2000 Ford F-150 Rear Drive Axle/Differential

Download 1. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the RH kick panel area. Failure to do so can result in unexpected inflation or deflation of the air springs, which can result in shifting of the vehicle during these operations. Raise and support the vehicle. 2. Remove the wheel and tire assembly. 3. Remove the differential housing cover (4033). ? Drain the lubricant. For additional information, refer to Differential Housing Cover in this section. 4. Remove the brake calipers and discs. 5. Remove the differential pinion shaft (4211). 1. Remove and discard the differential pinion shaft lock bolt. 2. Remove the differential pinion shaft. 6. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers (4N237). 1.… Read More

TOYOTA RAV4 STEERING INTERMEDIATE SHAFT NOISE

Download 1. Install a steering wheel holder. NOTE: Ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft by installing a steering wheel holder. 2. Remove the column hole cover silencer sheet. Turn back the floor carpet, remove the 2 clips, and remove the column hole cover silencer sheet. A. Place matchmarks (“a”) on the No. 2 steering intermediate shaft and steering column. B. Remove bolt A and detach the No. 2 steering assembly from the steering gear. C. Remove bolt B and detach the No. 2 steering intermediate shaft from the steering column. 4. Remove the No. 1 steering column hole cover sub-assembly by removing the clamp and disconnecting the column hole cover from the steering gear. 5. Remove the intermediate shaft. Remove the bolt and disconnect the steering intermediate shaft from the steering gear. 6. Install the NEW intermediate shaft onto the steering gear.… Read More

2007 Honda Accord CR-V and Civic Remote Engine Starter FAQ

Download
Model Information Release date for Accord Remote Starter System: September 20, 2007 Release date for CR-V and Civic Remote Starter System: End of September 2007 Technical Questions Q: What does the Honda Remote Engine Starter System do? A: The Honda Remote Engine Starter is a two-way remote system that starts and stops your vehicle’s engine anywhere within a 200-foot range. It’s designed to warm up your vehicle in the winter and cool it down in the summer. Q: How much is the Honda Remote Engine Starter? A: Approximately $499.00 without installation for all applicable Honda models. Check with your Honda dealer for the installation cost. Q: Can I install it myself? A: AHM does not recommend that customers install the Honda Remote Engine Starter due to the complexity of its electrical components. Authorized Honda Technicians are professionally trained to safely install the Remote Engine Starter. Q: Can I have my neighborhood audio shop install the Honda Remote Engine Starter?… Read More

2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module

Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

2000 Honda Accord EX Coupe Repair Instructions

Download Applies To: 1998-00 Accord L4 – See VEHICLES AFFECTED MIL Comes On With DTCs P0171 and/or P0172 (Supersedes 00-018, dated March 14, 2000) SYMPTOM The MIL (Malfunction Indicator Lamp) comes on with DTCs P0171 (Fuel System Too Lean) and/or P0172 (Fuel System Too Rich) stored in the ECM/PCM . PROBABLE CAUSE Moisture in the fuel pressure regulator. VEHICLES AFFECTED 1998-99 2-door: ALL 1998-99 4-door: ALL 2000 2-door:From VIN 1HGCG3. . .YA000001 thru YA000919 2000 4-door:From VIN 1HGCG6. . .YA000001 thru YA002332 From VIN 1HGCG5. . .YA000001 thru YA012613 From VIN JHMCG5. . .YC000001 thru YC000015 VIN JHMCG6. . .YC000001 CORRECTIVE ACTION Replace the fuel pressure regulator, and reroute the fuel pressure regulator vacuum line. PARTS INFORMATION Fuel Pressure Regulator (All):P/N 16740-PAA-A01, H/C 5429048 Fuel Pressure Regulator Tube Kit A (M/T with cruise control):P/N 06168-PAA-A10, H/C 6383186 Fuel Pressure Regulator Tube Kit B (A/T with cruise control):P/N 06168-PAA-A60, H/C 6383160 Fuel Pressure Regulator Tube Kit C (M/T without cruise control):P/N 06168-PAB- A00, H/C 6383194 Fuel Pressure Regulator Tube Kit D (A/T without cruise control):P/N 06168-PAB- A50, H/C 6383178 REPAIR PROCEDURE 1.… Read More

