2009 Ford F150 Rear Bumper W1750 Installation Instructions

Download I. Overview Congratulations on your new purchase of the industries’ best and most stylish Rear Bumper available for the 2009 Ford F150! This Bumper has been engineered for strength while keeping the weight down. Your Rear Bumper designed in 3-D from digitized data, CNC laser cut, fabricated, and powder coated… all in the U.S.A. Enjoy the fit and finish of a quality Ford F150 Rear Bumper from Fab Fours Inc. II. Tools Required • Socket Wrench with Extension • Breaker Bar • 3/4″ & 18mm Sockets • Flat and Phillips Head Screw Drivers • 3/4″ Box End Wrench • T20 Torx Bit • Floor Jack and wood block. III. Removal of Stock Bumper A. Unplug the Factory License Plate lights from the back side of the light housing from underneath the truck. Turn counter clockwise until loose. Secure up and out of harm’s way. B. Disconnect the wiring harness from the back up sensors.… Read More

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

2006 Honda Civic SI Comptech Supercharger Kit Installation Instructions

Download STEP #1 Evacuate A/C system: • Have your local Air conditioning shop remove the HFC-134a refrigerant from your A/C system. They can reuse your coolant. After the supercharger installation you will need to return the car to them and have them refill and charge the system. This service should cost approximately $80.00. STEP #2 Remove ECM and ship to Hondata: • Remove the battery. • Remove ECM cover (A). • Remove bolts (D), then lift up the ECM. • Disconnect the ECM connectors A, B, and C. • Remove ECM and ship to Hondata (see Address to right.) STEP #3 Drain Coolant: • Jack up and support the front of the car on jack stands. • Make sure the engine is cool and remove the radiator cap. • Drain the cooling system by loosening the drain plug (A) at the bottom of the radiator. • Once all of the coolant is drained close the drain plug.… Read More

2000-2002 FORD FOCUS ZX3 AVENGER BODY KIT INSTALLATION INSTRUCTIONS

Download Cleaning procedure using a paper towel and grease remover or lacquer thinner, thoroughly clean area on car where the double face tape will come in contact with the painted surface. Do not allow thinner or cloth to remain on car too long as it can cause damage to the painted surface. Using either of the recommended adhesion promoters on a clean lint free cloth, apply a thin, uniform coating to the bonding surface, using the minimum amount that will fully coat the surface. Allow promoter to dry completely before attempting installation of the part. 1) front bumper replacement open the hood and remove the factory clips along the center of the factory front bumper. Remove one screw in each wheel well and also remove the two ten millimeter bolts located on the underside of the bumper. Remove the factory front bumper and discard the styrofoam absorber. Remove the grill from the factory bumper and place it on the new wings west front bumper.… Read More

2001-2003 Acura 3.2CL Supercharger Installation Instructions

Download Step #1 Disconnect Negative battery terminal Drain coolant from the radiator. Remove plastic engine covers. Disconnect Positive battery cable. Remove battery tie-down, battery & plastic battery tray. Remove stock air box lid, filter & air box bottom (A). Remove wiring harness from clip (B). Remove 6 mounting bolts (C), and remove the mounting bolt (D), then remove the tray base (E) and tray base bracket (F). Label & disconnect hoses from air inlet tube. Loosen clamp and remove tube. Step #2Lower Air box On most models: The lower airbox is accessable and removeable without removing the bumper . Remove the 4 screws holding the lower splash guard to the bumper and move splash guard enough to access the airbox mounting screws (G) Lower & remove stock air box Remove stock bracket in engine bay (E). Remove small rubber grommet in sub-frame next to battery (F). Bumper Removal: Remove (2) screws at top corner in wheel wells (C) , (4) snap clips along grill top (B), (4) snap clips underneath (D) & (2) screws at the back of bumper underneath near wheels.… Read More

