2002 Pontiac Grand Prix GT THERMOSTAT REPLACEMENT

Download 2002 Pontiac Grand Prix GT 2002 ENGINE Engine Cooling – Grand Prix THERMOSTAT REPLACEMENT (3.1 L) Tools Required J 38185 Hose Clamp Pliers Removal Procedure 1. Remove the air cleaner intake duct. Refer to AIR CLEANER INTAKE DUCT . 2. Partially drain the cooling system. Refer to Draining and Filling Cooling System . 3. Use the J 38185 in order reposition the hose clamp from the water outlet housing. 4. Remove the radiator inlet hose from the water outlet housing. 5. Remove the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) 6. Remove the water outlet housing bolts. 7. Remove the water outlet housing and gasket. 8. Remove the thermostat. 9. Clean the water outlet housing mating surfaces. Installation Procedure 1. Install the thermostat. 2. Install the water outlet gasket and the water outlet housing. 3. Install the water outlet housing bolts.… Read More

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

1997 Chevy Truck C Tahoe Interior Lighting Module Locations

Download 1997 Chevy Truck C Tahoe 2WD V8-5.7L VIN R View: Under Center Of Instrument Panel Zoom Sized for Print Interior Lamp Control Module, Remote Control Door Lock Receiver Manufacturer supplied 2 different possible locations. Look for 5 wire connector with wire colors: gray, white, orange, pink & black. #PIT3819: Location of Interior Lamp Control Module – keywords control dim dome electrical entry ground illumination inoperative keyless lens light remort resistor RKE short – (Dec 23, 2005) Subject: Location of Interior Lamp Control Module. Models: 1995-2000 Chevrolet C/K Trucks, Suburban and Tahoe 1995-2000 GMC Yukon and C/K Trucks Classic Body Style Only The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this P1. Condition/Concern When diagnosing a dome lamp concern on one of the vehicles listed above, you may be unable to locate the Interior Lamp Control Module that is called out in the Service Manual.… Read More

Ford 7.3L 1994-1998 Powerstroke Turbo Diesel Digital Propane Injection

Download Parts Included: 1 – Regulator Assembly 1 – Regulator Mounting Bracket 1 – Propane Lock-off Solenoid 1 – Fuel Pressure Switch 1 – 3-way Pressure Control Solenoid 1 – Propane Pressure Sensor with Fitting 1 – Boost Signal Hose 1 – Electronic Control Unit (ECU) 1 – Harness Assembly 1 – Monitor Cable 1 – Heater Hose 1 – Enable Switch 1 – Fault Light 1 – Vapor Hose 1 – Discharge Fitting, Elbow (Vapor to Intake) 2 – Fitting (Heater Hose to Vaporizer) 2 – Parts Bag 1 – MSD Pro Data+ CD, PN 9608. HARDWARE INSTALLATION VAPORIzER/REgULAtOR COmPONENt AssEmbLy 1. Install the Outlet Orifice. Verify assembly is inserted as shown in Figure 11 pg. 12. 2. Install Propane Pressure Sensor. 3. Install Fuel Pressure Switch and fuel lock-off solenoid. 4. Install the 90° coolant hose elbow fittings to the regulator’s coolant inlet/outlet ports. 5. Install the Liquid Propane Line Fitting and the mounting bracket.… Read More

FORD DIESEL ENGINES Hydronic5 Espar Heater System Installation, Troubleshooting, Repair Manual

Download
HYDRONIC 5 for FORD DIESELENGINES Heater Model 25 1920 05 Installs are for models 250/350 4 wheel drive & 4 wheel ABS 2 wheel drive & 4 wheel ABS. Heater Warnings to Installer •Correct installation of this heater is necessary to ensure safe and proper operation. Read and understand this manual before attempting to install the heater. Failure to follow all these instructions could cause serious or fatal injury Explosion Hazard •Heater must be turned off while re-fueling. •Do not install heater in enclosed areas where combustible fumes may be present. Fire Hazard •Install the exhaust system so it will maintain a minimum distance of 50mm(2″) from any flammable or heat sensitive material. •Ensure that the fuel system is intact and there are no leaks. Asphyxiation Hazard •Route the heater exhaust so that exhaust fumes cannot enter any passenger compartments. •If running exhaust components through an enclosed compartment, ensure that it is vented to the outside.… Read More

Honda Civic Si Acura RSX Icebox Cold Air Intake Manual Installation Instructions

Download
Parts List: 1- Icebox lid w/ screws 1- Icebox Bottom 1- Lower Air Horn 1- Filter Elbow 1- 6 mm x 35 mm screw 1- 6 mm nut 1- Plastic pin 1- High Flow Filter Element 1- Filter Oil 1—CARB EO# Decal (RSX).
Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan.… Read More

2002 – 2003 Honda Civic Si & Acura RSX Comptech Icebox Cold Air Intake Installation Instructions

Download Parts List: 1- Icebox lid w/ screws 1- Icebox Bottom 1- Lower Air Horn 1- Filter Elbow 1- 6 mm x 35 mm screw 1- 6 mm nut 1- Plastic pin 1- High Flow Filter Element 1- Filter Oil 1—CARB EO# Decal (RSX). Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan.… Read More

2002-2003 Acura RSX Icebox Cold Air Intake Installation Instructions

Download Honda Civic Si & Acura RSX Icebox Cold Air Intake Installation Instructions (2002-2003 Honda Civic Si) (2002-2003 Acura RSX—All) Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan. •Remove ground strap bracket on side of transmission (C). Relocate ground strap from transmission bracket to top of transmission (D). Step #2 Install Comptech Airbox •Install (3) stock rubber grommets* (E) through large holes on underside of mounting ears on Icebox (a small dab of filter oil may be used to ease this process).… Read More

2003-2004 Acura MDX Blue Heat Coolant Heater

Download – Improper installation or repair of Webasto heating and cooling systems can cause fire or the leakage of deadly carbon monoxide leading to serious injury or death. – Installation and repair of Webasto heating and cooling systems requires special Webasto training, technical information, special tools and special equipment. – NEVER attempt to install or repair Webasto heating or cooling system unless you have successfully completed the factory training course and have the technical skills, technical information, tools and equipment required to properly complete the necessary procedures. – ALWAYS carefully follow Webasto installation and repair instructions and heed all WARNINGS. – Webasto rejects any liability for problems and damage caused by the system being installed by untrained personnel. General References – Bare body parts, for example around drilled holes, must be treated with anti-corrosive coating. – Secure hoses, cables and wiring harnesses with cable ties and fit protective hoses around them at chafing points.… Read More

1998 Ford Ranger Workshop Manual

Download Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Engine Stand 014-00232 or equivalent 1. Relieve the fuel pressure. For additional information, refer to Section 310-00 . 2. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 . 3. Drain the engine cooling system. For additional information, refer to Section 303-03 . 4. Remove the hood (16612). 5. Remove the air cleaner outlet tube (9B659). For additional information, refer to Section 303-12 . 6. Remove the accelerator control splash shield (9E766). 7. Remove the upper radiator hose (8260). 8. Remove the lower radiator hose (8286). 9. Remove the two bolts and position the fan shroud (8146) on the fan blade (8600). 10. Remove the water pump pulley, fan and shroud; refer to Section 303-03 . 11. Disconnect the radiator overflow tube. 2. On vehicles equipped with automatic transmissions, disconnect the transmission cooler lines. 13. Disconnect the mass air flow sensor.… Read More