installing a canister vent solenoid in a 2003 silverado truck

You search Auto repair manual PDF about installing a canister vent solenoid in a 2003 silverado truck, search results will appear below. If search results do not exist, please search by others keyword.

Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit

Filed Under (Other Manuals) by admin on 15-01-2014

Download DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit) Models: 1999-2007 Chevrolet Silverado (Classic) Models 1999-2007 GMC Sierra (Classic) Models 2007-2009 Chevrolet Silverado Models (Excluding Hybrid) 2007-2009 GMC Sierra Models (Excluding Hybrid) This bulletin is being revised to provide an updated picture of the remote filter box and to add an important statement to not replace the EVAP canister. Please discard Corporate Bulletin Number 02-06-04-037E (Section 06 — Engine/Propulsion System). Condition Some customers whose vehicles are operated in dusty type environments, such as farming or mining off*road type applications, may comment about the illumination of the check engine light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set. Cause Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition. Correction (1999-2007 Classic/Old Style Models) After following the published SI diagnostics for P0446 and determining that the EVAP canister vent valve is the cause of the MIL light, replace the existing EVAP canister vent valve assembly with a new assembly.… Read More

2004 Chevrolet Chevy K Silverado Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages.… Read More

BEDLOCKER FORD EXPLORER SPORT TRAC INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 06-12-2013

Download TOOLS REQUIRED FOR ASSEMBLY: 7/16″ wrench or socket 3/8″ wrench or socket #2 Phillips screwdriver Tape measure. The Bedlocker is designed to carry rainwater from the cover into the canister and then out through the drains. Most truck models have standard OE drain holes or plastic/rubber access ports in the front of the truck bed. Check to make sure your truck has the OE drain holes so that drilling into the sheet metal is not required. If drilling is necessary, be sure to check the underside of the truck bed for the best location. The holes should be located near the side and as far forward as possible. Use a drill bit suitable for sheet metal (such as a taper drill or step drill). Drill drain tube clearance holes at 3/4″ (19mm). This will need to be done before installing the cover. STEP 1: REMOVE CONTENTS & PLYWOOD PACKAGING Remove the canister and top cover from the box.… Read More

Evaporative Emission (EVAP) Vent Valve Replacement

Filed Under (Other Manuals) by admin on 01-01-2014

Download 1. Turn OFF the ignition. 2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 3. Disconnect the electrical connector. 4. Remove the EVAP vent valve bracket bolt. 5. Remove the EVAP vent valve from the bracket. 6. Disconnect the vent hose from the EVAP vent valve. 7. Remove the EVAP vent valve. Installation Procedure 1. Install the EVAP vent valve on bracket. 2. Connect the vent hose. Canister vent hose should be routed below the fuel tank fill and vent hoses. Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener.… Read More

2003 Cadillac Escalade Code C0660 will reset.

Filed Under (Cadillac) by admin on 20-12-2013

Download Vehicle Application: 2003 Cadillac Escalade 5.3L, Vin T, USA/Canada 2005 Chevrolet Suburban 1500 LS 5.3L, GAS, Vin T 2003 Cadillac Escalade EXT 6.0L 2005 GMC Yukon XL 1500 Slt 5.3L, FLEX, Vin Z 2005 Chevrolet Suburban 1500 LS 5.3L, FLEX, Vin Z Customer Concern: Code C0660 will reset. Tests/Procedures: 1. Check the RTD fuse located in the underhood fuse block. 2. Check for Battery Voltage (B+) on the Orange wire at the automatic level control air compressor pin F. 3. If less than B+ at pin F, check for a wiring and connection problem between the air compressor and the underhood fuse block. 4. Disconnect the compressor leveling module connector and check the resistance from the positive battery voltage circuit of the exhaust solenoid valve and the control circuit of the exhaust solenoid valve. Should be 30-90 ohms. 5. Check for B+ on the Dark Blue wire pin B at the air compressor with the exhaust solenoid commanded off.… Read More

FORD FLARESIDE INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 23-01-2014

