". You can read and download the PDF file on this page, or you can watch the video tutorial. Please use another keyword if these document aren't what you look for.
2004 Tahoe LS 4WD Failed emissions. Codes indicate gas cap and evap leaks. Replaced gas cap with OEM. Purchased: ACDelco 214-2149 Professional Vapor Canister Purge.
An ACDelco Professional, premium aftermarket Vapor Canister Vent Solenoid is an emission control component and is the ideal high quality replacement for your GM.
where is the vapor canister purge solenoid located in a chevy s10 pick up 1996.
Filed Under (Hyundai) by Doe Namblas on 02-04-2014
Download 2002 Hyundai Accent 1.6L, Vin C 2003 Hyundai Accent GS 1.5L Customer Concern: Difficulty filling the gas tank. The pump keeps clicking off. Tests/Procedures: 1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at the fuel tank in case the vapor line is plugged/restricted.… Read More
Download 2001 Hyundai Accent Difficulty filling the gas tank. The pump keeps clicking off.
Filed Under (Other Manuals) by Doe Namblas on 15-01-2014
Download DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit) Models: 1999-2007 Chevrolet Silverado (Classic) Models 1999-2007 GMC Sierra (Classic) Models 2007-2009 Chevrolet Silverado Models (Excluding Hybrid) 2007-2009 GMC Sierra Models (Excluding Hybrid) This bulletin is being revised to provide an updated picture of the remote filter box and to add an important statement to not replace the EVAP canister. Please discard Corporate Bulletin Number 02-06-04-037E (Section 06 — Engine/Propulsion System). Condition Some customers whose vehicles are operated in dusty type environments, such as farming or mining off*road type applications, may comment about the illumination of the check engine light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set. Cause Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition. Correction (1999-2007 Classic/Old Style Models) After following the published SI diagnostics for P0446 and determining that the EVAP canister vent valve is the cause of the MIL light, replace the existing EVAP canister vent valve assembly with a new assembly.… Read More
Download Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 31-12-2013
Download Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages.… Read More
Download 2004 Chevrolet Chevy K Silverado Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup
Filed Under (Honda) by Doe Namblas on 31-12-2013
Download SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe.… Read More
Download 1984-1995 Honda Civic/CRX Positive Crankcase Ventilation (PCV) System
Filed Under (Acura) by Doe Namblas on 03-01-2014
Download Part # 307-05-0290 Racing Intake Manifold for • 1999-2000 Honda Civic Si • 1997-2001 Acura Integra Type-R • 1992-1993 Acura Integra GSR • 1994-1997 Honda Del Sol DOHC VTEC. Removal 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt manifold bracket from engine block and intake manifold. This bracket will not be used in assembly and installation. Remove intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors.… Read More
Download 1997-2001 Acura Integra Type-R Racing Intake Manifold
Filed Under (Other Manuals) by Doe Namblas on 01-01-2014
Download 1. Turn OFF the ignition. 2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 3. Disconnect the electrical connector. 4. Remove the EVAP vent valve bracket bolt. 5. Remove the EVAP vent valve from the bracket. 6. Disconnect the vent hose from the EVAP vent valve. 7. Remove the EVAP vent valve. Installation Procedure 1. Install the EVAP vent valve on bracket. 2. Connect the vent hose. Canister vent hose should be routed below the fuel tank fill and vent hoses. Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener.… Read More
Download Evaporative Emission (EVAP) Vent Valve Replacement
Filed Under (Peugeot) by Doe Namblas on 31-12-2013
Tools needed: 7mm hose clamp driver T30 screwdriver Phillips head screwdriver 4mm and 5mm allen key/allen socket 10mm socket.
