2004-2006 Ford Double DIN Installation Kit PART 95-5812 INSTALLATION INSTRUCTIONS

Download FORD Edge 2007-2009 / Expedition 2007-2009 Explorer 2006-2009 / Explorer Sport Trac 2006-2009 F-150 2004-2008 / F Series 2005-2008 Five-Hundred 2005-2007 / Focus 2005-2007 / FreeStar 2004-2007 Freestyle 2005-2007 / Fusion 2006-2009 Mustang 2005-2009 / Super Duty 2008-2009 Taurus 2008-2009 / Taurus X 2008-2009 MERCURY Monterey 2004-2007 / Milan 2006-2008 Montego 2005-2007 / Mountaineer 2006-2009 Sable 2008-2009 LINCOLN Mark LT 2005-2009 Factory Navigation Only: MKX 2007-2009 / Navigator 2007-2009. DASH DISASSEMBLY A B C D E FORD MUSTANG 2005-2009 Remove the small rectangular shifter lever trim panel if equipped . (Figure A) 2 Remove (4) 9/32″screws from the radio to remove. (Figure E) 7 Remove (2) Phillips screws from under the center armrest at the back of the shifter trim panel (includingcup holders). (Figure B) 3 Unclip and remove panel. (Figure B) 4 Unclip and remove the (2) center stack trim panels from the left and right side of the radio and climate controls.… Read More

2001 Ford Windstar COWL TOP VENT PANEL Installation Instructions

Download 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top vent panel. 2. To install, reverse removal procedure. Tighten bolts and nuts to specification. See TORQUE SPECIFICATIONS . INTAKE MANIFOLD Removal 1. Remove cowl top vent panel. See COWL TOP VENT PANEL . Release fuel pressure and disconnect fuel lines. See FUEL PRESSURE RELEASE & FUEL LINE CONNECTIONS . 2. Disconnect negative battery cable. Drain cooling system. Remove air cleaner assembly and heat tube. Disconnect control cables and linkage at throttle body. Disconnect accelerator cable bracket, and secure aside. 3. Disconnect necessary linkages at intake manifold. Disconnect wiring harness connectors, vacuum hoses, coolant hoses and PCV hoses as necessary. Remove heater tube with fuel lines attached. 4. Remove A/C compressor support bracket (if equipped). Remove throttle body and EGR valve assembly. Note location of upper intake manifold bolts and studs.… Read More

2006 Honda Ridgeline Windshield Manual Installation Instructions

Vehicle type: Four-door crew-cab pickup NAGS®numbers*: Windshield part numbers FW2538 solar, electro-chromatic mirror, with sunroof, heated wiper-park area; FW2537 solar, with sunroof, heated wiper-park area; FW2536 solar, electro-chromatic mirror, heated wiper-park area; and FW2535 solar, heated-wiper park area; front door glass FD22564-65 F R/L solar; rear door glass FD22566-67 R R/L solar; and back glass FB22675 center slider solar and FB22568 slider
A. Windshield
Preparation 1. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. Note: Always wear eye and hand protection when working with glass. Make sure that you have the right glass and moldings, and that the urethane systems you are about to use are current. Windshield part numbers are FW2538, FW2537, FW2536 and FW2535. 2. Pull the rearview mirror in a downward fashion off the mirror pad. 3. Release the two retainers on the inside of the glove box and pivot the box to expose the wiper-park heater connector.… Read More


Download Ford : 2000-2007 Taurus 2000-2003 Windstar 2004-2007 Freestar MERCURY: 2000-2005 Sable 2004-2007 Monterey. ISSUE: Some 2000-2007 Taurus, 2000-2005 Sable, 2000-2003 Windstar, and 2004-2007 Freestar/Monterey vehicles, equipped with a 4F50N, AX4N, or AX4S transaxle, may exhibit an erratic fluid level reading on the transaxle dipstick and possible leaks around the filler tube and grommet. The condition may be due to a restricted transaxle vent. ACTION: Repair the transaxle vent restriction by replacing the transaxle vent with a 90° vent stem, small hose clamp, two (2) tie raps, and 24″ (61 cm) of 5/16″ (8 mm) vacuum hose. The 5/16″ (8 mm) vacuum hose will be routed from the 90° vent on the transaxle back to the cowl area, next to the brake master cylinder and tie rapped in place with the end of the hose facing down. Refer to the following Service Procedures. SERVICE PROCEDURE 1. Disconnect the mass air flow (MAF) sensor electrical connector.… Read More


