". You can read and download the PDF file on this page, or you can watch the video tutorial. Please use another keyword if these document aren't what you look for.
We offer high quality new, OEM, aftermarket hyundai santa fe ignition switch parts. Buy online or call toll free..
We offer high quality new, OEM, aftermarket hyundai accent ignition switch parts. Buy online or call toll free..
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2001-2002 Hyundai Accent..
Filed Under (Hyundai) by Doe Namblas on 02-04-2014
Download 2002 Hyundai Accent 1.6L, Vin C 2003 Hyundai Accent GS 1.5L Customer Concern: Difficulty filling the gas tank. The pump keeps clicking off. Tests/Procedures: 1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at the fuel tank in case the vapor line is plugged/restricted.… Read More
Download 2001 Hyundai Accent Difficulty filling the gas tank. The pump keeps clicking off.
Filed Under (Ford) by Doe Namblas on 01-01-2014
Download “Mobile-ease™” Hands Free System Connector Wiring Harness Required for Installation of “Mobile-ease™” Hands Free System 3W4Z-14A411-AA 2005-2007 Hands Free System Requires Connector Harness 14A411 for Installation3W4Z-19G399-AA2005-2007 “Street Appearance Package” ZX3/ZX5 Includes Front & Rear Bumper Fascia & Chromed Exhaust Tip, Primed 6S4Z-6120049-AA 2006-2007 ZX4 Includes Front & Rear Bumper Fascia & Chromed Exhaust Tip, Primed 6S4Z-5420049-BA 2006-2007 Bug Shield Styled Smoke-Color (Single-Pack) 5S4Z-16C900-A 2005-2007 Cargo Area Protector 3-Door/5-Door Black 1M5Z-6111600-AA 2001-2007 Sedan Black 1M5Z-5411600-DA 2001-2007 Wagon Black 1M5Z-7411600-CA 2001-2007 Cargo Logic System Without Logo Sedan, Heathered Black Ink (00) 3M5Z-5411600-AA 2003-2007 3-Door Hatchback, Heathered Black Ink (00) 3M5Z-6111600-AA 2003-2007 Wagon, Heathered Pebble (65) 3M5Z-7411600-AA 2003-2007 Wagon, Heathered Flint (64) 3M5Z-7411600-BA 2003-2007 Wagon, Heathered Black Ink (00) 3M5Z-7411600-CA 2003-2007 Cargo Net, Retention 4-Door/Wagon Envelope Style YS4Z-54550A66-AA 2000-2007 Cargo Organizer 3-Door/5-Door/Sedan Black, For Use Without Subwoofer 5M5Z-54115A00-AAA 2005-2007 Cargo Organizer, Interior Wagon Black, With Ford Logo F8CZ-54115A00-BAA 2000-2007 Cargo Security Shade For Wagon, Med.… Read More
Download 2007 Ford Focus Accessories List Guide
Filed Under (Other Manuals) by Doe Namblas on 09-12-2013
Download Removing – Remove driver’s-side airbag unit and steering wheel. Repair Manual, Body Interior, Repair Group 69 – Remove steering column switches Page 94-37 . – Insert spare or shop key and switch ignition on: access hole will appear in front of switch next to ignition key slot. Installing – Insert length of steel wire or small screwdriver (approx. 2 mm dia.) as far as it will go, as illustrated, and pull lock cylinder out of steering lock housing in direction of arrow. – Ignition switch must be in “ignition on” position. – Push lock cylinder with ignition key all way into steering lock housing and press in firmly until catch engages audibly. – Install steering column switches and steering wheel. Ignition switch, removing and installing Removing Note: It is not necessary to remove the lock cylinder. – Disconnect battery Ground (GND) strap. – Remove driver’s-side airbag unit and steering wheel.… Read More
Download Steering Lock Cylinder – Ignition Switch Removing and Installing
Filed Under (Volkswagen (VW)) by Doe Namblas on 02-01-2014
Download Steering column, assembly WARNING:Special safety precautions and some different procedures apply to vehicles equipped with airbags CAUTION:Before working on the electrical system: Obtain radio anti-theft code. Ignition OFF ! Disconnect battery Ground (GND) strap. Note: After reconnecting battery: Activate vehicle equipment such as radio, clock and power windows as per service procedures and/or Owner’s Manual. On vehicles equipped with OBD II, activate readiness code. Refer to Powertrain Management, Computers and Control Systems, Testing and Inspection, Procedures See: Powertrain Management/Computers and Control Systems/Testing and Inspection For further information on the steering column assembly, refer to Steering and Suspension, Steering, Steering Column, Service and Repair. 1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig.… Read More
Download 2000 Volkswagen Cabrio Ignition Switch: Service and Repair
Filed Under (Hyundai) by Doe Namblas on 31-12-2013
Download NOTE: Both pulse generator-B inspection and TCM reprogramming procedures should be performed. PULSE GENERATOR-B INSPECTION PROCEDURE: 1. Open and secure the hood. 2. Remove the resonator. 3. Locate the pulse generator under the battery tray. Disconnect the pulse generator connector (blue) and remove the pulse generator male connector (black) from the bracket. 4. Using an ohmmeter, check the resistance between terminal No. 3 and No. 4 in the disconnected pulse generator male connector (black color). Resistance value: 215-275W (at 20°C or 68°F) If the resistance is lower or higher than the specification, replace the pulse generator (P/N 45955-22700). If the resistance is within specification go to Step 5. 5. Clean both ends of the disconnected pulse generator connectors with aerosol electrical contact cleaner. 6. Apply contact grease (P/N 00305-F0000-39, NYOGEL 760G), into all four terminal openings of the blue female connector until each terminal opening is completely filled with grease.… Read More
Download 2001 Hyundai Accent GS Transmission Speed Sensor
