2005 HONDA CR-V DOOR VISORS INSTALLATION INSTRUCTIONS

Download
PARTS LIST Left front door visor Right front door visor Left rear door visor Right rear door visor Installing the Front Door Visor 1. Lower the front door glass completely. Remove the door glass run channel from the door sash in the area shown. Do not remove the glass run channel from the door mirror base or the rear end of the door. AII 27171 TOOLS REQUIRED Isopropyl alcohol Shop towel Masking tape INSTALLATION NOTE: •These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors. Be careful not to damage the paint finish or glass run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours.… Read More

2000-UP FORD FOCUS 4 Door Sedan / Wagon, 3 Door Hatchback Audio Installation Instructions

Download Preliminary: disconnect the negative battery cable. Antenna: the factory antenna is located in the center front of vehicles roof. Radio removal and in-dash installation: note: the factory radio provision is a custom ford double din. When installing an aftermarket din stereo a dash kit is needed. We recommend the scosche fm1375 or fmc1370 installation kit. A set of din removal tools is also needed to remove the factory head unit. We recommend the scosche dt-1 ford din removal tools. 1. Insert ford din removal tools to release clips, pull out stereo, disconnect and remove. Front door speaker installation: note : the factory speaker provision is for a 6 x 8″ speaker. When installing an aftermarket 5 ¼ or 6 ½ speaker, a speaker adapter is required. We recommend the scosche sa68. 1. Extract (7) t-15 torx screws from the perimeter of door panel. 2. Remove screw cover from door opener cup, and extract (1) # 2 philips head screw from behind.… Read More

1999 Chrysler Truck Blend Door Actuator Replacement

Download 1999 Chrysler Truck Town & Country LWB FWD V6-3.8L VIN L Vehicle Level Heating and Air Conditioning Air Door Air Door Actuator / Motor Service and Repair Blend Door Actuator Replacement. REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes.… Read More

1997-1999 Buick Century/Regal 99-2001 AW-200GM INSTALLATION INSTRUCTIONS

Download BUICK Century 1997-99 LeSabre 1995-99 1 Park Avenue 1995-99 Regal 1995-99 Riviera 1996-99 Roadmaster 1995-96 Skylark 1996-98 CHEVROLET Impala 2000 Venture 2000 OLDSMOBILE Achieva 1996-98 Aurora 1995-99 Bravada 1998-99 Cutlass 1998-99 Cutlass Supreme 1995-97 Eighty-Eight 1994-99 Intrigue 1998-99 LSS 1996-99 Ninety-Eight 1994-96 Regency 1997-98 Silhouette 2000 PONTIAC Montana 2000 Sunfire 2000. BUICK LeSabre / Park Avenue 1995-99 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the plastic trim piece to the left of the glove box and (1) Phillips screw exposed. Unsnap the top edge of the knee bolster panel. Remove (1) Phillips screw from the panel. Remove the ashtray cluster and (2) Phillips screws from each side. Unclip the entire dash trim bezel and remove. Remove (3) 9/32″ hex-head screws securing the factory head unit and disconnect the wiring. Skip to the Installation Instructions for ALL VEHICLES on Page #6. CHEVROLET Impala 2000 Disconnect the negative battery terminal to prevent an accidental short circuit.… Read More

2009 Honda Civic 4-Doors Accessories Door Visors Installation Manual

Download
TOOLS AND SUPPLIES REQUIRED Isopropyl alcohol Shop towel Masking tape 6 in. Scale
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” NOTE: •Visors may not be legal in all states. Please check the laws of your state. •Be careful not to damage the paint finish and glass run channels when installing the door visors. •Handle the door visors with care. They are not designed to absorb shock or impact. •This door visor kit should only be installed if the ambient air temperature is 60°F (15°C) or above. •To allow the adhesive to cure, do not wash the vehicle for 24 hours. Installing the Rear Door Visor 1. Fully open the left rear door window. 2. Install one bracket (C) and one bracket (D) on the door sash at the measurements shown.… Read More

