mercedes c240 engine code po153

You search Auto repair manual PDF about mercedes c240 engine code po153, search results will appear below. If search results do not exist, please search by others keyword.

2001 Mercedes-Benz SLK320 Engine light is on with no acceleration

Filed Under (Mercedes-Benz) by admin on 26-11-2013

Download Vehicle Application: 2000 Mercedes-Benz ML320 3.2L 2001 Mercedes-Benz E320 3.2L 2001 Mercedes-Benz C240 2.6L 2001 Mercedes-Benz E320 4Matic 3.2L 2001 Mercedes-Benz C320 3.2L 2002 Mercedes-Benz ML320 3.2L Customer Concern: Engine light is on with no acceleration. Fault code is P0120. Tests/Procedures: 1. Connect scan tool and monitor voltages of pedal sensor B37. Signal 1 (Accelerator pedal position: Idle speed):[0.2...0.5] V Signal 2 (Accelerator pedal position: Idle speed):[0.1...0.5] V Signal 1 (Accelerator pedal position:Kickdown):[4.3...4.8] V Signal 2 (Accelerator pedal position:Kickdown):[2.1...2.5] V 2. If voltages are out of specification verify correct reference voltage to sensor by measuring between pins 6 (Black/White wire) and pin 1 (Blue/Grey wire) on pedal sensor connector. Voltage needs to be between 4.75 and 5.25 volts. 3. Test throttle body voltages with scan tool. Potentiometer #2 signal voltage ignition on, accelerator pedal position CTP 0.3-0.9 VDC, WOT > CTP value Potentiometer #1 signal voltage Ignition on, accelerator pedal position CTP 4.0-4.6 VDC, WOT < CTP value.… Read More

1998 Chevrolet Blazer Engine Oil Cooler Hose/Pipe Replacement

Filed Under (Chevrolet (Chevy)) by admin on 12-03-2014

Download 1998 Chevrolet Blazer – 4WD | Blazer, Bravada, Jimmy, S10 Pickup, ┬áSonoma (VIN S/T) Service Manual | Engine | Engine Mechanical – 4.3L | Repair Instructions. Engine Oil Cooler Hose/Pipe Replacement (4WD) Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6.… Read More

1999 Saturn SL Engine – Driveability Concerns/Cooling System DTC’s Set

Filed Under (Saturn) by admin on 24-02-2014

Download 1999 Saturn SL1 L4-1.9L SOHC VIN 8 Vehicle Level Powertrain Management Computers and Control Systems Coolant Temperature Sensor/Switch (For Computer) Technical Service Bulletins All Technical Service Bulletins Engine – Driveability Concerns/Cooling System DTC’s Set. SUBJECT: Engine Coolant Temperature Sensor Related Diagnostic Trouble Code(s) and/or the Following Conditions: Hard Start, Erratic Idle, Rough Running. Engine Overheating, Low and/or Leaking Coolant, and/or Service Engine Soon Lamp Illuminated. (Replace Engine Coolant Temperature Sensor with New Design Sensor- P/N 21025106) MODELS AFFECTED: 1991-2001 Saturn S-Series vehicles CONDITION: Customers may comment about various driveability and/or engine operating concerns including: hard start, erratic idle, rough running, engine overheating, low and/or leaking coolant, and/or Service Engine Soon lamp illuminated. CAUSE: This condition may be caused by a cracked engine coolant temperature sensor. CORRECTION: Replace engine coolant temperature sensor, inspect and if necessary replace sensor harness connector. Refer to procedure in this bulletin to replace engine coolant temperature sensor and Parts Requirements for specific parts information.… Read More

2000 Buick Regal Oil Pan Replacement

Filed Under (Buick) by admin on 02-01-2014

Download Tools Required z J 28467-90A Engine Support Adapters z J 28467-B Universal Engine Support Fixture z J 36462-A Engine Support Adapter Leg Set 1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical. 2. Carefully disconnect the throttle body air inlet duct. 3. Remove the engine mount struts from the engine. Refer to Engine Mount Strut Replacement . 4. Remove the drive belt. Refer to Drive Belt Replacement . 5. Install the J 28467-90A , the J 28467-B and the J 36462-A . Do not raise the engine. Refer to Engine Support Fixture . 6. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 7. Disconnect the three-way catalytic converter pipe from the right exhaust manifold. Refer to Catalytic Converter Replacement in Engine Exhaust. 8. Remove the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.… Read More

Ford Mustang Fuel Injection Conversion

Filed Under (Ford) by admin on 04-05-2012

Download These instructions will provide the basic and necessary information to allow a carbureted 302 to be converted to SEFI Fuel Injection. There are several different types of fuel injection conversions available, however, this instruction will concentrate on the High Output, MASS-AIR setups found on the 92-93 Ford Mustangs. There are two main advantages to using this type of setup. The first advantage is that the computer in the MASS-AIR system will automatically compensate for any engine modifications that have been done prior to the installation of the fuel injection system. The second advantage is that fuel is sent to each cylinder individually only during the appropriate firing cycle, meaning that fuel is sent sequentially to each cylinder only when the spark plug is ready to fire. This makes for an extremely efficient firing cycle . SEFI stands for Sequential Electronic Fuel Injection. This system is complex to be sure, therefore, this instruction is going to skip all the technical mumbo-jumbo, and focus on the bare essentials to install this system properly.… Read More