556H Honda / Acura Immobilizer Bypass Module Installation Instruction

Download Mode 1 Mode 2 ? Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 2002-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

Outlaw Clutch Spring Kit Installation Instructions For Honda ATV’s

Download
Models: 350 Rancher TRX 350 TM/TE/FM/FE 00-02 Kit Part # HLCKH350RN 400 Fourman TRX 400 95-03 Kit Part # HLCKH450FM-P 450 Fourman S/ES TRX FE/FM 98-03 Kit Part # HLCKH450FM-P 500 Rubicon TRX 500 FA 01-03 Kit Part # HLCKH500RC ATV’s can be dangerous. High Lifter has no control over the use of any part. High Lifter expects the customer to exercise good judgment as to the proper selection, installation, use and maintenance of any part. Neither High Lifter Products or EPI accepts any responsibility for damage to property including OEM parts or personal injury because of misuse, improper installation and improper application of any parts in any way by any person. Contact your local dealer to schedule installation of this clutch kit if you are not a qualified ATV mechanic. Tools needed to install clutch kit: Set of metric sockets 27mm socket Phillips and flat tip screwdrivers Torque wrench Spring tool or needle nose pliers (45 or 90 degree bent pliers work well) ½” impact wrench 5mm allen wrench Honda motor oil or equivalent Honda 500 clutch tool 07ZMC-HN2A100 REQUIRED for Rubicon only Honda Clutch tool #07933-HB300A or EPI #PCP-11 (An alternative to these tools would be a gear puller see photo at end of instructions) Gasket for Honda 400/450 provided in kit.… Read More

1991 Infiniti G20 AXLE SHAFTS FRONT

Download 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts. REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose.… Read More

FORD LIMITED SLIP DIFFERENTIAL INSTALLATION INSTRUCTIONS

Download -IMPORTANT LUBRICANT NOTE- The Auburn Gear limited-slip differential design has been extensively tested with high quality non-synthetic 80W90 hypoid oils treated with GM or Ford friction additives (3 oz. of additive will treat 1 quart of oil). To avoid differential clutch chatter (noise) and for optimum performance, use the oil and additive described above. Use of other additive and oil types may cause differential clutch chatter. Ford Part Number: C8A219B546A GM Part Number: 1052358 PINION SHAFT MODIFICATION Certain “C” clip axle applications with high gear ratios will require pinion shaft modification due to the thickness of the ring gear. The thick ring gear will prohibit the pinion shaft from being removed making “C” clip installation impossible. Use the following procedure to modify the pinion shaft. 1. Modification to be 90º to the pinion shaft lock screw hole as shown. It is recommended that this be accomplished through grinding. 2. Remove sharp edge from modified section by buffing.… Read More

Honda / Acura SIRIUS Interface HON-SC1 INSTALLATION INSTRUCTIONS

Download Compatibility The HON-SC1 is designed to be compatible with select Honda/Acura vehicles. Please consult table for compatibility listing. Compatible Headunit Types: • CD only Headunits* • CD + Cassette Headunits* • 6-CD changer Headunits* • Touch Screen Monitor Headunits • Non-Touch Screen Monitor Headunits * Note: Radio must have a “SAT” or “XM” button to access SIRIUS audio modes. In addition, the HON-SC1 is compatible with most additional factory audio accessories that might be included, such as: • Rear Seat Audio Control Center • Rear Seat Entertainment (DVD/Monitor) System • Heads up display (HUD) • Steering wheel controls Note: Kit not recommended for vehicles with Technology Package (Please see Acura’s website for details). The HON-SC1 is not compatible with the factory satellite radio antenna that might be installed in the vehicle. For best operation you must install a SIRIUS compatible antenna as supplied with the compatible SIRIUS Satellite Radio tuner.… Read More