2004 Pontiac Grand Prix Blower Motor Inoperative or Intermittent

Download 2004 Pontiac Grand Prix | Grand Prix (VIN W) Service Manual Subject: Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) Models: 2005 Buick Allure (Canada Only), LaCrosse 2004-2005 Pontiac Grand Prix. 2004 Pontiac Grand Prix | Grand Prix (VIN W) Service Manual | Document ID: 1644694 #05-01-39-001A: Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) – (Apr 6, 2005) This bulletin is being revised to update Step 5 of the service procedure. Please discard Corporate Bulletin Number 05-01-39-001 (Section 01 — HVAC). Condition Some customers may comment on an inoperative or intermittent Heating, Ventilation and Air Conditioning (HVAC) blower motor. Others may comment that the blower motor speed may momentarily drop or that the blower motor continues to run after the key is turned off.… Read More

2002 Crown Victoria/Grand Marquis Workshop Manual

Download Adjust the blower motor setting to LO and then to HI. * Does the blower motor operate correctly? Yes REPAIR circuit 515 (OG/RD) for a short to ground. TEST the system for normal operation. No GO to R2 . R2 CHECK THE BLOWER MOTOR SPEED CONTROL Blower Motor Speed Control C1308 EATC Module C228b * Does the blower motor operate? Yes INSTALL a new blower motor speed control. TEST the system for normal operation. No GO to R3 . R3 CHECK THE BLOWER MOTOR SPEED CONTROL CIRCUITS FOR AN OPEN Blower Motor Speed Control C1308 Measure the resistance between the blower motor speed control C1308: * pin 1, circuit 269 (LB/OG) and the EATC module C228b pin 10. * pin 2, circuit 752 (YE/RD) and the EATC module C228b pin 23. * pin 3, circuit 754 (LG/WH) and the EATC module C228b pin 24. * Are the resistances less than 5 ohms?… Read More

1995 Oldsmobile Cutlass Supreme DTC 77

Download Direct-Hit 1995 Oldsmobile Cutlass Supreme 3.1L Test Details Hotline Archive # 97688 Confirmed Fix Vehicle Application: 1993 Chevrolet Camaro 3.4L 1995 Chevrolet Camaro 3.4L, Vin S 1994 Buick Skylark Custom 3.1L, Vin M, Eng Cfg V6 1995 Chevrolet Lumina 3.1L 1994 Chevrolet Corsica 3.1L, Vin M, Eng Cfg V6 1995 Pontiac Grand AM SE 3.1L, Vin M, Eng Cfg V6 1994 Oldsmobile Cutlass Supreme S 3.1L, Vin M 1995 Pontiac Grand Prix SE 3.1L Customer Concern: DTC 77. Tests/Procedures: 1. Remove the throttle body, and inspect the Exhaust Gas Recirculation Valve (EGR) port in the intake plenum. 2. The passage plugs at the bottom where it dumps into the plenum. 3. Best to use an old speedometer cable in a drill to run inside the passage to knock all the carbon out. Potential Causes: Restricted Exhaust Gas Recirculation (EGR) Passages Tech Tips: When an EGR solenoid is activated by the Powertrain Control Module (PCM), the PCM monitors the change in the Manifold Absolute Pressure (MAP) reading.… Read More

2000 Chevrolet Blazer MANUAL A/C-HEATER SYSTEMS

Download 1. Disconnect the electrical connector (3). 2. Remove the blower motor resistor mounting screws (1). 3. Remove the blower motor resistor (2) from the blower case. Fig. 3: Identifying Blower Motor Resistor Assembly (C42) Courtesy of GENERAL MOTORS CORP. Installation Procedure (C42) 1. Install the blower motor resistor (2) to the blower case. 2. Install the blower motor resistor mounting screws (1). Tighten Tighten the screws to 1.9 N.m (17 lb in). 3. Connect the electrical connector (3). Removal Procedure (C60) 1. Remove the A/C control relay bracket with the relay. 2. Remove the blower resistor harness. 3. Remove the stud from the IP, if necessary. 4. Remove the blower motor resistor mounting screw. 5. Cut the access cover from the case. Cut all four sides of the cover in order to remove the three attaching screws. Use a sharp utility knife in order to cut the case. Make the cuts straight and clean.… Read More