FORD 429-460 BIG BLOCK ENGINE V8 ENGINE MOUNTS INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 01-01-2014

Download KIT CONSISTS OF: No. Qty Part No. Description 1. 1 713014-L DRIVER’S SIDE MOUNT 2. 1 713014-R PASSENGER SIDE MOUNT 3. 2 725002 1/2″-13 LOCK WASHERS 4. 2 725003 1/2″-13 FLAT WASHERS 5. 2 725004 1/2″-13 HEX NUTS 6. 1 FMC001 FORD INSTRUCTION MANUAL. INSTALLATION INSTRUCTIONS: Due to the extreme torque values of the 460 & 429 Ford V8 engines, it will be mandatory that you install a limit strap or straps to the driver’s side and passenger side engine mount. This limiting strap will prevent the engine from torquing beyond the limits of the rubber vulcanization. The straps should be installed with approximately 1/2″ tension reserve. This will permit the engine to torque up to 1/2″ in the motor mount area without causing any problem to the motor mount itself. Warranty on engine mount separation will be void if the limiting straps are not in place. The replacement of the small Ford V8 and straight 6 cylinder engines have become quite popular in Ford trucks.… Read More

2007 Honda Accord CR-V and Civic Remote Engine Starter FAQ

Filed Under (Honda) by admin on 02-01-2014

Download
Model Information Release date for Accord Remote Starter System: September 20, 2007 Release date for CR-V and Civic Remote Starter System: End of September 2007 Technical Questions Q: What does the Honda Remote Engine Starter System do? A: The Honda Remote Engine Starter is a two-way remote system that starts and stops your vehicle’s engine anywhere within a 200-foot range. It’s designed to warm up your vehicle in the winter and cool it down in the summer. Q: How much is the Honda Remote Engine Starter? A: Approximately $499.00 without installation for all applicable Honda models. Check with your Honda dealer for the installation cost. Q: Can I install it myself? A: AHM does not recommend that customers install the Honda Remote Engine Starter due to the complexity of its electrical components. Authorized Honda Technicians are professionally trained to safely install the Remote Engine Starter. Q: Can I have my neighborhood audio shop install the Honda Remote Engine Starter?… Read More

2002 Ford Escort Cooling System Draining, Filling and Bleeding Workshop Manual

Filed Under (Ford) by admin on 25-01-2014

Download Draining 1. Bring the engine to normal operating temperature and turn the engine off. With the cooling system under pressure, inspect cooling system hoses and clamped hose connections for leaks, excessive deterioration or contact wear. Inspect radiator installation retention. Note any discrepancies and proceed. 2. WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap.… Read More

1997 – 2001 Infiniti Q45 ENGINE WILL NOT START

Filed Under (Infiniti) by admin on 24-12-2013

Download 2000 – 2001 I30 (CA33) 1999 I30 (CA32) 1999.5 – 2001 QX4 (JR50) 1997 – 2001 Q45 (FY33) 2000 – 2001 G20 (P11) APPLIED VINS: All APPLIED DATES: Start of production SERVICE INFORMATION This bulletin describes and introduces new features of the Infiniti Vehicle Immobilizer System/Nissan Anti-Theft System (IVIS/NATS). The system is standard equipment on each of the applied vehicles listed above. The IVIS/NATS will not allow the engine to start without the use of a registered ignition key. If a vehicle will not start and the Security lamp is on solid, it may be because the ignition keys were not properly registered into the vehicle’s NATS IMMU (Immobilizer control unit). In this case, there will be a “DIFFERENCE OF KEY” code stored in the NATS IMMU. When the NATS ignition key, IMMU, or ECM (ECCS control unit) are replaced, C/U initialization is necessary. It is also necessary when registering keys and as part of many NATS Service Manual diagnostic procedures.… Read More

2006 FORD FOCUS MIDGET ENGINE OWNERS MANUAL

Filed Under (Ford) by admin on 05-01-2014

Download 1. COOLING SYSTEM The Focus Midget engine is equipped with an opposite rotation water pump impeller, and the water pump pulley turns in the opposite direction when compared to the street version of the engine. This does not reverse the coolant flow through the engine, it simply allows the pulley to be driven with the HTD belt instead of using the back-side of a serpentine belt. No modifications to the water pump impeller or water pump pulley are allowed. Coolant exits the head at the cast elbow located at the rear of the engine, and enters the engine at the pump. Since the engine runs on methanol, and the compression ratio has not been raised, excessive heat is generally not a problem. Therefore, a standard Midget-type radiator has proven more than adequate. High pressure, racing radiator caps have not been needed to maintain acceptable temperatures, 16 lb. caps have been adequate.… Read More

You might also likeclose