mercury mountaineer vacuum line color code

You search Auto repair manual PDF about mercury mountaineer vacuum line color code, search results will appear below. If search results do not exist, please search by others keyword.

2004 Jeep Grand Cherokee Limited BODY & ACCESSORIES Speed Control

Filed Under (Other Manuals) by admin on 30-11-2013

Download 1. Disconnect vacuum hose at speed control servo and install a vacuum gauge into the disconnected hose. 2. Start engine and observe gauge at idle. Vacuum gauge should read at least ten inches of mercury. 3. If vacuum is less than ten inches of mercury, determine source of leak. Check vacuum line to engine for leaks. Also check actual engine intake manifold vacuum. If manifold vacuum does not meet this requirement, check for poor engine performance and repair as necessary. 4. If vacuum line to engine is not leaking, check for leak at vacuum reservoir. To locate and gain access to reservoir, refer to Vacuum Reservoir REMOVAL / INSTALLATION . Disconnect vacuum line at reservoir and connect a hand-operated vacuum pump to reservoir fitting. Apply vacuum. Reservoir vacuum should not bleed off. If vacuum is being lost, replace reservoir. 5. Verify operation of one-way check valve and check it for leaks.… Read More

2002 Mercury Sable Upper Intake Manifold

Filed Under (Mercury) by admin on 24-11-2013

Download 1. Remove the air cleaner outlet tube. 2. Remove the pin-type retainers and the accelerator cable splash shield. 3. Disconnect the throttle cable and the cruise control cable. 4. Disconnect the Throttle Position Sensor (TPS) and Idle Air Control (IAC) valve electrical connectors. 5. Disconnect the harness Tom the throttle body stud. 6. Disconnect the Exhaust Gas Recirculation (EGR) vacuum regulator and vacuum supply hoses. 7. Disconnect the Positive Crankcase Ventilation (PCV) and Evaporative Emissions (EVAP) vacuum hoses. 8. Remove the EGR valve. 1 Disconnect the vacuum hose. 2 Remove the nuts. 3 Remove the bolts. 4 Remove the EGR valve. 9. Remove the EGR Vacuum Regulator (EVR) valve. 1 Disconnect the vacuum hose. 2 Disconnect the electrical connector. 3 Remove the bolts. 4 Remove the valve. 10. Remove the eight bolts and the upper intake manifold. * Remove and discard the gaskets. * Clean all mating surfaces. Installation 1.… Read More

Direct Connect iPod Adapter Ford Explorer / Sport Trac / Mercury Mountaineer Installation Instructions

Filed Under (Ford) by admin on 14-12-2013

Download Contents 1 Congratulations / Contact info 2 Radio Connection 2 Radio Configuration 3 Parts List 3 Tools Required 4 Radio / Adapter Installation Guide 13 Satellite Receiver Connection 13 Satellite Configuration 14 Parts List 14 Tools Required 15 Satellite / Adapter Installation Guide Congratulations / Contact info You’ve purchased a Brandmotion iPod Adapter System designed, engineered, and built specifically for your Ford vehicle. We have made every effort to ensure that your Brandmotion iPod Adapter meets the highest quality standards in terms of fit, durability, finish and ease of installation. Radio Connection This section pertains to Ford Explorer / Sport Trac / Mercury Mountaineer vehicles that do not have a factory-installed satellite receiver. To install the iPod Adapter you will need to access the back of the OEM radio in your vehicle. Specific instructions for removing the trim in your vehicle are included in this guide. If you are not confident that you can safely remove your interior trim to perform the installation, contact your dealer or a competent mechanic for assistance.… Read More

2003 BMW 325I Sport Wagon Check engine light on and fault codes stored

Filed Under (BMW) by admin on 19-03-2014

Download 2002 BMW 325I 2.5L 2003 BMW 325I Sport Wagon 2.5L, Eng Des M54, USA Customer Concern: Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible.… Read More