1. Lift the bonnet and begin by undoing the two jubilee clips holding the hose between the airbox and turbo inlet. Pull off the breather to the cam cover and remove the whole hose assembly from the car. 2. Remove the airbox by undoing the single bolt on the left hand side, then pulling it upwards to remove it from the rubber grommets that hold it to the top of the inlet manifold, giving you access to the cold air feed that simply pulls off the right hand side. 3. Remove the MAP sensor from the top of the inlet manifold as shown, then push it firmly into the supplied Forge MAP sensor boss. A little silicon spray will make it easier. Attach the length of silicon vacuum hose supplied to the vacuum nipple on the side of the boss, then reattach the whole assembly back to the inlet manifold with the brass screw provided.… Read More
Download PEUGEOT 207 GTI/ R56 MINI COOPER DUMP VALVE INSTALLATION
Filed Under (Acura) by Doe Namblas on 01-01-2014
Download 1. Relieve fuel pressure by loosening banjo bolt on top of fuel fi lter. Disconnect the fuel line at fuel rail. It is recommended that the washers be replaced. Next, disconnect the fuel injector harness holder and unbolt. Disconnect hoses from fuel pressure regulator (FPR). 2. Disconnect intake tubing/pipe from throttle body. Next, disconnect all hoses leading to intake manifold and throttle body, including throttle cable bracket on manifold. On throttle body, disconnect throttle positions sensor (TPS) and map sensor. 3. Unbolt (2) lower intake manifold bolts that secure the manifold to the engine block. This bracket will still be used to accommodate the heater bypass pipe. Next, unbolt the manifold from the cylinder head. Remove the intake manifold, throttle body, and fuel rail as one unit. Inspect intake manifold gasket. Replace as needed. Make sure to note all disconnect hoses and sensors. 4. Remove the intake air bypass (IAB) vacuum tank, check valve, and control solenoid valve.… Read More
Download 1994-2001 Acura Integra Racing Intake Manifold
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 19-12-2013
Download Malfunction Indicator Lamp (MIL) On, Transmission Stuck in Second or Third Gear, Instrument Cluster Inoperative (Verify and Repair Source of Voltage Loss In Transmission Solenoid Power Supply Circuit ) Models: 2006 and Prior GM Passenger Cars and Light Duty Trucks 2005-2006 HUMMER H2 2006 HUMMER H3 2005-2006 Saab 9-7X with 4L60-E, 4L65-E, 4L80-E or 4L85-E Automatic Transmission (RPOs M30, M32, M33, MT1, MN8) Condition Some customers may comment on one or more of the following conditions: Upon investigation, one or all of the diagnostic trouble codes (DTCs) P0740, P0753, P0758, P0785, P0787, P0973, P0976, P1860, P2761, P2764 and P2769 may be set depending on the vehicle. Cause The most likely cause of this condition may be a loss of voltage to the transmission solenoid power supply circuit. This condition may also be the result of an incorrect installation of an aftermarket electronic device such as a remote starter or alarm system.… Read More
Download 2001 Chevrolet Chevy K Silverado Transmission Stuck in Second or Third Gear
Filed Under (Infiniti) by Doe Namblas on 16-12-2013
Download Vehicle Application: 2001 Infiniti QX4 3.5L, USA/Canada 2002 Nissan Pathfinder 3.5L, USA/Canada 2001 Nissan Pathfinder 3.5L, USA/Canada2003 Infiniti QX4 3.5L, USA/Canada Customer Concern: The check engine light is on with a trouble code P1140. Tests/Procedures: 1. Check the right side (passenger side) Intake Valve Timing Control Position (IVTCP) sensor for 12 volts on the Black/White wire. 2. Check the IVTCP sensor for a good ground on the Black wire. 3. Scope the Yellow/Green signal wire and look for a square wave signal of around 8 volts. Check the pattern of the right side sensor and if unsure of the pattern, compare it to the left bank sensor. Potential Causes: IVTCP Sensor Wiring — IVTCP sensor wiring/connection. Tech Tips: This code is for the right (passenger) bank IVTCP Sensor or sensor circuit. The right and left bank sensors can be swapped from side to side to see if the code will follow the sensor.… Read More
Download 2001 Infiniti QX4 Direct-Hit – Hotline Archive Detail