2005 Chevy Truck Silverado 1500 Blower Motor Resistor Replacement

Download 2005 Chevy Truck Silverado 1500 2WD V8-5.3L VIN T Vehicle Level Heating and Air Conditioning Blower Motor Resistor Service and Repair Blower Motor Resistor Replacement. BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor. 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.… Read More

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

1993-1997 Peugeot 306 Timing belt replacement intervals

Download Apart from the visible condition of the belt, which is explained fully in the General Instructions/Toothed Timing Belts section, there are several other factors which must be considered when checking a timing belt: Is the belt an original or a replacement. 1. When was the belt last replaced and was it at the correct mileage. 2. Is the service history of the vehicle known. 3. Has the vehicle been operated under arduous conditions which might warrant a shorter replacement interval. 4. Is the general condition of other components in the camshaft drive, such as the tensioner, pulleys, and other ancillary components driven by the timing belt, typically the water pump, sound enough to ensure that the life of the replacement belt will not be affected. 5. If the condition of the existing belt appears good, can you be satisfied that the belt will not fail before the next check or service is due.… Read More

2000 Chevrolet Blazer MANUAL A/C-HEATER SYSTEMS

Download 1. Disconnect the electrical connector (3). 2. Remove the blower motor resistor mounting screws (1). 3. Remove the blower motor resistor (2) from the blower case. Fig. 3: Identifying Blower Motor Resistor Assembly (C42) Courtesy of GENERAL MOTORS CORP. Installation Procedure (C42) 1. Install the blower motor resistor (2) to the blower case. 2. Install the blower motor resistor mounting screws (1). Tighten Tighten the screws to 1.9 N.m (17 lb in). 3. Connect the electrical connector (3). Removal Procedure (C60) 1. Remove the A/C control relay bracket with the relay. 2. Remove the blower resistor harness. 3. Remove the stud from the IP, if necessary. 4. Remove the blower motor resistor mounting screw. 5. Cut the access cover from the case. Cut all four sides of the cover in order to remove the three attaching screws. Use a sharp utility knife in order to cut the case. Make the cuts straight and clean.… Read More

2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More

1997 F150 – Ford Expedition Radio Replacement Installation Instructions

Download Parts REQUIRED for the install Description Snap on in dash wire harness ** Please read instructions first Radio dash installation kit 1999 Ford F150/Expedition kit Optional parts for this install None. Remove Factory Radio STEP 1 : The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash.… Read More

1998 Chevrolet Blazer Engine Oil Cooler Hose/Pipe Replacement

Download 1998 Chevrolet Blazer – 4WD | Blazer, Bravada, Jimmy, S10 Pickup, ┬áSonoma (VIN S/T) Service Manual | Engine | Engine Mechanical – 4.3L | Repair Instructions. Engine Oil Cooler Hose/Pipe Replacement (4WD) Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6.… Read More

2000 Chevy Truck S10/T10 Transfer Case Replacement

Download 2000 Chevy Truck S10/T10 Blazer 4WD V6-4.3L VIN W Vehicle Level Transmission and Drivetrain Transfer Case Service and Repair NVG 233/243-NP1 Transfer Case Replacement. Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 7. Remove any wiring harness from the transfer case. 8. Support the transfer case with a transmission jack. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case. 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case.… Read More

1997-2002 FORD EXPEDITION 4WD 5″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

Download Before Starting Installation 1. Carefully read all warnings and instructions completely before beginning. 2. Verify all parts have been received in this kit by checking the parts list at the end of this document. 3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3175. 4. Special tools needed a. Torsion bar removal tool b. Brass drift c. 9/32″ & 1/2″ drill bit d. Tie Rod Puller 5. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Ride Height (For IFS w/ torsion bars) 1. Measure ride height with the vehicle supporting its own weight on level ground. To settle the suspension, the vehicle should be driven forward at least 10 feet immediately prior to taking these measurements.… Read More

1996-1999 Toyota Starlet Timing belt replacement intervals

Download Where possible the recommended intervals have been compiled from vehicle manufacturers’ information. In a few instances no recommendation has been made by the manufacturer and the decision to replace the belt must be made from the evidence of a thorough examination of the condition of the existing belt. Apart from the visible condition of the belt, which is explained fully in the General Instructions/Toothed Timing Belts section, there are several other factors which must be considered when checking a timing belt: Is the belt an original or a replacement. 1. When was the belt last replaced and was it at the correct mileage. 2. Is the service history of the vehicle known. 3. Has the vehicle been operated under arduous conditions which might warrant a shorter replacement interval. 4. Is the general condition of other components in the camshaft drive, such as the tensioner, pulleys, and other ancillary components driven by the timing belt, typically the water pump, sound enough to ensure that the life of the replacement belt will not be affected.… Read More