Ford Focus PRO-FIT Linear Fuel Doors Installation Instructions

Download Tools you will need: ? Ratchet set ? Flathead screwdriver ? Drill and drill bits (for electric locking fuel door only) ? Small file ? Degreaser ? Clear Rags Parts list (items not to scale):1) Fuel door with pull cable attached (pull cable is on electric locking fuel door only) 2) Wiring harnesses (long and short) with actuator (electric locking fuel door only) 3) L-bracket (x 4) 4) Washer (x 4) 5) Nylock nut (x 4) 6) Long hex bolt (x 4) 7) Short hex bolt (x 6) 8) Fuse taps (3 sizes – electric locking fuel door only) 9) Fuse (electric locking fuel door only) 10) Switch (electric locking fuel door only) 11) Sticky pads (electric locking fuel door only) 12) Tie wraps (electric locking fuel door only) 13) Gas cap 14) Wrenches 15) Black strip caulk (not pictured) PRO-FIT Linear Fuel Doors Ford Focus – Installation Instructions Prep WARNING: Do not perform this install near a flame source due to the risk of fire or explosion from gas fumes.… Read More

1997 BUICK REGAL RADIO REMOVAL AND IN-DASH INSTALLATION

Download Note: the factory radio provision is for a gm oversize radio chassis. An installation kit is recommended for aftermarket installations. We recommend the use of a scosche gm1580 kit for normal installations of din or shaft radios, or gm1590 kit for custom installations of japanese double din iso or 2 stacked din iso radios. 1. Unsnap gear selector trim bezel, unplug and remove the bezel. Extract (2) 10 mm bolts from metal console bracket. 2. Open armrest storage, lift up rubber mat and extract (2) 10 mm bolts from underneath. 3. Extract (2) 10 mm bolts from the front sides of the console, concealed up under the dash. 4. Slide shifter back into low gear, push down on spring- loaded shifter trim and pull complete center console to rear of the vehicle, allowing the center lower dash section (attached) to unsnap from the dash. 5. Extract (1) screw from bottom lower dash panel at right of glove box.… Read More

FORD FOCUS POWER WINDOW INSTALLATION INSTRUCTIONS

Download Tools & Materials Needed: 1. Utility Knife 2. Wire Crimper 3. Torx™ Wrenches 4. Hex Nut Drivers 5. Drill and Bits 6. Phillips Head Screw Driver 7. Crank Spring Removal Tool (Special Tool, available at most Auto Parts Stores) – or – 8. Flat Screw Drivers (2) 9. Add-A-Circuit ™ fuse adapter 10. Silicon Sealant (Clear or Black) Procedure: (Approximate time to complete installation: 3 – 4 hours) A. Removing the Door Panel Coverings 1. For ease of installation, do both sides at the same time. 2. Roll the windows to approximately 1/2 open, and so the crank handle is in the Down Position. With either the Crank Spring Removal Tool, or a flat Screwdriver, remove the spring, located in a slot on the back of the crank. 3. Remove the cover plate for the remote-control mirror, which is held in place by 3 spring clips. Remove by gently pulling the front corner of the cover out, and then slide the cover back.… Read More

2001-2005 HONDA CIVIC Vertical Doors Kit Installation Instructions

Download TOOLS REQUIRED FOR INSTALLATION: æ Spacers æ Blue painters tape æ Locktite red æ Screw Drivers Fork and Phillips æ Cutters æ 7mm,10mm, 13mm socket and extension æ Air ratchet, grinder and cutter æ 1/4, and 3/16 Allen wrench. (Note: The pictures on the manual are for reference only they may not match your vehicle.) 1) Disconnect the battery. 2) Remove fender: Remove all Phillip’s screws from the wheel well. Remove (1) 12mm bolt to loosen the bumper. Once the 12mm bolt has been removed pull on the bumper and remove (2) 8mm bolts from behind the bumper. Remove (3) 8mm bolts form the top of the fender. Remove (2) 8mm bolts from the bottom of the fender by the door. Remove (1) 8mm bolt holding the fender. At this point you should be able to remove the fender. 3) Remove the door catch: Open the door and remove (1) 10mm bolt from the body and (2) 10mm from the door.… Read More

Honda Accord WINDOW ROLL-UP MODULE INSTALLATION INSTRUCTIONS

Download INSTALLATION: 1. Remove driver side door panel (04 Coupe instructions) a. Remove screw cover and 2 screws from inside door handle cup b. Remove two screws beneath armrest c. Remove side mirror trim piece on top corner of door panel by pulling out on it d. Gently remove door panel by first pulling out on it at the bottom and then lifting it over the window lip on top e. Disconnect all wire harnesses and mechanical cables from the door panel and place the door panel in safe place f. Remove speaker by inserting a flat head screwdriver in the slot on top and gently pulling out on it. With the top tap released gently lift up on the speaker to free the bottom tabs NOTE: If you break a leg or two off of the speaker it is easily fixed by using short self tapping screws to secure the speaker to the door g.… Read More