the rearview mirror by removing the underside auto- dimming sensor and tapping the base of the mirror offthe pad. 5. Remove the windshield-wiper nut covers. 6. Remove the windshield-wiper nuts using a 13-millimeter wrench or socket. Move the wiper arm in an up-and-down motion to break it loose from the post, or use a wiper puller.… Read More

2008 Buick Enclave Windshield Installation Instructions

Download 1. Always wear eye and hand protection when working with glass. Make sure you have the right glass and moldings and the urethane systems you are about to use are current. Windshield part numbers are DW1681 and DW1714. 2. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. 3. Drape a fender cover over the fender and tape up any vulnerable areas on the vehicle to protect against damage. Tape up the defroster vents to prevent debris from falling into the openings. 4. To remove the rearview mirror, loosen the 20T Torx set screw at the base and slide the mirror off the pad. 5. Remove the windshield-wiper nut covers. 6. Remove the windshield-wiper nuts using a 15-millimeter wrench or socket. Move the wiper arm in an up-and-down motion to break it loose from the post, or use a wiper puller.… Read More

2006 Honda Ridgeline Windshield Manual Installation Instructions

Download
Vehicle type: Four-door crew-cab pickup NAGS®numbers*: Windshield part numbers FW2538 solar, electro-chromatic mirror, with sunroof, heated wiper-park area; FW2537 solar, with sunroof, heated wiper-park area; FW2536 solar, electro-chromatic mirror, heated wiper-park area; and FW2535 solar, heated-wiper park area; front door glass FD22564-65 F R/L solar; rear door glass FD22566-67 R R/L solar; and back glass FB22675 center slider solar and FB22568 slider
A. Windshield
Preparation 1. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. Note: Always wear eye and hand protection when working with glass. Make sure that you have the right glass and moldings, and that the urethane systems you are about to use are current. Windshield part numbers are FW2538, FW2537, FW2536 and FW2535. 2. Pull the rearview mirror in a downward fashion off the mirror pad. 3. Release the two retainers on the inside of the glove box and pivot the box to expose the wiper-park heater connector.… Read More

Utilizing Tech 2 to Retrieve Part Numbers for Radios, Compact Disc (CD) Changers and Instrument Panel Clusters (IPC)

Download Models: 2000-2008 Passenger Cars and Trucks (Including Saturn) 2003-2008 HUMMER H2 2006-2008 HUMMER H3 2005-2008 Saab 9-7X 2005-2008 Isuzu Conventional Medium Duty Models. This bulletin is being published in conjunction with a GMSPO Parts bulletin GMP04-018 (US only) in order to clarify that the removal of several components solely to obtain part numbers may not always be necessary. Parts numbers for numerous radios, CD changers and I/P clusters are retrievable using a Tech 2®. This eliminates the need to remove the component solely to determine the part number. The part number can typically be found under the “Data Display”, “ID Information” or “Module Information” Menu selection and is titled “8 Digit GM Part Number,” “End Model Part Number” or a similar data parameter. Note that if the component was removed during the diagnostic process, then the part number found on the part label can be used to order the replacement part.… Read More

Audi TT Gen 4 1.8T BCS (Boost Control System) installation instructions

Download Volkswagen Jetta, Golf, GTI and Audi TT installation instructions for the 1.8T engine. Installation Instructions 1) Before starting the installation make sure the vehicle is turned off and the key is removed. 2) Find a suitable location to mount the BCS. In most cases the unit is installed in the opening of the center console near the car stereo. The unit is held in place with the Velcro that is provided. 3) Route the wires through the center console to the driver’s side of the car above the clutch or brake pedal. 4) Remove the windshield wiper blades from the car. 5) Remove the weather stripping found at the back of the engine compartment. Remove the screws on the passenger side of the car from the plastic cover that covers the windshield wiper motor. Remove the plastic windshield cover by lifting up on the passenger side and sliding it towards the back of the car.… Read More

Ford Focus Part Numbers: 60886 24805 77176 Installation Instructions

Download Hitch Shown In Proper Position Wiring Access Location: PC1, 2 Equipment Required: Tin Snips Wrenches: 10mm, 11/16 1. Lower exhaust system at the rubber isolator. Spraying a lubricant on the metal hanger rod and the rubber isolator helps removal. 2. Loosen the heat shield by removing the nuts. Note: heat shield cannot be removed. 3. Trim heat shield around the notch at the attachment hole. SeeFigure 2. 4. Bend heat shield back into position and re-install nuts. 5. Using pull wires, feed spacers (Item 2) and carriage bolts into position (both rail) . Access hole located at end of the frame rail and before the impact bar. Leave pull wire attached. Note: It is much easier if bolt and spacer are not engaged while inserting them into frame, refer to illustration. See Figure 3 6. Install spacer (Item 2) between hitch and frame. Both sides. See Figure 2 7. Raise hitch into position over the exhaust.… Read More

1997-2006 Jeep Wrangler TJ Part Number: 51709 Installation Instructions

Download Install Windshield Brackets Loosen the top screw on the A-Pillar Molding. Use a #40 Torx Driver to remove the outboard bolt that attaches the Sport Bar to the windshield. Slide the Windshield Bracket behind the A Pillar Molding and reinstall the bolt you removed to secure the bracket to the windshield. Re-tighten the top molding screw. Install Tailgate Retainers Locate the left and right Tailgate Retainer Mounts. Place the mounts fl ush with the edge of the tailgate opening. Install the Tailgate Retainer Mounts with two #8 x 1/2″ Pan Head Washer Screws for each mount. If your vehicle does not have holes at this location, align the Tailgate Retainer Mounts fl ush with the edge of the tailgate opening. Then mark the locations of the holes in the mounts, center punch and drill a 1/8″ hole at the marked locations. Install the mounts with two #8 x 1/2″ Pan Head Washer Screws for each mount.… Read More

2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More

Audi V1 Interface and V1 Power Hardwire Installation Guide

Download requirements: • Audi vehicle with CAN bus or CDE interface for instrument cluster radio information. • Steering wheel buttons, TAPE button or additional wired button. • V1 Radar Detector • V1 Direct Power Adapter • 2 straight 4 conductor RJ11 cables (like the ones included with the V1) • A-B USB cable for updating and setup tools: • Radio removal tools (available from ADR) • Trim wedge (available from ADR) • 3M Electrical taps (available from ADR) • Wire strippers/cutters • Flat head screwdriver • Towel • Felt or cloth for rattle protection • Flashlight • Electrical Meter (Volt meter) important: Your Audi owner’s manual specifically states that the installation of non-Audi approved accessories such as radios, radar detectors, telephones, etc. may cause damage to the vehicle, affect the vehicles safety, interfere with the electrical system of the vehicle or affect the validity of the Audi Limited Warranty. The Automotive Data Research Interface is not an approved Audi accessory installation steps: 1 Clean off the area where are you are planning on placing the V1.… Read More