Download TOOLS REQUIRED FOR ASSEMBLY: 7/16″ wrench or socket 3/8″ wrench or socket #2 Phillips screwdriver Tape measure STEP 1: REMOVE CONTENTS & PLYWOOD PACKAGING Remove the canister and top cover from the box. Remove components from inside the canister. Perform a quick inventory to insure all parts are there. Using the wrench or socket remove the 2 bolts holding the plywood packaging supports on the ends of the canister. Discard plywood packaging supports and bolts. Locate the rail guide bolts in the hardware pack and install them in the two holes where the packaging bolts and plywood were just removed. Repeat on both ends of the canister. TOOLS REQUIRED FOR ASSEMBLY: BEFORE YOU START: HARDWARE USED: STEP 2: INSTALL WIRING HARNESS You will need one or two support pieces (We suggest using the top of the box the Bedlocker was shipped in) to set in the truck bed. Set the support piece approximately one foot from the cab.… Read More

2001 Hyundai Accent Difficulty filling the gas tank. The pump keeps clicking off.

Filed Under (Hyundai) by admin on 02-04-2014

Download 2002 Hyundai Accent 1.6L, Vin C 2003 Hyundai Accent GS 1.5L Customer Concern: Difficulty filling the gas tank. The pump keeps clicking off. Tests/Procedures: 1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at the fuel tank in case the vapor line is plugged/restricted.… Read More

FORD FLARESIDE BEDLOCKER ELECTRIC RETRACTABLE TRUCK BED COVER INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 02-01-2014

Download
TOOLS REQUIRED FOR ASSEMBLY: 7/16″ wrench or socket 3/8″ wrench or socket #2 Phillips screwdriver Tape measure.
DRAIN HOLE LOCATIONS: The Bedlocker is designed to carry rainwater from the cover into the canister and then out through the drains. Most truck models have standard OE drain holes or plastic/rubber access ports in the front of the truck bed. Check to make sure your truck has the OE drain holes so that drilling into the sheet metal is not required. If drilling is necessary, be sure to check the underside of the truck bed for the best location. The holes should be located near the side and as far forward as possible. Use a drill bit suitable for sheet metal (such as a taper drill or step drill). Drill drain tube clearance holes at 3/4″ (19mm). This will need to be done before installing the cover.
OPTIONAL WIRING HARNESS FOR DASHBOARD SWITCH: The BedLocker also offers an optional wire harness (part # BL1120) to manually operate the tonneau cover from inside the cab of your truck.… Read More

2005 Dodge Truck Dakota TRANSMISSION SOLENOID/TRS

Filed Under (Dodge) by admin on 21-01-2014

Download The transmission solenoid/TRS assembly is internal to the transmission and mounted on the valve body assembly. The assembly consists of six solenoids that control hydraulic pressure to the six friction elements (transmission clutches), and the torque converter clutch. The pressure control solenoid is located on the side of the solenoid/TRS assembly. The solenoid/TRS assembly also contains five pressure switches that feed information to the TCM. OPERATION SOLENOIDS Solenoids are used to control the L/R, 2C, 4C, OD, and UD friction elements. The reverse clutch is controlled by line pressure and the position of the manual valve in the valve body. All the solenoids are contained within the Solenoid and Pressure Switch Assembly. The solenoid and pressure switch assembly contains one additional solenoid, Multi-Select (MS), which serves primarily to provide 2nd and 3rd gear limp-in operation. The solenoids receive electrical power from the Transmission Control Relay through a single wire. The TCM energizes or operates the solenoids individually by grounding the return wire of the solenoid as necessary.… Read More

2005-2007 NISSAN PATHFINDER MIL “ON” WITH DTC P0442/P0448/P0455/P0456/P1446

Filed Under (Nissan) by admin on 02-01-2014

Download IF YOU CONFIRM: A MIL “ON” with one or more of the following DTC(s) stored: • P0442 / P0448 / P0455 / P0456 / P1446 AND • EVAP Vent Control S/V is stuck open or will not seal when operated/closed. ACTIONS: 1. Replace the EVAP Vent Control S/V. 2. Install the Filter Kit (refer to the Service Procedure in this bulletin). 3. Clear any DTCs stored in the ECM. SERVICE PROCEDURE Replace Vent Control Valve 1. Replace the EVAP Vent Control S/V. • Refer to section EC in the Service Manual for replacement information. Install Filter Kit 1. Remove the spare tire. 2. Remove the EVAP canister mounting bolt (see Figure 1). • The canister will drop about 3 inches which will give you working room at the top. 3. Disconnect the vent hose (see Figure 1). 4. Reach above the EVAP canister and disconnect the vent hose at the vent control valve and remove the hose (see Figure 2).… Read More

You might also likeclose