2005 Chevrolet Malibu Service and Repair

Filed Under (Chevrolet (Chevy)) by admin on 09-12-2013

Download Vacuum Brake Booster Check Valve and/or Hose Replacement Removal Procedure 1. Disconnect the brake booster vacuum check valve (1) from the brake booster. 2. If the vacuum check valve (1) needs to be separated from the vacuum hose (3), release and reposition the clamp (2) on the vacuum hose (3) and remove the check valve (1) from the hose (3). 3. If replacing the vacuum check valve (1), remove the grommet (4) from the brake booster and discard the grommet. 4. If removing the vacuum hose (2), take note of the vacuum hose routing then disconnect from the engine intake manifold connection (3) by releasing tension on the vacuum hose clamp (1) and sliding the vacuum hose (2) off the intake manifold connection (3). Installation Procedure Important: A small amount of denatured alcohol can be used as an assembly aid when installing the vacuum check valve and/or grommet. Do NOT use soap.… Read More

ATS Wastegated 6.9L & 7.3L 093 Turbo Upgrade Kit Installation Instructions

Filed Under (Ford) by admin on 31-12-2013

Download IMPORTANT : It is very important to read all the instructions carefully prior to any installation of your turbo system. Normal mechanical and safety procedures should be followed. l. Disconnect both batteries at the negative terminals. 2. Remove the air cleaner and the air cleaner canister from the engine. 3. Remove the 1/2″ nut holding the wire loom clamp to the rear engine lifting bracket. 4. Remove the rear engine lifting bracket. 5 On the 1983-1992 year models, the vacuum block located above the right bank valve cover (passenger side) needs to be unbolted from fire wall. Then, if the vehicle has sound insulating blanket covering the fire wall, you must remove one half or approximately 14″ off the passenger side using a utility knife. If there is any insulation that is left hanging loose, it should be retained to the fire wall using the screws removed from the passenger side.… Read More

1997 Explorer/Mountaineer Intake Manifold Service and Repair

Filed Under (Ford) by admin on 12-12-2013

Download 1. Disconnect the battery ground cable. 2. Remove the air cleaner outlet tube; refer to Section 303-12 3. Disconnect the ignition coil electrical connector and the noise suppressor electrical connector. 4. Disconnect the idle air control (IAC) electrical connector. 5. Disconnect the EGR backpressure transducer electrical connector. 6. Disconnect the EVR solenoid electrical and vacuum connectors. 7. Disconnect the brake booster vacuum hose from the upper intake manifold. 8. Disconnect the vacuum connector from the upper intake manifold. 9. Disconnect the vacuum connector from the fuel pressure regulator and remove the vacuum harness from the engine. 10. Disconnect the throttle position (TP) sensor electrical connector. 11. Disconnect the hoses from the EGR backpressure transducer ports. 12. Disconnect the six spark plug wires from the spark plugs. 13. Disconnect the spark plug wires from the seven retaining clips. 14. Remove the four ignition coil bolts and the ignition coil from the upper intake manifold.… Read More