Filed Under (Cadillac) by Doe Namblas on 28-03-2014
Download When performing service around Supplemental Inflatable Restraint (SIR) system components or wiring, the SIR system must be disabled. Failure to do so could result in possible air bag deployment, personal injury, or unneeded SIR system repairs. Catera Disconnect the negative battery cable. 1. Remove the steering wheel. 2. Remove the inflatable restraint steering wheel module coil. 3. Insert a small pointed awl or wire into the ignition lock cylinder release pinhole. 4. Pull out the ignition lock cylinder. 5.Fig. Insert a pointed tool into the release pin hole To install: Install the lock cylinder. Look into the hole that receives the lock cylinder on the lower RH side in order to locate the locking lever. 1. Carefully push down on the locking lever using a small flat-bladed tool until an audible click is heard. 2. Place the lock cylinder into the empty hole. 3. 6. Install the inflatable restraint steering wheel module coil.… Read More
Download 1990-1998 GM Cadillac Deville Ignition Lock Cylinder REMOVAL & INSTALLATION
Filed Under (Saturn) by Doe Namblas on 01-01-2014
Download REMOVAL 1. Remove shroud fasteners (5.5 mm hex head) and remove steering column upper shroud panel. 2. Insert key into ignition lock cylinder and rotate to ACC position. 3. Depress the square locking button on the top of ignition module assembly and slide lock cylinder assembly from ignition module housing. INSTALLATION IMPORTANT : Actuator blade within ignition module housing must be in the ACC position to install lock cylinder assembly. If rotated, replace it to the ACC position using needle nose pliers. Installation is the reverse of Removal.Note: Make sure locking button locks into opening lock cylinder module. Torque steering column lower trim cover bolts to 26 in.lbs. (3 Nm)… Read More
Download 1995 Saturn Wagon Ignition Lock Cylinder
Filed Under (Saturn) by Doe Namblas on 01-01-2014
Download IMPORTANT: The important statement at the beginning of the “Ignition Lock Cylinder removal procedure on page 188 in the 2000/2001 Saturn S-Series Body/Electrical Volume II Service Manual is incorrect. Please cross out the important on that page and write in the following important statement. IMPORTANT: When replacing the ignition lock cylinder only, the passlock relearn procedure is not required. 1. Disconnect negative battery cable. 2. Remove lock cylinder bezel from steering column shroud by carefully prying with a thin bladed screwdriver. Zoom Sized for Print 3. Remove shroud fasteners and remove steering column upper and lower shroud panels. 4. Insert key into ignition lock cylinder and rotate to RUN position. ^If ignition lock cylinder can be rotated to RUN position, continue to step 30. ^If ignition lock cylinder cannot be rotated to RUN position, continue with next step. Zoom Sized for Print 5. Using a light hammer and brass drift, tap lightly on the top side of the ignition housing assembly at the location indicated in the illustration, while trying to turn the ignition key.… Read More
Download 2000 Saturn SL2 Conversion Calculator
Filed Under (Infiniti) by Doe Namblas on 24-12-2013
Download 2000 – 2001 I30 (CA33) 1999 I30 (CA32) 1999.5 – 2001 QX4 (JR50) 1997 – 2001 Q45 (FY33) 2000 – 2001 G20 (P11) APPLIED VINS: All APPLIED DATES: Start of production SERVICE INFORMATION This bulletin describes and introduces new features of the Infiniti Vehicle Immobilizer System/Nissan Anti-Theft System (IVIS/NATS). The system is standard equipment on each of the applied vehicles listed above. The IVIS/NATS will not allow the engine to start without the use of a registered ignition key. If a vehicle will not start and the Security lamp is on solid, it may be because the ignition keys were not properly registered into the vehicle’s NATS IMMU (Immobilizer control unit). In this case, there will be a “DIFFERENCE OF KEY” code stored in the NATS IMMU. When the NATS ignition key, IMMU, or ECM (ECCS control unit) are replaced, C/U initialization is necessary. It is also necessary when registering keys and as part of many NATS Service Manual diagnostic procedures.… Read More
Download 1997 – 2001 Infiniti Q45 ENGINE WILL NOT START
Filed Under (Mercedes-Benz) by Doe Namblas on 26-11-2013
Download Vehicle Application: 2000 Mercedes-Benz ML320 3.2L 2001 Mercedes-Benz E320 3.2L 2001 Mercedes-Benz C240 2.6L 2001 Mercedes-Benz E320 4Matic 3.2L 2001 Mercedes-Benz C320 3.2L 2002 Mercedes-Benz ML320 3.2L Customer Concern: Engine light is on with no acceleration. Fault code is P0120. Tests/Procedures: 1. Connect scan tool and monitor voltages of pedal sensor B37. Signal 1 (Accelerator pedal position: Idle speed):[0.2...0.5] V Signal 2 (Accelerator pedal position: Idle speed):[0.1...0.5] V Signal 1 (Accelerator pedal position:Kickdown):[4.3...4.8] V Signal 2 (Accelerator pedal position:Kickdown):[2.1...2.5] V 2. If voltages are out of specification verify correct reference voltage to sensor by measuring between pins 6 (Black/White wire) and pin 1 (Blue/Grey wire) on pedal sensor connector. Voltage needs to be between 4.75 and 5.25 volts. 3. Test throttle body voltages with scan tool. Potentiometer #2 signal voltage ignition on, accelerator pedal position CTP 0.3-0.9 VDC, WOT > CTP value Potentiometer #1 signal voltage Ignition on, accelerator pedal position CTP 4.0-4.6 VDC, WOT < CTP value.… Read More
Download 2001 Mercedes-Benz SLK320 Engine light is on with no acceleration