DOWNLOAD APPLICATIONS FORD Edge 2007-2010 / Expedition 2007-2010 Explorer 2006-2010 / Explorer Sport Trac 2006-2010 F-150 2004-2008 / E Series 2009-10 / F Series 2005-2009 Five-Hundred 2005-2007 / Focus 2005-2007 / FreeStar 2004-2007 Freestyle 2005-2007 / Fusion 2006-2011 Mustang 2005-2009 / Super Duty 2008-2011 Taurus 2008 / Taurus X 2008-2009 MERCURY Monterey 2004-2007 / Milan 2006-2008 Montego 2005-2007 / Mountaineer 2006-2010 Sable 2008-2009 LINCOLN Mark LT 2005-2008. WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • 70-5520 – Ford Harness 2003-up • 70-5521 – Ford Amplified Harness 2003-up • 70-5522 – Ford Sub Harness 2003-up • XSVI-5520 NAV – Ford Interface 2006-up Antenna Adapter: • 40-CR10 – Chrysler/GM Antenna Adapter 2002-up. DASH DISASSEMBLY FORD F-150 2004-2008 LINCOLN MARK LT 2005-2008 FORD EXPEDITION 2007-2010 FORD EDGE 2007-2010. 1 Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap and remove entire panel surrounding the radio and climate controls. (Figure A) Remove (4) 9/32″ screws to remove the factory radio.… Read More


Please note that installing this undertail it’s not too difficult, but timeconsuming. The worst part is cutting the plastic oem mud flap because of it’s odd geometric shape and thickness variances. BEFORE INSTALLING THE UNDERTAIL PLEASE REMOVE THE FOLLOWING: – seat and unbolt seat cowl (10 bolts -4 in grab bar, 2 top side at back edge below the seat, 1 on each side/low section of cowl, and two plastic snap screws bottom side). -brake light sockets -cowl (very carefully not stressing or twisting it too much) -metal retainer for seat lock, slides upward (located on inside of trunk section) and mounting bracket. -lock cylinder. 2-Then, unbolt turn signals under mud flap 3-Cut turn signal wires close to the turn signal 4-Unscrew brake light lens (4 screws) 5-Put back oem seat cowl and draw a line using the edge of masking tape) at the bottom edge of the oem cowl for where you’ll need to cut the mud flap for undertailclearance.… Read More

2008 Buick Enclave Windshield Installation Instructions

Download 1. Always wear eye and hand protection when working with glass. Make sure you have the right glass and moldings and the urethane systems you are about to use are current. Windshield part numbers are DW1681 and DW1714. 2. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. 3. Drape a fender cover over the fender and tape up any vulnerable areas on the vehicle to protect against damage. Tape up the defroster vents to prevent debris from falling into the openings. 4. To remove the rearview mirror, loosen the 20T Torx set screw at the base and slide the mirror off the pad. 5. Remove the windshield-wiper nut covers. 6. Remove the windshield-wiper nuts using a 15-millimeter wrench or socket. Move the wiper arm in an up-and-down motion to break it loose from the post, or use a wiper puller.… Read More

Jaguar Enthusiasts IMT O-Ring replacement

Download Optional tools: 8mm wrench, can of carb cleaner, awl (small pointy instrument), nail set, shop vac Time: 2 hours This procedure was done on a 2005 3.0 First start off start with removing wiper arms: Disconnect wiper washer supply lines, being very carefull not to snap off nipples! Remove wiper arm 13mm (socket) nut covers, loosen nuts to top of stud. Grab ahold of wiper arm closest to nut as possible, with small hammer (arm assembly should “pop” on third hit). DO NOT remove nut then strike stud this will lead to everything else is down hill. If not have someone else do the replacement. Using “optional” nail set, push down on center push/pull pin on front cowl (8 pieces). Using flat screw driver (To reinstall these, push the pin from the underside up so it protrudes the top of its washer). Remove (7) rear cowl T20 screw covers and screws.… Read More


Download All instructions are written from the driver’s seat position looking forward at the vehicle dash. We advise caution whenever you are removing or handling plastic parts of a vehicle’s dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break. Start by applying the parking brake and place the transmission into the low position. Remove the ashtray and set it aside. Remove the Phillips screw located inside the open ashtray cavity. Insert the Dash Trim Tool in behind the upper-right corner of the bezel and carefully pull back to release the top- right clip of the bezel. Continue working the remaining clips loose with the Dash Trim Tool. Note: The climate control is attached to the trim bezel. Remove the two (2) plug wires attached to the climate control. Set the bezel aside. Place the Custom Bezel Mount just below the radio on the right side of the cavity.… Read More