Kit Number 57-0662 Installation Instructions

Download Citroen C4 1.6Hdi 2004-2009, Citroen Berlingo 1.6L 2005-2009, Citroen C2 1.6Hdi 2005-2009, Citroen C3 1.6Hdi 2008-2009, Citroen C3 Picasso 1.6Hdi 2009, Citroen C4 Picasso 1.6Hdi 2006-2009, Citroen C5 1.6Hdi 2005-2009, Mini Cooper 1.6Hdi 2007-2009, Mini Cooper Clubman 1.6Hdi 2007-2009, Peugeot 207 1.6 2006-2009, Peugeot 308 1.6 2007-2009, Peugeot 407 1.6 2005-2009, Peugeot Partner 1.6 2006-2009.
Parts list: 1 x Air filter Element. 1 x Silicone Intake Hose. 1 x Flexi Cold Air Hose. 1 x Metal Adaptor Hose. 1 x Literature Pack. Fixing Kit :- 3 x Plastic Tie. 3 x #44 Hose Clamp. 1 x Mounting Bracket. 1 x M6 Nylock Nut. 2 x M6 Flat Washer. 1 x Hex Head Bolt M6x20.
Instruction sheet A2054-768 1. Disconnect the negative terminal from the vehicle battery. 2. To the install induction kit it is necessary to remove the bulkhead trims: 3. Unclip & remove the side cover surrounding the washer bottle etc.… Read More

FORD FOCUS POWER WINDOW INSTALLATION INSTRUCTIONS

Download Tools & Materials Needed: 1. Utility Knife 2. Wire Crimper 3. Torx™ Wrenches 4. Hex Nut Drivers 5. Drill and Bits 6. Phillips Head Screw Driver 7. Crank Spring Removal Tool (Special Tool, available at most Auto Parts Stores) – or – 8. Flat Screw Drivers (2) 9. Add-A-Circuit ™ fuse adapter 10. Silicon Sealant (Clear or Black) Procedure: (Approximate time to complete installation: 3 – 4 hours) A. Removing the Door Panel Coverings 1. For ease of installation, do both sides at the same time. 2. Roll the windows to approximately 1/2 open, and so the crank handle is in the Down Position. With either the Crank Spring Removal Tool, or a flat Screwdriver, remove the spring, located in a slot on the back of the crank. 3. Remove the cover plate for the remote-control mirror, which is held in place by 3 spring clips. Remove by gently pulling the front corner of the cover out, and then slide the cover back.… Read More

FORD F150, F250, F350 BODY LIFT KIT INSTALLATION INSTRUCTIONS

Download 2″ Lift 1992-96 F150 822 1992-97 F250*, F350* 822 3″ Lift 1992-96 F150 823 1992-97 F250*, F350* 823 Intake air duct 1. Remove intake air duct from top of radiator and throttle body. Fan shroud 1. Remove two bolts securing fan shroud to top of radiator. Pull fan shroud up and out of clips that secure fan shroud to bottom of radiator. Smog canister 1. Remove two bolts securing smog canister to passenger side fender well. Move canister about 5″ toward engine. Drill two new holes and install canister with stock hardware. This will allow the hose to reach the canister after cab has been lifted. Steering shaft (under dash) 1. Strap steering wheel to prevent accidental move- ment. 2. Under the dash, remove bolt that secures steering shaft to “U”-joint. Slide steering shaft out of “U”-joint. Front bumper 1. Loosen four bolts securing front bumper to front bumper brackets.… Read More

2004 Acura TL GOLD EMBLEM INSTALLATION INSTRUCTIONS

Download Installing the Front “A” Emblem 1. Remove the two bolts that secure the left front bumper strake to the bottom of the front bumper and remove the bumper strake by sliding it sidewise. 2. Repeat step 1 to remove the right side bumper strake. 3. Remove the left side engine compartment cover (two pins and two tabs). 4. Remove the right side engine compartment cover (three pins and three tabs). 5. Open the engine hood. Remove the front bulkhead cover (three clips, two screw clips and two pins). 6. On each side fold down the front inner fender, and remove the front bumper (ten clips, two bolts and two self-tapping screws ). To prevent damage, set the bumper on a blanket during installation of the emblem. 7. Remove the center molding (five self-tapping screws). 8. Remove the two self-tapping screws that secure the existing “A” emblem and remove the emblem.… Read More

2006-2007 Buick Lucerne BX1512 Installation Instructions

Download Attachment Tabs: Due to the design of the removable tabs, the RangeFinderII and Ambassador tow bars can not be used. Adapters, except the BX8833 and BX88151, can not be used with this baseplate. Installation Instructions: 1. Remove four pushpins from the radiator cover and lift to remove. Do this to both sides of the vehicle. Set pushpins and radiator cover aside to be reinstalled later. 2. Remove three pushpins from the top of the fascia. Do this to both sides of the vehicle. Set pushpins aside to be reinstalled later. 3. Remove five pushpins just forward of the front tire, on the edge of fascia. Do this to both sides of the vehicle. Set pushpins aside to be reinstalled later. 4. Pull wheel well cover aside and remove two metric bolts from back side of fascia using the 10mm socket. Do this to both sides of the vehicle. Set bolts aside to be reinstalled later.… Read More