1997 Buick Century COLD ENGINE TICK OR RATTLE AFTER START-UP

Download 1997 Buick Century Limited 3.1/3.4L ENG TICK OR RATTLE AFTER COLD START UP COLD ENGINE TICK OR RATTLE AFTER START-UP (REPLACE PISTON/PIN ASSEMBLY) Model(s): 1994-95 Buick Regal 1994-97 Buick Skylark 1994-98 Buick Century 1994-95 Chevrolet Beretta Corsica, Lumina, Monte Carlo 1996-98 Chevrolet Venture 1997-98 Chevrolet Malibu 1993-97 Oldsmobile Cutlass Supreme 1994-96 Oldsmobile Cutlass Ciera 1994-97 Oldsmobile Achieva 1996-98 Oldsmobile Silhouette 1997-98 Oldsmobile Cutlass 1994-98 Pontiac Grand Am, Grand Prix 1996-98 Pontiac Trans Sport with 3100, 3400 V6 Engine (VINs M, E – RPOs L82, LA1) CONDITION Some customers may comment on a ticking type noise that begins shortly after cold engine start-up and gradually diminishes as the engine warms up. In most cases, the noise is gone after five (5) minutes. In severe cases, the noise may not disappear when lhe engine is hot. CAUSE Under normal design tolerances when the piston pin bore is produced at the maximum tolerance and the piston pin is produced at the minimum tolerance (min-max tolerance) trace noise levels can occur.… Read More

2002 Ford Taurus WATER IN THE BLOWER CASE

Download FORD: 2001-2004 Taurus MERCURY: 2001-2004 Sable This article supersedes TSB 03-15-06 to update the vehicle model years and build date information. ISSUE Some vehicles built between 5/1/2001 and 12/15/2003 may exhibit water in the blower case or on the passenger side floor, an inoperative climate control blower motor , a motor that operates on high speed only, and/or a blower motor resistor failure. ACTION Inspect and seal cowl area and install Rain-Hat Extension Seal. Inspect and replace blower motor and/or blower motor resistor if there is evidence of water/corrosion. Refer to the following Service Procedure for details. SERVICE PROCEDURE 1. Access blower motor and resistor per the Workshop Manual Sections 412-02 and 412-04. Inspect for evidence of water/corrosion. If water/corrosion are found or parts have failed, replace per Workshop Manual (blower motor 1F1Z- 19805-AA and resistor F6DZ-19A706-AA). 2. Visually inspect the Cowl Vent Screen located under the RH windshield wiper to verify if the screen is fully seated.… Read More

Honda Immobilizer Emulator Manual Installation Instructions

Download
Honda immobilizer emulator you must install in the motor ECU. Remove motor ECU from the car and open it. Inside you will find small immobilizer board. Exist 2 modifications: 1. Honda cars year 1995-1998 (Civic, Accord and others). Inside immo board looks like in picture. On this board is small 44pins processor and OKI M851G EEPROM (you can read/write it like 93C46). Most common problem with this type immobilizer is IMMO-ECU synchronization lost (this happens when ignition are switched ON with red key ). To solve this problem just erase OKI M851G EEPROM to FF…FF. To disable immobilizer just remove immobilizer board (marked in red on photo) from motor ECU. Honda immo emulator is no needed for this kind of ECU. 2. Honda cars year 1999-2002 (Accord, CRV, Civic and other). ). Inside immo board looks like in picture. On this board is 28pins processor with label. To disable immobilizer remove immobilizer board marked in red from motor ECU and install immobilizer emulator in his place (one to one – emulator pin1 must be soldered in motor ECU immo connector pin1).… Read More

2005 Chevy Truck Silverado 1500 Blower Motor Resistor Replacement

Download 2005 Chevy Truck Silverado 1500 2WD V8-5.3L VIN T Vehicle Level Heating and Air Conditioning Blower Motor Resistor Service and Repair Blower Motor Resistor Replacement. BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor. 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.… Read More

2008-2009 Honda CBR 1000 RR Fireblade Manual Installation Instructions

Download
Preparation 1. Remove the rider’s seat and lower cowl. Please see pages 104-106 of the Owner’s Manual for details of removing the lower cowl. 2. Disconnect the exhaust valve servo motor located under the rider’s seat. First, unclip the wiring connector from the under tray by depressing the tab under the connector sliding it to the left. You can now separate the connector. 3. Remove the bolt securing the servo motor to the under tray. Pull the motor off its post and disconnect the cable. 4. Pull the cable through from below, replace the servo motor, reconnect the wiring and clip the connector back in to place. 5. Remove stock muffler by: a) loosen the slip joint to header clamp b) remove rear mounting bolt from rider’s footrest hanger c) detach the footrest hanger d) rotate the muffler to one side and pull it off the headers 6. Remove heat shield from the back of the footrest by taking off the small bolt at the front.… Read More

2002 Chrysler Voyager LX ACCESSORIES and EQUIPMENT Power Windows

Download TROUBLE SHOOTING Inspect power window circuit breaker (25-amp), located in left kick panel. Inspect fuse No. 28 (40-amp) in Intelligent Power Module (IPM). IPM is located on left side of engine compartment. Inspect ground at right “B” pillar. SYSTEM TESTS ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay.… Read More