2008 Ford Super Duty F-Series Accessories List DESCRIPTION

Filed Under (Ford) by admin on 18-03-2014

Download “Mobile-ease™” Hands Free System Connector Wiring Harness Required for Installation of “Mobile-ease™” Hands Free System 3W4Z-14A411-AA 2005-2008 Hands Free System Requires Connector Harness 14A411 for Installation3W4Z-19G399-AA2005-2008 Bed Hooks, Retractable Stainless Steel XC3Z-99000A64-AA 2000-2008 Black E-Coat XC3Z-99000A64-BA 2000-2008 Bed Mats Long Bed, Styleside, With Ford Logo F81Z-99112A15-AA 1999-2008 Short Bed, Styleside, With Ford Logo F81Z-99112A15-BA 1999-2008 Bed Rail Caps, Diamond Plate Short Bed, With Stake Pocket Holes F81Z-99291A40-CAA 1999-2008 Long Bed, With Stake Pocket Holes F81Z-99291A40-DAA 1999-2008 Bedliner/Bedmat Tailgate Cover F75Z-99000A38-AA 1999-2008 Bedliners** With Ford Logo For Styleside 8.0′ Bed F81Z-9900038-AA 1999-2008 For Styleside 6.5′ Bed F81Z-9900038-BA 1999-2008 Bug Shield Low Profile Smoke-Color (Single-Pack) 8C3Z-16C900-A 2008 Smoke-Color (Bulk Pack of 10) 8C3Z-16C900-B 2008 Smoke-Color (Bulk Pack of 25) 8C3Z-16C900-C 2008 Mini Chrome-Color (Single-Pack) 8C3Z-16C900-D 2008 Chrome-Color (Bulk Pack of 10) 8C3Z-16C900-E 2008 Chrome-Color (Bulk Pack of 25) 8C3Z-16C900-F 2008. Deflectors, Side Window Crew Cab 4-Piece Set, Smoke-Color (Single-Pack) F81Z-18246-CA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 10) YC3Z-18246-HA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 25) YC3Z-18246-JA 1999-2008 Regular Cab 2-Piece Set, Smoke-Color (Single-Pack) F81Z-18246-AA 1999-2008 2-Piece Set, Smoke-Color (Bulk Pack of 10) YC3Z-18246-BA 1999-2008 2-Piece Set, Smoke-Color (Bulk Pack of 25) YC3Z-18246-CA 1999-2008 Super Cab 4-Piece Set, Smoke-Color (Single-Pack) F81Z-18246-BA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 10) YC3Z-18246-EA 1999-2008 4-Piece Set, Smoke-Color (Bulk Pack of 25) YC3Z-18246-FA 1999-2008 Floor Mats, All Weather Molded Vinyl Front & Rear, 3-Piece Set, Front With Vehicle Logo Super Cab, Ebony 8C3Z-2613300-B 2008 Crew Cab, Ebony 6C3Z-2813300-A 2002-2008 Front Pair, With Vehicle Logo Reg.… Read More

Honda Civic Racing Intake Manifold Installation Instruction

Filed Under (Honda) by admin on 01-01-2014

Download Additional Parts List and Installation Notes for CRX Installation Parts Required • 95-95 Civic throttle body and gasket. • 92-95 Civic fuel rail (use 88-91 civic injectors). • 92-95 Civic throttle cable and bracket. • 88-91 CRX intake gasket. • 3 1/2 Feet of vacuum line. • 2 Feet of 3/8″ water hose for “IAC” (lines need to be lengthen). • 1 Vacuum line “T” (to re-connect purge control valve). Notes • There is no need to reinstall the fast idle valve; located on the drivers side of the rear of stock manifold ( there is no check engine light). • Due to engine mounting tolerances, the firewall may need to be clearanced. • The stock intake pipe will not fit. An aftermarket intake pipe will need to be purchased. • Modify stock map sensor / purge control valve bracket for clearance of TPS. • Use 88-91 CRX injectors and fuel regulator.… Read More

1994 AUDI UrS4 Stainless Steel Brake Flex Line Installation

Filed Under (Audi) by admin on 05-04-2014

Download Rear Line Installation I started with the right rear line since this is first in the bleeding sequence. The rear line (see Photo 1) has one threaded female flare fitting (connects to steel brake line) and one threaded male fitting (connects to the caliper). Break both fittings loose on the line on the car. Also break loose the bleeder screw on the caliper before proceeding to avoid the embarrassment of getting the new line on and not being able to bleed it. The caliper connection should come loose easily but the connection to the steel line may give some trouble on rust belt cars. Use your favorite penetrating oil on both. I had to use the flame wrench on one of my connections. Front Line Installation The front flex lines have threaded female flare connections at both ends that connect to steel brakes lines – one from the master cylinder and the other from the caliper.… Read More

You might also likeclose